2004 SUBARU FORESTER turn signal bulb

4AT(H4DOTC)-39
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
45 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Disconnect the connectors from TCM and
combination meter.
2) Measure the resistance of harness
between TCM and combination meter.
Connector & terminal
(B55) No. 4 — (i12) No. 11:Is the resistance less than 1
Ω?Go to step 65.Repair the open
circuit in harness
between TCM con-
nector and combi-
nation meter.
46 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM,
inhibitor switch and combination meter.
3) Measure the resistance of harness
between TCM and chassis ground.
Connector & terminal
(B55) No. 4 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 47.Repair the ground
short circuit in “D”
range circuit.
47 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from TCM and
inhibitor switch.
3) Measure the resistance of harness
between TCM and inhibitor switch connector.
Connector & terminal
(B54) No. 16 — (T7) No. 11:Is the resistance less than 1
Ω?Go to step 48.Repair the open cir-
cuit in harness
between TCM and
inhibitor switch con-
nector, and poor
contact in coupling
connector.
48 CHECK INPUT SIGNAL FOR TCM.
1) Turn the ignition switch to OFF.
2) Connect the connector to TCM and inhibitor
switch.
3) Turn the ignition switch to ON.
4) Shift the select lever to “3” range.
5) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B54) No. 16 (+) — Chassis ground (–):Is the voltage less than 1 V? Go to step 49.Go to step 65.
49 CHECK INPUT SIGNAL FOR TCM.
1) Shift the select lever except for “3” range.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B54) No. 16 (+) — Chassis ground (–):Is the voltage more than 8 V? Go to step 65.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
50 CHECK “3” RANGE INDICATOR LIGHT
BULB.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.
3) Remove the “3” range indicator light bulb
from combination meter.Is the “3” range indicator light
bulb OK?Go to step 51.Replace the “3”
range indicator light
bulb. 10, Combination
Meter Assembly.>
51 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Disconnect the connectors from TCM and
combination meter.
2) Measure the resistance of harness
between TCM and combination meter.
Connector & terminal
(B54) No. 16 — (i12) No. 10:Is the resistance more than 1
Ω?Go to step 65.Repair the open
circuit in harness
between TCM con-
nector and combi-
nation meter, and
poor contact in
TCM connector. Step Check Yes No

4AT(H4DOTC)-40
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
52 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM,
inhibitor switch and combination meter.
3) Measure the resistance of harness
between TCM connector and chassis ground.
Connector & terminal
(B54) No. 16 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 53.Repair the ground
short circuit in “3”
range circuit.
53 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from TCM and
inhibitor switch.
3) Measure the resistance of harness
between TCM and inhibitor switch connector.
Connector & terminal
(B54) No. 4 — (T7) No. 4:Is the resistance less than 1
Ω?Go to step 54.Repair the open cir-
cuit in harness
between TCM and
inhibitor switch con-
nector, and poor
contact in coupling
connector.
54 CHECK INPUT SIGNAL FOR TCM.
1) Turn the ignition switch to OFF.
2) Connect the connector to TCM and inhibitor
switch.
3) Turn the ignition switch to ON.
4) Shift the select lever to “2” range.
5) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B54) No. 4 (+) — Chassis ground (–):Is the voltage less than 1 V? Go to step 55.Go to step 65.
55 CHECK INPUT SIGNAL FOR TCM.
1) Shift the select lever except for “2” range.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B54) No. 4 (+) — Chassis ground (–):Is the voltage more than 8 V? Go to step 65.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
56 CHECK “2” RANGE INDICATOR LIGHT
BULB.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.
3) Remove the “2” range indicator light bulb
from combination meter.Is the “2” range indicator light
bulb OK?Go to step 57.Replace the “2”
range indicator light
bulb. 10, Combination
Meter Assembly.>
57 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Disconnect the connectors from TCM and
combination meter.
2) Measure the resistance of harness
between TCM and combination meter.
Connector & terminal
(B54) No. 4 — (i12) No. 4:Is the resistance less than 1
Ω?Go to step 65.Repair the open
circuit in harness
between TCM and
combination
meter, and poor
contact in TCM
connector.
58 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM,
inhibitor switch and combination meter.
3) Measure the resistance of harness
between TCM and chassis ground.
Connector & terminal
(B54) No. 4 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 59.Repair the ground
short circuit in “2”
range circuit. Step Check Yes No

4AT(H4DOTC)-41
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
59 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM and
inhibitor switch.
3) Measure the resistance of harness
between TCM and inhibitor switch connector.
Connector & terminal
(B54) No. 10 — (T7) No. 6:Is the resistance less than 1
Ω?Go to step 60.Repair the open cir-
cuit in harness
between TCM and
inhibitor switch con-
nector, and poor
contact in coupling
connector.
60 CHECK INPUT SIGNAL FOR TCM.
1) Turn the ignition switch to OFF.
2) Connect the connector to TCM and inhibitor
switch.
3) Turn the ignition switch to ON.
4) Shift the select lever to “1” range.
5) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B54) No. 10 (+) — Chassis ground (–):Is the voltage less than 1 V? Go to step 61.Go to step 65.
61 CHECK INPUT SIGNAL FOR TCM.
1) Shift the select lever except for “1” range.
2) Measure the voltage between TCM and
chassis ground.
Connector & terminal
(B54) No. 10 (+) — Chassis ground (–):Is the voltage more than 8 V? Go to step 65.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
62 CHECK “1” RANGE INDICATOR LIGHT
BULB.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.
3) Remove the “1” range indicator light bulb
from combination meter.Is the “1” range indicator light
bulb OK?Go to step 63.Replace the “1”
range indicator light
bulb. 10, Combination
Meter Assembly.>
63 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Disconnect the connectors from TCM and
combination meter.
2) Measure the resistance of harness
between TCM and combination meter.
Connector & terminal
(B54) No. 10 — (i12) No. 5:Is the resistance less than 1Ω? Go to step 65.Repair the open
circuit in harness
between TCM and
combination meter,
poor contact in
TCM connector.
64 CHECK HARNESS CONNECTOR BETWEEN
TCM AND INHIBITOR SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM,
inhibitor switch and combination meter.
3) Measure the resistance of harness
between TCM connector and chassis ground.
Connector & terminal
(B54) No. 10 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 65.Repair the ground
short circuit in “1”
range circuit.
65 CHECK POOR CONTACT.Is there poor contact in inhibi-
tor switch circuit?Repair the poor
contact.Go to step 66.
66 CHECK INHIBITOR SWITCH.Is the inhibitor switch in proper
position?Replace the TCM.
Transmission Con-
trol Module
(TCM).>Adjust the inhibi-
tor switch and
select cable. to 4AT-51, Inhibi-
tor Switch.> and
Select Cable.> Step Check Yes No

4AT(H4DOTC)-114
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure without Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK FWD SWITCH.When the fuse is inserted to
FWD switch, does LED light
up?Go to step CHECK
POWER SWITCH.
4AT(H4DOTC)-
116, CHECK
POWER SWITCH,
Diagnostic Proce-
dure without Diag-
nostic Trouble
Code (DTC).>Go to step 2.
2 CHECK FWD INDICATOR LIGHT.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.Is the FWD indicator light bulb
OK?Go to step 3.Check the combi-
nation meter.
Combination
Meter Assembly.>
3 CHECK HARNESS CONNECTOR BETWEEN
TCM AND FWD SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from TCM and
FWD switch.
3) Measure the resistance of harness
between TCM and FWD switch connector.
Connector & terminal
(B56) No. 17 — (F27) No. 36:Is the resistance less than 1
Ω?Go to step 4.Repair the open
circuit in harness
between TCM and
FWD switch con-
nector.
4 CHECK HARNESS CONNECTOR BETWEEN
TCM AND FWD SWITCH.
Measure the resistance of harness connector
between TCM and body to make sure that cir-
cuit does not short.
Connector & terminal
(B56) No. 17 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 5.Repair the short
circuit in harness
between TCM and
FWD switch con-
nector.
5 CHECK HARNESS CONNECTOR BETWEEN
FWD SWITCH AND CHASSIS GROUND.
Measure the resistance of harness between
FWD switch and chassis ground.
Connector & terminal
(F27) No. 35 — Chassis ground:Is the resistance less than 1
Ω?Go to step 6.Repair the open
circuit in harness
between FWD
switch connector
and chassis
ground.
6 CHECK INPUT SIGNAL FOR TCM.
1) Turn the ignition switch to OFF.
2) Connect the connector to FWD switch and
TCM.
3) Turn the ignition switch to ON.
4) Measure the signal voltage for TCM while
installing the fuse to FWD switch connector.
Connector & terminal
(B56) No. 17 (+) — Chassis ground (
−):Is the voltage less than 1 V? Go to step 7.Go to step 11.
7 CHECK INPUT SIGNAL FOR TCM.
Measure the signal voltage for TCM while
removing the fuse from FWD switch connector.
Connector & terminal
(B56) No. 17 (+) — Chassis ground (
−):Is the voltage more than 10.5
V?Go to step 8.Replace the TCM.
Transmission Con-
trol Module
(TCM).>
8 CHECK HARNESS CONNECTOR BETWEEN
TCM AND COMBINATION METER.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from TCM and
combination meter.
3) Measure the resistance of harness between
TCM and combination meter connector.
Connector & terminal
(B56) No. 14 — (i10) No. 22:Is the resistance less than 1
Ω?Go to step 9.Repair the open
circuit in harness
between TCM and
combination meter
and poor contact
in coupling con-
nector.

4AT(H4DOTC)-118
AUTOMATIC TRANSMISSION (DIAGNOSTIC)
Diagnostic Procedure without Diagnostic Trouble Code (DTC)
2 CHECK POWER SWITCH OPERATION.When the POWER switch is
turned to ON, does LED light
up?Go to step CHECK
HOLD SWITCH.
4AT(H4DOTC)-
120, CHECK
HOLD SWITCH,
Diagnostic Proce-
dure without Diag-
nostic Trouble
Code (DTC).>Go to step 3.
3 CHECK POWER INDICATOR LIGHT.
1) Turn the ignition switch to OFF.
2) Remove the combination meter.
3) Remove the POWER indicator light bulb
from combination meter.Is the POWER indicator light
bulb OK?Go to step 4.Replace the
POWER indicator
light bulb. IDI-10, Combina-
tion Meter Assem-
bly.>
4 CHECK POWER SWITCH GROUND CIR-
CUIT.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from POWER
switch.
3) Measure the resistance of harness connector
between POWER switch and chassis ground.
Connector & terminal
LHD model
(R92) No. 4 — Chassis ground:
RHD model
(B133) No. 4 — Chassis ground:Is the resistance less than 1
Ω?Go to step 5.Repair the open
circuit in harness
between POWER
switch and chas-
sis ground.
5 CHECK POWER SWITCH.
1) Turn the POWER switch to ON.
2) Measure the resistance between terminals
of POWER switch.
Te r m i n a l s
No. 5 — No. 4:Is the resistance less than 1
Ω?Go to step 6.Replace the
POWER switch.
6 CHECK POWER SWITCH.
1) Turn the POWER switch to OFF.
2) Measure the resistance between terminals
of POWER switch.
Te r m i n a l s
No. 5 — No. 4:Is the resistance more than1
MΩ?Go to step 7.Replace the
POWER switch.
7 CHECK HARNESS CONNECTOR BETWEEN
TCM AND POWER SWITCH.
Measure the resistance of harness connector
between TCM and POWER switch.
Connector & terminal
(B54) No. 8 — (B133) No. 5:Is the resistance less than 1
Ω?Go to step 8.Repair the open
circuit in harness
between TCM and
POWER switch
connector.
8 CHECK HARNESS CONNECTOR BETWEEN
TCM AND POWER SWITCH.
Measure the resistance of harness connector
between TCM connector and chassis ground.
Connector & terminal
(B54) No. 8 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 9.Repair the short
circuit in harness
between TCM and
POWER switch
connector.
9 CHECK INPUT SIGNAL FOR TCM.
1) Connect the connectors to TCM and
POWER switch.
2) Turn the ignition switch to ON (engine OFF).
3) Measure the signal voltage for TCM while
turning POWER switch to OFF.
Connector & terminal
(B54) No. 8 (+) — Chassis ground (–):Is the voltage more than 10 V? Go to step 10.Replace the TCM.
Transmission Con-
trol Module
(TCM).> Step Check Yes No