2004 MITSUBISHI ENDEAVOR checking oil

Fig. 25: Checking Oil Pump Pressure

Courtes
y of MITSUBISHI MOTOR SALES OF AMERICA
.

2004 Mitsubishi Endeavor LS
2004 STEERING Power Steering - Endeavor

Fig. 4: Checking Gear Oil Level

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the gear oil level more than 8 mm (0.3 inch) below the bottom of the
filler plug hole?
YES: Check the oil leakage from differential carrier, and repair if
necessary. Then, refill Hypoid gear oil API classification GL-5 or higher;
Above-23°C (-10°F): SAE 90, 85W-90, 80W-90, From-34 to-23°C (-30
to-10°F
): SAE 80W
, 80W-90
, Below-34°C
(-30°F
): SAE 75W. Then
go to

2004 Mitsubishi Endeavor LS
2004 SUSPENSION Rear Axle < AWD > - Endeavor

Fig. 5: Checking Gear Oil Level

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the gear oil level more than 8 mm (0.3 inch) below the bottom of the
filler plug hole?
YES: Check the oil leakage from differential carrier, and repair if
necessary. Then, refill Hypoid gear oil API classification GL-5 or higher;
Above-23°C
(-10°F): SAE 90, 85W-90, 80W-90, Fro
m-34 to-23°C
(-30

2004 Mitsubishi Endeavor LS
2004 SUSPENSION Rear Axle < AWD > - Endeavor

Fig. 6: Checking Gear Oil Level

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the gear oil level more than 8 mm (0.3 inch) below the bottom of the
filler plug hole?
YES: Check the oil leakage from differential carrier, and repair if
necessary. Then, refill Hypoid gear oil API classification GL-5 or higher;
Above-23°C
(-10°F
): SAE 90, 85W-90, 80W-90, Fro
m-34 to-23°C
(-30

2004 Mitsubishi Endeavor LS
2004 SUSPENSION Rear Axle < AWD > - Endeavor

Fig. 7: Checking Gear Oil Level

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the gear oil level more than 8 mm (0.3 inch) below the bottom of the
filler plug hole?
YES: Refill Hypoid gear oil API classification GL-5 or higher; Above-23°
C (-10°F): SAE 90, 85W-90, 80W-90, From-34 to-23°C (-30 to-10°F):
SAE 80W, 80W-90, Below-34°C
(-30°F
): SAE 75W. Then
go to Ste
p 4.

2004 Mitsubishi Endeavor LS
2004 SUSPENSION Rear Axle < AWD > - Endeavor

Above-23°C (-10°F): SAE 90, 85W-90, 80W-90
From-34 to-23°C (-30 to-10°F): SAE 80W, 80W-90
Below-34°C (-30°F): SAE 75W
Fig. 14: Checking Gear Oil Level

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3.
Tighten the filler plug to the specified torque.

2004 Mitsubishi Endeavor LS
2004 SUSPENSION Rear Axle < AWD > - Endeavor

Fig. 7: Checking Overrunning Clutc
h
Courtesy of KIA MOTORS AMERICA, INC.
FRONT & REAR BRACKET BUSHING CHECK Inspect the bushing for wear or burrs. If the bushing is worn or burred, replace the
front bracket assembly or rear bracket assembly. ARMATURE CHECK 1. Check that the armature coil is not grounded.
2. Place armature in a growler. See Fig. 8
.
3. Hold a thin steel blade parallel and just above while rotating the armature
slowly in the growler. A shorted armature will cause a blade to vibrate and
attract to the core. Replace the shorted armature.
4. Check the insulation between the armature coil cores and the commutator
segments. They are normal if there is no continuity. See Fig. 9
.
5. Check for continuity between the segments. The condition is normal if there is
continuit
y. See Fig. 10
.

2004 Mitsubishi Endeavor Limited
2004 STARTING & CHARGING SYSTEMS Starters - Endeavor

Fig. 9: Checking Armature Coil Ground Test

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor Limited
2004 STARTING & CHARGING SYSTEMS Starters - Endeavor