2004 MITSUBISHI ENDEAVOR interval

Fig. 12: Drive Belt Routing Power Steering Pump Belt)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
SPECIFICATIONS COOLING SYSTEM SPECIFICATIONS COOLING SYSTEM SPECIFICATIONS Application
Specification
Coolant Replacement Interval
60,000 Miles
Coolant CapacityAWDWith Towing Kit
10.1 Qts. (9.6L)
Without Towing Kit
9.5 Qts. (9.0L)
FWD
9.5 Qts. (9.0L)
Pressure Cap
14-18 psi (.98-1.27

2004 Mitsubishi Endeavor Limited
2004 ENGINE COOLING Specifications & Drive Belt Routing - Endeavor

between the station transmitter and the vehicle), and noise will appear. < This
is called first fading, and gives a steady buzzing noise. >
3. If a direct signal hits the antenna at the same time as a signal reflected by
obstructions such as mountains or buildings, interference of the two signals
will generate noise. When moving, noise will appear each time the vehicle's
antenna passes through this kind of obstructed area. The strength and interval
of the noise varies according to the signal strength and the conditions of
deflection. < This is called multipath noise, and is a repetitive buzzing. >
Fig. 137: Identif
ying Ins
pection Procedure (Noise Is Present While Movin
g
(Fm)) 2 Of 2

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
4. Since FM stereo transmission and reception has a weaker field than monaural,
it is often accompanied by a hissing noise.
After taking measures to prevent the noise, check that no noise occurs.
5. Change to a different station with a stronger wave to boost resistance to
interference.
6. Su
ppress hi
gh tones to reduce noise.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

2004 BODY & ACCESSORIES
Windshield Wiper And Washer - Endeavor
GENERAL DESCRIPTION WINDSHIELD WIPER AND WASHER OPERATION WINDSHIELD LOW-SPEED (AND HIGH-SPEED) WIPER OPERATION
If the windshield low-speed wiper switch is turned to the ON position with the
ignition switch at the "ACC" or "ON" position, the column switch sends a low-
speed wiper ON and high-speed wiper OFF signals to the front-ECU. This
turns the wiper signal on and the wiper speed control relay off (low-speed),
causing the wipers to operate at low-speed. If the windshield high-speed wiper switch is turned to the ON position, the
column switch sends a low-speed wiper OFF and high-speed wiper ON signals
to the front-ECU. This turns both the wiper signal and the wiper speed control
relay on (high-speed), causing the wipers to operate at high-speed.
WINDSHIELD INTERMITTENT WIPER OPERATION The ETACS-ECU calculates the wiper operation interval according to the voltage
signal sent from the column switch. Then the ETACS-ECU sends a signal to the
front-ECU. The front-ECU determines the wiper operation interval and turns on the
wiper relay signal relay. This causes the wiper auto stop relay to turn on. Then the
wiper auto stop relay will turn off after the wipers reach the park position. This
causes the wiper signal relay and then the wipers to turn off. If the wiper signal
relay remains off for the wiper operation interval, the relay turns on again, causing
the wipers to operate in intermittent mode. WINDSHIELD MIST WIPER OPERATION
NOTE: The windshield wiper speed is adjustable with the built-
in wiper speed control relay. High-speed operations
take place when the wiper speed control relay is set to
"ON" and low-speed operations take place when the
wiper speed control relay is set to "OFF".

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Windshield Wiper And Washer - Endeavor


2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Windshield Wiper And Washer - Endeavor

ON-VEHICLE SERVICE WINDSHIELD INTERMITTENT WIPER VOLUME CHECK 1. If the windshield intermittent wiper volume is operated, the wiper interval
should change.
2. Holding the windshield intermittent wiper volume, input the simulated vehicle
speed with scan tool MB991958 and check that the wiper interval changes as
the vehicle speed changes.
3. If not, carry out the troubleshooting (Refer to SWS DIAGNOSIS
).
WINDSHIELD WASHER FLUID EJECTION CHECK The windshield washer nozzle aiming can not be adjusted. If the washer nozzles do
not spray washer fluid within the swept area, check the nozzles as follows.
1. Check that the windshield washer nozzles are fitted on the hood correctly, and
reinstall them if necessary. windshield wiper operates when the ignition switch is at the
"ACC" or "ON" position. But, if it enters the fail-safe mode,
the wiper can operate only when the ignition switch is at the
"ON" position).
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Windshield Wiper And Washer - Endeavor