2004 MITSUBISHI ENDEAVOR checking oil

Fig. 63: Checking Notches In Each Rocker Shaft Are Facing Directio
n
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
>>E<< CAMSHAFT OIL SEAL INSTALLATION 1. Apply engine oil to the camshaft oil seal lip.
Fig. 64: Identifying Installation Of Camshaft Oil Seal (Left Bank)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor Limited
2004 ENGINE Engine - Endeavor

Fig. 164: Checking Refrigerant Temperature Switch

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2. When the oil temperature reaches the standard value, check that voltage is
supplied between the terminals.
Standard value:


2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor

IGNITION COIL CHEC
K
Check by the following procedure, and replace the coil if there is a malfunction. PRIMARY COIL AND IGNITION POWER TRANSISTOR CONTINUITY CHECK Fig. 3: Checking Primary Coil And Ignition Power Transistor

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
NOTE: An analog-type ohmmeter should be used.
NOTE: Connect the negative probe of the ohmmeter to terminal 1.
CAUTION: This test must be performed quickly (in less than 10
seconds) to prevent coil from burning and ignition
power transistor from breaking.
2004 Mitsubishi Endeavor Limited 2004 ENGINE Ignition System - Endeavor

2004 STEERING
Power Steering - Endeavor
GENERAL DESCRIPTION Power steering has been adopted in all vehicles to make the steering system easier
to handle.
A 4-spoke steering wheel is used. A steering column has a shock absorbing mechanism and a tilt steering
mechanism. A rack and pinion steering gear is used. An oil pump responsive to engine RPM is used, which, with tuning for a rigid
gear box mount, improves steering stability at high speeds. The separate plastic resin oil reservoir reduces weight and makes fluid level
checking easier.
Fig. 1: Identifying Power Steering Components

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
POWER STEERING DIAGNOSIS
2004 Mitsubishi Endeavor LS
2004 STEERING Power Steering - Endeavor


2004 Mitsubishi Endeavor LS
2004 STEERING Power Steering - Endeavor

Fig. 5: Checking Fluid Level (Shrill Noise)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
STEP 2. Check for seizure in the oil pump.
Q: Is there seizure?
YES: Replace the part. Then go to Step 3.
NO: Go to Step 3.
STEP 3. Retest the system.
Confirm that no noise is generated.

2004 Mitsubishi Endeavor LS
2004 STEERING Power Steering - Endeavor

Fig. 21: Checking Steering Wheel Return To Center

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
DRIVE BELT TENSION CHECK Refer to 7. DRIVE BELTS (FOR GENERATOR, POWER STEERING OIL PUMP AND AIR CONDITIONING) (CHECK)
.
FLUID LEVEL CHECK
2004 Mitsubishi Endeavor LS
2004 STEERING Power Steering - Endeavor

1. Park the vehicle on a flat, level surface.
2. Start the engine, and then turn the steering wheel several times to raise the
temperature of the fluid to approximately 50 - 60°C (122 - 140°F).
3. With the engine running, turn the wheel all the way to the left and right several
times.
4. Check the fluid in the oil reservoir for foaming or milkiness. Check the
difference of the fluid level when the engine is stopped, and while it is running.
If the fluid contains air or has milky appearance, or the fluid level fluctuate by
5 mm (0.2 inch) or more, power steering system air bleeding should be done.
Refer to POWER STEERING SYSTEM AIR BLEEDING
.
Fig. 22: Checking Fluid Level

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
FLUID REPLACEMENT
2004 Mitsubishi Endeavor LS
2004 STEERING Power Steering - Endeavor

2. Bleed air, then turn the steering wheel several times while the vehicle is not
moving so that the temperature of the fluid rises to approximately 50 - 60°C
(122 - 140°F).
3. Start the engine and idle it at 700 +/- 100 r/min.
4. Fully close the shut-off valve of the pressure gauge and measure the oil pump
relief pressure to confirm that it is within the standard value range. Open it
again immediately after checking the pressure.
Standard value: 9.3 - 9.8 MPa (1,349 - 1,421 psi)
CAUTION: The pressure gauge shut-off valve must not
remain closed for more than 10 seconds.

2004 Mitsubishi Endeavor LS
2004 STEERING Power Steering - Endeavor