2004 MITSUBISHI ENDEAVOR parking brake

Fig. 8: Parking Brake Switch Specification

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
PARKING BRAKE LINING SEATING PROCEDURE Perform lining seating by the following procedure when replacing the parking brake
shoe assemblies or the rear brake discs, or when brake performance is insufficient.
1. Adjust the parking brake pedal stroke to the standard value (Refer to ON
-
VEHICLE SERVICE
).
2. Depress the parking brake pedal with a force of 100 - 150 N (23 - 34 pounds).
3. Drive the vehicle at a constant speed of 35 - 50 km/h (22 - 31 mph) for 100
meters (328 feet).
4. Release the parking brake and let the brakes cool for five to ten minutes.
5. Repeat the procedure in steps 2. to 4. four to five times.
PARKING BRAKE PEDAL REMOVAL AND INSTALLATION Post-installation Operation
Parking Brake Pedal Stroke Check and Adjustment (Refer to ON
-VEHICLE
SERVICE
.)
CAUTION: Perform lining seating in a place with good visibility,
and pay careful attention to safety.

2004 Mitsubishi Endeavor LS 2004 BRAKES Parking Brakes - Endeavor

Fig. 9: Exploded View Of Parking Brake Pedal Stroke

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSTALLATION SERVICE POINT >>A<< FRONT PARKING BRAKE CABLE/PARKING BRAKE LEVER NUTS/PARKING BRAKE CABLE CLIP
2004 Mitsubishi Endeavor LS 2004 BRAKES Parking Brakes - Endeavor

INSTALLATION 1. Tighten the parking brake lever nuts securely.
Fig. 10: Tightening Parking Brake Lever Nuts

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Insert the parking brake cable clip securely as illustrated.
3. Check that the pawl has been bent. In addition, check that the bent pawl does
not interfere with the front parking brake cable.
PARKING BRAKE CABLE REMOVAL AND INSTALLATIONNOTE: The bent pawl prevents the front parking brake cable from
falling off the parking brake pedal.
2004 Mitsubishi Endeavor LS 2004 BRAKES Parking Brakes - Endeavor

< FRONT PARKING BRAKE CABLE
>
Fig. 11: Removing/Installing Front Parking Brake Cable

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
< REAR PARKING BRAKE CABLE>
2004 Mitsubishi Endeavor LS 2004 BRAKES Parking Brakes - Endeavor

Fig. 12: Removing/Installing Rear Parking Brake Cable

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSTALLATION SERVICE POINTS >>A<< FRONT PARKING BRAKE CABLE INSTALLATION Install the front parking brake cable securely to the cable support of the parking brake cable bracket.
CAUTION: Be careful not to widen the cable support slit when
installing the front parking brake cable.

2004 Mitsubishi Endeavor LS 2004 BRAKES Parking Brakes - Endeavor

Fig. 13: Installing Front Parking Brake Cable

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
>>B<< PARKING BRAKE LEVER NUTS/PARKING BRAKE CABLE CLIP INSTALLATION 1. Ti
ghten the
parkin
g brake lever nuts securel
y.

2004 Mitsubishi Endeavor LS 2004 BRAKES Parking Brakes - Endeavor

Fig. 14: Tightening Parking Brake Lever Nuts

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Insert the parking brake cable clip securely as illustrated.
3. Check that the pawl has been bent. In addition, check that the bent pawl does
not interfere with the front parking brake cable.
PARKING BRAKE LINING AND DRUM REMOVAL AND INSTALLATIONNOTE: The bent pawl prevents the front parking brake cable from
falling off the parking brake pedal.
2004 Mitsubishi Endeavor LS 2004 BRAKES Parking Brakes - Endeavor

Fig. 15: Removing/Installing Parking Brake Lining And Drum (1 Of 2)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS 2004 BRAKES Parking Brakes - Endeavor