Page 2811 of 3870
Fig. 24: Installing Shoe
-To
-Anchor Springs (2 Of 2)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
INSPECTION PARKING BRAKE LINING AND BRAKE DRUM CHECK 1. Measure the thickness of the brake lining at several places.
Standard value: 2.8 mm (0.11 inch)
Minimum Limit: 1.0 mm (0.04 inch)
2004 Mitsubishi Endeavor LS 2004 BRAKES Parking Brakes - Endeavor
Page 2812 of 3870
Fig. 25: Measuring Thickness Of Brake Lining
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS 2004 BRAKES Parking Brakes - Endeavor
Page 2813 of 3870
2. If the thickness of the brake lining is below the limit, replace the shoe
assemblies on both sides of the vehicle. Never replace only one side.
3. Measure the inside diameter of the brake disc in two places or more.
Standard value: 190.0 mm (7.48 inches)
Limit: 191.0 mm (7.52 inches)
Fig. 26: Measuring Inside Diameter Of Brake Disc
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
4. If the inside diameter exceeds the limit, or if it is excessively worn on one side,
replace the brake disc.
SPECIFICATIONS
2004 Mitsubishi Endeavor LS 2004 BRAKES Parking Brakes - Endeavor
Page 2814 of 3870
FASTENER TIGHTENING SPECIFICATIONSFig. 27: Fastener Tightening Specifications Chart
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
SERVICE SPECIFICATIONS Fig. 28: Service Specifications Chart
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
LUBRICANT Fig. 29: Lubricant Specifications Chart
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2004 Mitsubishi Endeavor LS 2004 BRAKES Parking Brakes - Endeavor
Page 2944 of 3870
Fig. 11: Identifying Special Tools (4 Of 4)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
ON-VEHICLE SERVICE REAR AXLE TOTAL BACKLASH CHECK 1. Park the vehicle on a flat, level surface.
2. Place the selector lever to the neutral position. Apply the parking brake and
jack up the vehicle.
3. Turn the propeller shaft clockwise as far as it will go. Make the mating marks
on the dust cover of the com
panion flan
ge and on the differential carrier.
2004 Mitsubishi Endeavor LS
2004 SUSPENSION Rear Axle < AWD > - Endeavor
Page 3302 of 3870
CIRCUIT OPERATION The meter-ECU detects the brake fluid level switch ON/OFF and controls the brake
warning light ON/OFF.
The TCL/ASC-ECU and the meter-ECU are connected each other via a CAN bus
line, and the meter-ECU informs the TCL/ASC-ECU whether the brake fluid level
switch is turned on or off. ABS DTC SET CONDITIONS This DTC is set when all of the following cases are met.
When the amount of the brake fluid is less than lower limit. Vehicle speed is 15 km/h or more
TROUBLESHOOTING HINTS (The most likely causes for this DTC is to set are:)
Current trouble
Brake fluid is not filled Damaged wiring harness or connector Malfunction of the hydraulic unit (integrated with TCL/ASC-ECU) Malfunction of the combination meter (integrated with meter ECU)
Past trouble
Carry out diagnosis with particular emphasis on connector(s) or wiring harness
between the combination meter circuit (terminal 7) to the brake fluid level
switch or parking brake switch. For diagnosis procedures, refer to HOW TO TREAT PAST TROUBLE
).
DIAGNOSIS Required Special Tools:
MB991958: Scan Tool
(MUT-III Sub Assembl
y) this diagnosis, diagnose the CAN bus lines.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3307 of 3870
6. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC C1345 set?
YES: Go to Step 3.
NO: The procedure is complete.
STEP 3. Check the brake warning light.
Check that the brake warning light illuminates with the parking brake lever
pulled up.
Q: Does the brake warning light illuminate?
YES: Replace the hydraulic unit (integrated with TCL/ASC-ECU). Then
go to Step 12.
NO: Go to Step 4.
STEP 4. Check the brake fluid amount.
Q: Is the brake fluid within lower and upper limits of the reservoir?
YES: Go to Step 5.
NO: Check the basic brake system to determine why the brake fluid was
decreased.
STEP 5. Check the brake warning light.
1. Disconnect brake fluid level switch connector A-04 and parking brake
switch connector
C-34.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
Page 3309 of 3870
Fig. 129: Disconnecting Parking Brake Switch Connector C
-34
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Turn the ignition switch to the "ON" position.
Q: Does the brake warning light illuminate?
YES: Go to Step 6.
NO: Check the brake fluid level switch (Refer to BRAKE FLUID
LEVEL SENSOR CHECK
, ) and parking brake switch and replace
them if necessary. Then go to Step 12.
STEP 6. Measure the resistance at combination meter connector C-102.
1. Disconnect brake fluid level switch connector A-04 and parking brake
switch connector
C-34.
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor
