2004 MITSUBISHI ENDEAVOR parking brake

Fig. 131: Disconnecting Parking Brake Switch Connector C
-34
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Disconnect the connector C-102

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

Fig. 132: Disconnecting Connector C
-102

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Measure the resistance between terminal 7 and ground. Check for
continuity.
Q: Does the continuity exist?
YES: Go to Step 7.
NO: Replace the combination meter (integrated with meter ECU). Then
go to Step 12.
STEP 7. Check intermediate connector C-31, grounding connector A-18,
brake fluid level switch connector A-04, joint connector C-04, combination
meter connector C-102 and parking brake switch connector C-34 for
loose, corroded or damaged terminals, or terminals pushed back in the
connector.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

Fig. 134: Checking Intermediate Connector C
-31
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is intermediate connector C-31, grounding connector A-18, brake fluid
level switch connector A-04, joint connector C-04, combination meter
connector C-102 and parking brake switch connector C-34 damaged?
YES: Repair or replace the damaged component(s). Then go to Step 12.
NO: Go to Step 8.
STEP 8. Check the harness wires between joint connector C-04 (terminal
13) and parking brake switch connector C-34 (terminal 1).
Fig. 135: Checking Harness Wires Between Joint Connector C
-04 And
Parking Brake Switch Connector C
-34
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

Q: Is the harness wires between joint connector C-04 (terminal 13) and
parking brake switch connector C-34 (terminal 1) damaged?
YES: Repair the wiring harness. Then go to Step 12.
NO: Go to Step 9.
STEP 9. Check the harness wires between brake fluid level switch
connector A-04 (terminal 1) and joint connector C-04 (terminal 12).
Fig. 136: Checking Harness Wires Brake Fluid Level Switch Connector A
-
04
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

Fig. 237: Identifying Special Tools (2 Of 2)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
ON-VEHICLE SERVICE WHEEL SPEED SENSOR OUTPUT VOLTAGE MEASUREMENT Required Special Tool:
MB991219: Inspection Harness
1. Release the parking brake and lift up the vehicle.
2. Disconnect the TCL/ASC-ECU connector A-32, and then use special tool
MB991219 to measure the out
put volta
ge at the harness side connector.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

1. Jack up the vehicle. Then support the vehicle with rigid racks at the specified
jack-up points or place the front or rear wheels on the rollers of the braking
force tester.
2. Release the parking brake, and feel the drag force (drag torque) on each road
wheel. When using the braking force tester, take a reading of the brake drag
force.
3. Connect scan tool MB991958 to the data link connec
tor. CAUTION:
The roller of the braking force tester and the tire
should be dry during testing. When testing the front brakes, apply the parking
brake. When testing the rear brakes, stop the
front wheels with chocks.
CAUTION: To prevent damage to scan tool MB991958,
always turn the ignition switch to the
"LOCK" (OFF) position before connecting or
disconnecting scan tool MB991958.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor