2004 MITSUBISHI ENDEAVOR Rear end

S041
In dash
harness, rear
of center
console. See
Fig. 81
.
S042
In dash
harness, rear
of center
console. See
Fig. 81
.
S043
In dash
harness,
center o
f
dash. See
Fig. 81 .
S044
In dash
harness,
center o
f
dash. See
Fig. 81 .
S045
In dash
harness, left
side of dash.
See Fig. 81
.
S046
In dash
harness, left
side of dash.
See Fig. 81
.
S047
In dash
harness, left
side of dash.
See Fig. 81
.
S048
In dash
harness
, left

2004 Mitsubishi Endeavor LS
2004 MITSUBISHI Endeavor

S070
In floor
harness, left
front door
sill. See Fi
g.
85 .
S071
In floor
harness, left
front door
sill. See Fig.
85 .
S072
In floor
harness, left
front door
sill. See Fi
g.
85 .
S073
In floor
harness, left
front door
sill. See Fi
g.
85 .
S074
In floor
harness, left
rear door sill.
See Fig. 85
.
S075
In floor
harness,
above left
rear
wheelwell.
See Fig. 85
.
S078
In floor
harness,
above left
rear
wheelwell.

2004 Mitsubishi Endeavor LS
2004 MITSUBISHI Endeavor

See Fig. 85
.
S079
In floor
harness,
above left
rear
wheelwell.
See Fig. 85
.
S080
In right front
door harness.
See Fig. 82
.
S081
In left front
door harness.
See Fig. 82
.
S082
In left front
door harness.
See Fig. 82
.
S083
In left front
door harness.
See Fig. 82
.
S085
In liftgate
harness,
center o
f
liftgate. See
Fig. 86 .
S086
In engine
compartment
harness, right
side o
f
engine
compartment.
See Fig. 84 .
In engine
compartment
harness
, right

2004 Mitsubishi Endeavor LS
2004 MITSUBISHI Endeavor

Fig. 19: Removing Front Bracket Assembly

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig. 20: Locating Solder Points

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Assembly Service Points
A) Regulator Assembly Installation - After installing the regulator assembly,
insert a wire through the hold provided on the rear bracket while pressing down
on the brush, and secure the brush. See Fig. 21
.
B) Rotor Assembly Installation - After installing the rotor, remove the wire
used to secure the brush. NOTE: By inserting a wire, the brush will be secured in place,
and the installation of the rotor will be easier.

2004 Mitsubishi Endeavor Limited
2004 STARTING & CHARGING SYSTEMS Generators & Regulators - Endeavor

Fig. 57: Fitting Special Tool MD998443 To Lash Adjuster

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
>>C<< ROCKER ARMS AND SHAFT INSTALLATION 1. Position the end with the larger chamfer at the right on the front bank, and at
the left on the rear bank.
2. Position the side with the oil holes on the lower side
(cylinder head side
).
NOTE: The side with the four bolt holes is on the intake side.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

MD998718: Crankshaft Rear Oil Seal Installer
INSTALLATION SERVICE POINTS >>A<< BLOCK HEATER INSTALLATION Within 30° of the center, install the block heater as shown in Fi
g.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Fig. 148: Checking End Play Of Thrustbearing

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
>>F<< CRANKSHAFT REAR OIL SEAL INSTALLATION Using special tool MD998718, press-fit a new crankshaft rear oil seal into the oil
seal case.
2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Fig. 149: Installing Crankshaft Rear Oil Seal

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
>>G<< OIL SEAL CASE INSTALLATION 1. Apply the sealant Mitsubishi Genuine Part number MD970389 or equivalent to
the oil seal case.
2. Apply a small amount of engine oil to the entire circumference of the oil seal
lip section, and place the oil seal case on the cylinder block. NOTE: Install the oil seal case within 15 minutes after applying
liquid gasket. Then wait at least one hour. Do not start the
engine or let engine oil or coolant touch the sealant during
that time.
2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor