2004 ISUZU TF SERIES lock

IMMOBILIZER SYSTEM 11A-35

Step Action Value(s) Yes No
10 Review and record for scan tool Failure Records data
and DTCs.
Was the action complete? 
Go to Step 11 
11 Following the DTC is stored.
Are there DTC B0001 or B0055 stored?
Go to applicable
DTC table after
Go to Step 12 Go to Step 12
12 Clear the DTCs by "Clear the Information "with scan
tool.
Did the DTCs Cleared? 
Go to Step 12 
13 Select "Display DTCs" with the scan tool.
Are any DTCs stored? 
Go to applicable
DTC table Go to Step 14
14 1. Key position is "ON," engine "OFF."
2. Observe the check engine lamp.
Note: If a key switch is turned ON, check engine lamp
will turn on and a check engine lamp will be turned off
after a few seconds.
Is the check engine lamp "flash"? 
Go to Step 15
Go to Step 20
15 Check the engine control system.
If a problem is found, repair as necessary.
(Refer to section 6E: system check and DTCs)
IMPORTANT:
The replacement ECM must be
programmed the immobilizer data by scan tool.
(Except 4JA1-L Engine)
Was the action complete? 
Go to Step 16 
16 Check the key.
Is a key peculiar to a vehicle? 
Go to Step 18
Go to Step 17
17 Change into a peculiar key.
IMPORTANT:
If replace the key,
after replace lock
cylinders, perform the following below the items.

Replace the keys and key cylinders.

Program the immobilizer system.
(Refer to "Important information on Programming")
Was the action complete? 
Go to Step 18 
18 Check the immobilizer programming functions.


Immobilizer control unit (ICU).


Engine control module (ECM).


Transponder (Key).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete? 
Go to Step 19

19 Operate the DTCs by "Clear the Information" with
scan tool.
Was the action complete? 
Go to Step 20 
20 Attempt to start the engine.
Did the engine start? 
System OK
Refer to
Diagnostic Aids

IMMOBILIZER SYSTEM 11A-39

B0002 IMMOBILIZER NOT PROGRAMMED
Step Action Value(s) Yes No
1 Was the "Immobilizer System Check" performed?

Go to Step 2
Go to Immobilizer
System Check
2 Check the immobilizer programming functions.

Immobilizer control unit (ICU).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete? 
Go to Step 3
Go to Step 5
3 Recheck the DTC.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0002 stored? 
Go to Step 4
Verify repair
4 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the security data by scan tool.
Was the action complete? 
Verify repair 
5 Check the immobilizer programming functions.


Engine control module (ECM).


Immobilizer control unit (ICU).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete? 
Verify repair
Go to Step 6
6 Replace the key and lock cylinder assembly and
immobilizer system (ICU and ECM).
IMPORTANT:


ICU and ECM are not replacing simultaneously.


After replace lock cylinders, perform the following
below the items.


Program the immobilizer system.
(Refer to "Important information on Programming")
Was the action complete? 
Verify repair 

IMMOBILIZER SYSTEM 11A-53

B0013 IMMOBILIZER NOT PROGRAMMED (Only 4JA1-T Engine)
Step Action Value(s) Yes No
1
Was the "Immobilizer System Check" performed?
Go to Step 2
Go to Immobilizer
System Check
2 Check the immobilizer programming functions.

Immobilizer control unit (ICU).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete? 
Go to Step 3
Go to Step 5
3 Recheck the DTC.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0013 stored? 
Go to Step 4
Verify repair
4 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the security data by scan tool.
Was the action complete? 
Verify repair 
5 Check the immobilizer programming functions.


Engine control immobilizer unit.


Immobilizer control unit (ICU).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete? 
Verify repair
Go to Step 6
6 Replace the key and lock cylinder assembly and
immobilizer system (ICU and Engine immobilizer
unit).
IMPORTANT:

ICU and Engine immobilizer unit are not
replacing simultaneously.


After replace lock cylinders, perform the
following below the items.


Program the immobilizer system.
(Refer to "Important information on Programming")
Was the action complete? 
Verify repair 

ANTITHEFT SYSTEM 11B – 1
SECTION 11B
ANTITHEFT SYSTEM
CONTENTS
PAGE
Service Precaution ........................................................................................................ 11B – 3
General Description ...................................................................................................... 11B – 4
Activating the anti-theft system.............................................................................. 11B – 4
Antitheft system alarm operating conditions ........................................................ 11B – 4
Function of a keyless entry system ......................................................................... 11B – 4
Status LED ................................................................................................................. 11B – 4
Hazard relay ............................................................................................................... 11B – 4
Switches .................................................................................................................... 11B – 4
Receiver......................................................................................................................11B – 5
Range of communication ......................................................................................... 11B – 5
Diagnosis ................................................................................................................... 11B – 5
Transmitter (into remote key) .................................................................................. 11B – 5
Transmitter (into remote key) power ...................................................................... 11B – 5
Super lock .................................................................................................................. 11B – 5
No proper transmitter is available, what should be done for the system ?........ 11B – 6
DIAGRAMS AND SCHEMATICS ................................................................................... 11B – 7
SYSTEM WIRING DIAGRAMS .................................................................................. 11B – 7
COMPONENT WIRING LOCATORS (LHD) ............................................................... 11B – 8
WIRING DIAGRAM (LHD).......................................................................................... 11B – 9
WIRING DIAGRAM (LHD).......................................................................................... 11B – 10
WIRING DIAGRAM (LHD).......................................................................................... 11B – 11
WIRING DIAGRAM (LHD).......................................................................................... 11B – 12
WIRING DIAGRAM (RHD with keyless) ................................................................... 11B – 13
WIRING DIAGRAM (Super Lock).............................................................................. 11B – 14
WIRING DIAGRAM (Super Lock).............................................................................. 11B – 15
WIRING DIAGRAM (RHD) ......................................................................................... 11B – 16
WIRING DIAGRAM (RHD) ......................................................................................... 11B – 17
WIRING DIAGRAM (Super Lock).............................................................................. 11B – 18
WIRING DIAGRAM (Super Lock).............................................................................. 11B – 19
WIRING DIAGRAM (Super Lock).............................................................................. 11B – 20
Antitheft control unit (A) .......................................................................................... 11B – 21

11B – 2 ANTITHEFT SYSTEM
Pin-outs ......................................................................................................................11B – 21
Pin- Assignment ........................................................................................................ 11B – 22
lmportant information on Programming .................................................................... 11B – 23
Security code ............................................................................................................. 11B – 23
Entering a code ......................................................................................................... 11B – 23
Tech-2 Scan Tool............................................................................................................ 11B – 24
Tech-2 Features ......................................................................................................... 11B – 25
Getting Started ......................................................................................................... 11B – 25
Operating Procedure................................................................................................. 11B – 26
Menu ..........................................................................................................................11B – 27
DTC ............................................................................................................................. 11B – 27
Clear DTC Information .............................................................................................. 11B – 27
Tech-2 Data Display................................................................................................... 11B – 27
Actuator Test ............................................................................................................. 11B – 27
Unlock / Lock Test..................................................................................................... 11B – 27
Arm / Disarm Signal Test ......................................................................................... 11B – 28
Horn Signal Test ........................................................................................................ 11B – 28
Turn Signal Test......................................................................................................... 11B – 28
Theft LED Test ........................................................................................................... 11B – 28
Programming............................................................................................................. 11B – 29
Erase remote keys..................................................................................................... 11B – 29
Program Remote Keys .............................................................................................. 11B – 30
ProgramAntitheft Waring......................................................................................... 11B – 31
Program Country Code ............................................................................................. 11B – 32
Program Vehicle Options.............................................................................................. 11B – 33
Tech-2 Data List ......................................................................................................... 11B – 34
DIAGNOSIS .................................................................................................................... 11B – 35
Diagnostic procedure................................................................................................ 11B – 35
Clearing Diagnostic Trouble Codes ......................................................................... 11B – 35
Verifying Vehicle Repair............................................................................................ 11B – 35
Diagnostic Aids ......................................................................................................... 11B – 35
Check the condition for system parts ..................................................................... 11B – 35
Check the Electro-Magnetic Interference (EMI) ..................................................... 11B – 35
Check the other items .............................................................................................. 11B – 35
Check the operation.................................................................................................. 11B – 35
Diagnostic Trouble Code (DTC) list.......................................................................... 11B – 36
Antitheft System Check ........................................................................................... 11B – 37
No Antitheft Lamp .................................................................................................... 11B – 38
DTC13 Security code not yet programmed ............................................................ 11B – 39
DTC14 No remote key programmed ....................................................................... 11B – 40
DTC16 Door lock actuators short circuit to ground ............................................... 11B – 41

ANTITHEFT SYSTEM 11B – 3
Service Precaution
WARNING:
THIS VEHICLE HAS A SUPPLEMENTAL RESTRAINT SYSTEM (SRS). REFER TO THE SRS COMPONENT AND
WIRING LOCATION VIEW IN ORDER TO DETERMINE WHETHER YOU ARE PERFORMING SERVICE ON OR
NEAR THE SRS COMPONENTS OR THE SRS WIRING. WHEN YOU ARE PERFORMING SERVICE ON OR
NEAR THE SRS COMPONENTS OR THE SRS WIRING, REFER TO THE SRS SERVICE INFORMATION.
FAILURE TO FOLLOW WARNINGS COULD RESULT IN POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION:
Always use the correct fastener in the proper location. When you replace a fastener, use ONLY the exact
part number for that application. ISUZU will call out those fasteners that require a replacement after
removal. ISUZU will also call out the fasteners that require thread lockers or thread sealant. UNLESS
OTHERWISE SPECIFIED, do not use supplemental coatings (Paints, greases, or other corrosion inhibitors)
on threaded fasteners or fastener joint interfaces. Generally, such coatings adversely affect the fastener
torque and the joint clamping force, and may damage the fastener. When you install fasteners, use the
correct tightening sequence and specifications. Following these instructions can help you avoid damage
to parts and systems.
DTC20 Broken wire to door lock actuators ............................................................ 11B – 42
DTC21 Remote key 1 with random code out of capture range ............................ 11B – 43
DTC22 Remote key 2 with random code out of capture range ............................ 11B – 44
DTC23 Remote key 3 with random code out of capture range ............................ 11B – 45
DTC24 Remote key 4 with random code out of capture range ............................ 11B – 46
DTC25 Remote key 5 with random code out of capture range ............................ 11B – 47
DTC28 Input immobiliser short circuit to ground .................................................. 11B – 48
DTC29 Broken wire to immobiliser ......................................................................... 11B – 49
DTC31 Actuator driver door defect ......................................................................... 11B – 50
DTC32 Actuator passenger door defect .................................................................. 11B – 51
DTC36 Broken wire to driver door........................................................................... 11B – 52
DTC37 Broken wire to passenger door ................................................................... 11B – 53
DTC41 Driver door micro switch unlock defect ..................................................... 11B – 54
DTC42 Driver door micro switch lock defect .......................................................... 11B – 55
DTC43 Driver door micro switch dead lock defect ................................................ 11B – 56
DTC44 Passenger door micro switch lock defect................................................... 11B – 57
DTC45 Passenger door micro switch unlock defect .............................................. 11B – 58
DTC47 Battery voltage for door lock actuators is missing ................................... 11B – 59
DTC50 A/D converter defect or battery voltage less than 9 volt ......................... 11B – 60
DTC51 E E P ROM defect .......................................................................................... 11B – 61
DTC52 E E P ROM not programmed by ISUZU ...................................................... 11B – 62
DTC55 Control unit defect ........................................................................................ 11B – 63
DTC123 Output flasher short circuit to grpund or broken wire ........................... 11B – 64
DTC125 Output alarm horn broken wire ................................................................ 11B – 65

ANTITHEFT SYSTEM 11B – 7
DIAGRAMS AND SCHEMATICS
SYSTEM WIRING DIAGRAMS
M
M
M
M
M
M
M
M
- +
ANTITHEFT CONTROL UNIT BATTERY
(12V)
80A10A
ACC Ignition switch20A
10A
10A
antitheft horn
power supply
power supply
door lock motors
hazard relay(RH)
flashers(RH)
hazard relay(LH)
flashers(LH)
status LED
immobilizer controller
daiagnostc conector
groundlock lock
locklock lock alarm trigger
super lock
unlock unlock
(unlock)
(unlock)
unlock
driver door rear door(LH) rear door(RH)rear door(LH) rear door(RH)
assist door driver door assist doordriver door
assist door
driver door assist door
engine hood contact switch
door contact switch
auto door lock switch auto door lock
door lock cylinder
disarmwith super
lock without
super lock

11B – 8 ANTITHEFT SYSTEM
ANTI-THEFT INDICATER SIDE TURN SIGNAL , HAZARD
WARNING LIGHT ; RH
ANTI-THEFT HORN FRT TURN SIGNAL , HAZARD
WARNING LIGHT ; RH
ENGINE HOOD SWANTI-THEFT
CONTROLLERRR DOOR SW ; RH
FRT DOOR LOCKACTUATOR ; RHFRT DOOR KEY SW ; RHFRT DOOR SW ; RH
RR DOOR LOCK ACTUATOR ; RHFRT DOOR SW ; LH
RR DOOR LOCK ACTUATOR ; LH RR DOOR SW ; LH
FRT DOOR LOCKACTUATOR ; LHFRT DOOR KEY SW ; LH
SIDE TURN SIGNAL , HAZARD
WARNING LIGHT ; LH FRT TURN SIGNAL , HAZARD
WARNING LIGHT ; LHRELAY ; HAZARD
RR TURN SIGNAL , HAZARD
WARNING LIGHT ; LH
RAW4C0XF000201
COMPONENT WIRING LOCATORS (LHD)