2004 ISUZU TF SERIES clutch

FRONT WHEEL DRIVE 4C1-57
FRONT HUB AND DISC
(4




4 Manual Locking Hub Model)
DISASSEMBLY
Refer to SECTION 3E “WHEEL AND TIRE” for wheel removal procedure



RTW440LF000301

Disassembly Steps


1. Bolt
2. Cover assembly
3. Snap ring and shim
4. Body assembly
5. Lock washer


6. Hub nut


7. Hub and disc assembly
8. Outer bearing
9. Oil seal
10. Inner bearing
11. ABS sensor rotor


12. Bolt


13. Wheel pin




14. Clutch assembly
15. Snap ring
16. Knob
17. Compression spring
18. Follower


19. Retaining spring
20. X-ring
21. Snap ring
22. Inner assembly
23. Snap ring
24. Ring
25. Spacer

4C1-58 FRONT WHEEL DRIVE



Important Operations
1. Bolt
Before removal, shift transfer lever into “2H” position and set
free wheeling hub knob into “FREE” position.


6. Hub nut
Wrench : 5-8840-2117-0
(J-36827)



7. Hub and disc assembly
Before disassembly, remove the disc brake caliper assembly
and hang it on the frame with wires.
Refer to Section “Brake” for disc brake caliper removal
procedure.


14. Clutch Assembly
While pushing follower knob, turn clutch assembly clockwise
and then remove clutch assembly from knob.



19. Retaining Spring
Remove retaining spring from clutch assembly by turning it
counterclockwise.

4C1-60 FRONT WHEEL DRIVE
INSPECTION AND REPAIR
Make necessary correction or parts replacement if wear, damage or any other abnormal conditions are found
through inspection.
For inspection and servicing of disc caliper, and relative parts, and ABS parts, refer to Section Brakes.




Hub

Hub bearing, oil seal


Knuckle spindle


Disc


Caliper


ABS sensor rotor


Cap, Hub flange, Shim, Snap ring


Free wheeling hub parts (Option)

Clutch, Knob, follower, inner, ring and
spring


Visual Check
Check the following parts for wear, damage or other abnormal
conditions.

FRONT WHEEL DRIVE 4C1-61
REASSEMBLY
Refer to SECTION 3E “WHEEL AND TIRE” for wheel removal procedure.


RTW440LF000401


Reassembly Steps


1. Spacer
2. Ring
3. Snap ring


4. Inner assembly
5. Snap ring
6. X-ring


7. Knob


8. Snap ring


9. Retaining spring


10. Follower


11. Compression spring


12. Clutch assembly




13. Wheel pin


14. Bolt


15. ABS sensor rotor


16. Inner bearing


17. Oil seal


18. Outer bearing


19. Hub and disc assembly


20. Hub nut


21. Lock washer


22. Body assembly


23. Snap ring and shim


24. Cover assembly


25. Bolt

4C1-62 FRONT WHEEL DRIVE



Important Operations
1. Spacer
Apply grease to both faces of spacer.
4. Inner Assembly
Apply grease wheel bearing to inside face of ring.
g(oz)
Amount of grease 6 (0.21)


7. Knob
(1) Apply grease Wheel bearing to outer circumference of knob
and inner circumference of cover.
(2) Align detent ball to either groove of cover.




8. Snap Ring
Turn the smoother face to knob side.
9. Retaining Spring
Align the end of spring to the end of cut portion of clutch spring
groove.


10. Follower
Install follower to clutch so that follower nail will come closer to
the bent portion of retaining spring by aligning follower stopper
nail to outer teeth of clutch. Then, hook retaining spring onto
upper portion of hanger nails of follower.




11. Compression Spring
Turn the smaller diameter side to follower.
12. Clutch Assembly
Align follower nail to handle groove, and then assemble clutch
with knob by pushing and turning clutch counterclockwise to
knob.

4C2-4 SHIFT ON THE FLY SYSTEM
Shift On The Fly System and Association Parts







RTW440LF000701
Disassembly steps
1. Filler plug
2. Bolt
3. Front axle drive shaft (LH side)
4. Bolt
5. Actuator assembly
6. Bolt
7. Housing
8. Sleeve
9. Clutch gear
10. Snap ring
11. Inner shaft
12. Snap ring
13. Inner shaft bearing
14. Needing bearing
15. Oil seal
Reassembly steps
To reassemble, follow the disassembly steps in
the reverse order.

SHIFT ON THE FLY SYSTEM 4C2-5



DISASSEMBLY
1. Filler Plug
Remove filler plug and packing and drain oil.
2. Bolt
Loosen mounting bracket fitting bolts and remove front axle
drive shaft from front axle case.
3. Front Axle Drive Shaft (LH side)
4. Bolt
Loosen actuator ASM fitting bolts.
5. Actuator Assembly
Draw out actuator ASM.
6. Bolt
Remove hosing fitting bolts.
7. Housing
8. Sleeve
9. Clutch Gear



412RW017

10. Snap Ring
Remove snap ring from front axle case by using a snap ring
pliers.

11.Inner Shaft
Take out inner shaft from front axle case.



412RW016

12.Snap Ring
Remove snap ring from inner shaft by using a snap ring
pliers.



412RW015
13.Inner Shaft Bearing
Remove inner shaft bearing by using a special tool and
press.
Remove : 5-8840-2197-0 (J-37452)
NOTE:
Be careful not to damage the shaft.

SHIFT ON THE FLY SYSTEM 4C2-7



RTW440SH000101
Inner Shaft Bearing
Inspect the state of inner shaft bearing. If any abnormality
such as smoothlessness is found, replace with a new inner
shaft bearing.
Insert a clutch gear and check the state of needle bearing.
If there is an abnormality such as smoothlessness, replace
the needle bearing.

Sleeve
Visual Check
Check and see that there is not wear, damage, or crecking
in the sleeve.
NOTE:
Close inspection of the groove and inner gear are required
because those are important parts.










412RW011
Functional Check
Operate the sleeve with the inner shaft combined with the
clutch gear.
If smoothlessness is felt, replace the sleeve.
NOTE:
Gear oil should be applied to the contact surface of gear.




412RW022
Dimensional Check
Check the width of sleeve center groove.
Sleeve Center Groove (Limit) mm (in)
7.1 (0.28)