2004 ISUZU TF SERIES wheel bolts

6A – 38 ENGINE MECHANICAL
6. Front propeller shaft (for 4x4 model)
Remove the spline yoke flange bolt at the transfer output
shaft.
Do not allow the spline yoke to fall away from the front
propeller shaft.
If the spline yoke should fall away from the front propeller
shaft, align the setting marks on the spline yoke and the
propeller shaft to reassemble the two marks. The setting
marks are punched circles approx. 3mm (0.12 in) in
diameter.

7. Clutch slave cylinder (for M/T model)
8. ATF pipe (for A/T model)
9 Shift control cable (for A/T model)
10. Transmission sensor harness
Remove the vehicle speed sensor connector, inhibitor
switch connector (A/T), ATF temperature sensor
connector, back up light switch connector (M/T) from
transmission.
11. Breather hose (for A/T model)
12. Transmission shift lever (for M/T model)
Remove the shift lever from the floor.
13. Transfer shift lever (for 4x4 model)
Remove the shift lever from the floor.

14. Transmission member
1) Support the transmission with the transmission jack.
2) Remove the transmission member mounting bolts
fixing the transmission member to the chassis frame.


15. Torque converter bolt (for A/T model)
1) Remove the under cover under the torque converter
housing.
2) Rotate the flywheel by using tire lever or some other
tool, and then remove the torque converter bolts.
16. Transmission coupling bolt
1) Support the engine with the garage jack.
2) Use the jack to slightly lower the transmission.
3) Remove the transmission coupling bolts.
17. Transmission (and transfer)
Separate the transmission (and transfer) from the
engine.Take care not to damage the transmission, the
engine, and their related parts..

F06R300007 P1010025

6A – 52 ENGINE MECHANICAL


RTW36ASH000801
Idler Gear "A" End Play Measurement
Insert a feeler gauge between the idler gear and the thrust
collar to measure the gap and determine the idler gear
end play.
If the measured value exceeds the specified limit, the
thrust collar must be replaced.

Idler Gear End Play mm (in)
Standard Limit
0.07 (0.0028) 0.2 (0.0079)





4JA1T(L)
040R300009
14. Idle Gear Shaft
15. Crankshaft Timing Gear



4JA1TC/4JH1TC RTW36ASH001301
16. Injection Pump
1. Remove the injection pump cover (4JA1TC/4JH1TC
only).
2. Remove the injection pump bracket.
3. Pull the injection pump along with the injection pump
timing gear free toward the rear of the engine.

NOTE:
Plug the injection pump delivery ports with the caps to
prevent the entry of foreign material.









17. Flywheel
Loosen the flywheel bolts in numerical order a little at a
time.
Use the gear stoper to stop the flywheel gear.
Gear stoper: 5-8840-0214-0

18. Crank Case

19. Oil Pump With Oil Pipe

015RY00001

6A – 110 ENGINE MECHANICAL









17. Cylinder Body Rear Plate
1. Align the rear plate with the cylinder body knock pins.
2. Tighten the rear plate to the specified torque.


Rear Plate Torque N·m(kg·m/lbft)
82 (8.4/61)














18. Flywheel
1. Apply a coat of engine oil to the threads of the flywheel
bolts.
2. Align the flywheel with the crankshaft dowel pin.
3. Tighten the flywheel bolts in the numerical order shown
in the illustration.
Gear stoper: 5-8840-0214-0


Flywheel Bolt Torque N·m(kg·m/lbft)
118 (12/87)











19. Crankshaft Timing Gear
Use the crankshaft timing gear installer (1) to install the
crankshaft timing gear (2).
The crankshaft timing gear setting mark must be facing
outward.
Crankshaft Timing Gear Installer: 9-8522-0020-0


















20. Idler Gear Shaft
21. Idler Gear "A"
1. Turn the crankshaft clockwise to set the DTC of the
No.1 piston.
2. Apply engine oil to the idler gear and the idler gear
shaft.
The idler gear shaft oil hole (A) must be facing up.
3. Position the idler gear setting marks so that they are
facing the front of the engine.


015LX113 020R100001
020RY00034
020RY00035

ENGINE MECHANICAL 6A – 115



RTW46ASH002201




















4JA1T(L):
4. Tighten the injection pump bolts to the specified torque.
5. Install the injection pump bracket (4) and the bracke
t
bolts (5) and (6) to the cylinder body. Temporarily tighten
the bracket bolts.
6. Tighten the bracket bolts (5) to the specified torque.
7. Tighten the bracket bolts (6) to the specified torque.


Injection pump Bracket Bolt Torque (6) N·m(kg·m/lbft)
19 (1.9/14)

Injection pump Bracket Bolt Torque (5) N·m(kg·m/lbft)
40 (4.1/30)



030RY00007














24. Water Pump
1. Apply the recommended liquid gasket or its equivalent
to the water pump at the position shown in the
illustration.
Do not apply an excessive amount of liquid gasket.
2. Tighten the water pump bolts to the specified torque.


Water Pump Bolt Torque N·m(kg·m/lbft)
20 (2.0/14)













25.Timing Gear Case Cover
1.
Align the gear case with the timing gear case knock pin
and then install the timing gear case cover.
2. Tighten the gear case cover bolts to the specified
torque.


Gear Case Cover Bolt Torque N·m(kg·m/lbft)
M8 19 (1.9/14)
M12 76 (7.7/56)

























26. Crankshaft Damper Pulley
Tighten the crankshaft damper pulley bolt to the specified
torque.
Note:
Hold the flywheel ring gear stationary to prevent the
crankshaft from turning when tightening the damper
pulley bolt.


Crankshaft Damper Pulley Bolt Torque N·m(kg·m/lbft)
206 (21/152)
Take care not to damage the crankshaft damper pulley
boss.


014R100014 020R300004

ENGINE MECHANICAL (6VE1 3.5L) 6A-3
General Description
Engine Cleanliness And Care
An automobile engine is a combination of many
machined, honed, polished and lapped surfaces with
tolerances that are measured in the thousandths of a
millimeter (ten thousandths of an inch). Accordingly,
when any internal engine parts are serviced, care and
cleanliness are important. Throughout this section, i
t
should be understood that proper cleaning and
protection of machined surfaces and friction areas is
part of the repair procedure. This is considered
standard shop practice even if not specifically stated.


A liberal coating of engine oil should be applied to
all friction areas during assembly to protect and
lubricate the surfaces on initial operation.

Whenever valve train components, pistons, piston
rings, connecting rods, rod bearings, and
crankshaft journal bearings are removed fo
r
service, they should be retained in order.


At the time of installation, they should be installed
in the same locations and with the same mating
surfaces as when removed.

Battery cables should be disconnected before any
major work is performed on the engine. Failure to
disconnect cables may result in damage to wire
harness or other electrical parts.

The six cylinders of this engine are identified by
numbers; Right side cylinders 1, 3 and 5, Left side
cylinders 2, 4 and 6, as counted from crankshaf
t
pulley side to flywheel side.
General Information on Engine Service
The following information on engine service should be
noted carefully, as it is important in preventing damage
and contributing to reliable engine performance.

When raising or supporting the engine for any
reason, do not use a jack under the oil pan. Due to
the small clearance between the oil pan and the oil
pump strainer, jacking against the oil pan may
cause damage to the oil pick-up unit.

The 12-volt electrical system is capable o
f
damaging circuits. When performing any work
where electrical terminals could possibly be
grounded, the ground cable of the battery should
be disconnected at the battery.


Any time the intake air duct or air cleaner is
removed, the intake opening should be covered.
This will protect against accidental entrance o
f
foreign material into the cylinder which could
cause extensive damage when the engine is
started.
Cylinder Block
The cylinder block is made of aluminum die-cast casting
for 75Vtype six cylinders. It has a rear plate integrated
structure and employs a deep skirt. The cylinder liner is
cast and the liner inner diameter and crankshaft journal
diameter are classified into grades. The crankshaft is
supported by four bearings of which width is differen
t
between No.2, No.3 and No.1, No.4; the width of No.3
bearing on the body side is different in order to suppor
t
the thrust bearing. The bearing cap is made of nodular
cast iron and each bearing cap uses four bolts and two
side bolts.
Cylinder Head
The cylinder head, made of aluminum alloy casting
employs a pent-roof type combustion chamber with a
spark plug in the center. The intake and exhaust valves
are placed in V-type design. The ports are cross-flo
w
type.
Valve Train
Intake and exhaust camshaft on the both side of banks
are driven through an camshaft drive gear by timing
belt. The valves are operated by the camshaft and the
valve clearance is adjusted to select suitable thickness
shim.
Intake Manifold
The intake manifold system is composed of the
aluminum cast common chamber and intake manifold
attached with six fuel injectors.
Exhaust Manifold
The exhaust manifold is made of nodular cast iron.
Pistons and Connecting Rods
Aluminum pistons are used after selecting the grade
that meets the cylinder bore diameter. Each piston has
two compression rings and one oil ring. The piston pin
made of chromium steel is offset 1mm toward the thrus
t
side, and the thrust pressure of piston to the cylinder
wall varies gradually as the piston travels. The
connecting rods are made of forged steel. The
connecting rod bearings are graded for correct size
selection.
Crankshaft and Bearings
The crankshaft is made of Ductile cast-iron. Pins and
journals are graded for correct size selection for thei
r
bearing.
Engine Control Module (ECM)
The ECM location is on the common charmber.

6A-44 ENGINE MECHANICAL (6VE1 3.5L)
1. Remove engine assembly.

Refer to removal procedure for Engine
Assembly in this manual.
2. Remove timing belt.

Refer to removal procedure for Timing Belt in
this manual.
3. Remove oil pan and crankcase.

Refer to removal procedure for Oil Pan and
Crankcase in this manual.
4. Remove oil pipe with O-ring.
5. Remove oil strainer assembly with O-ring.
6. Remove oil pump assembly.

Refer to removal procedure for Oil Pump in this
manual.
7. Remove cylinder body side bolts.
8. Remove oil gallery.
9. Remove flywheel.
10. Remove rear oil seal retainer.

Refer to removal procedure for Rear Oil Seal in
this manual.
11. Remove connecting rod caps.
12. Remove crankshaft main bearing caps.
13. Remove crankshaft and main bearings.
Installation
1. Install crankshaft and main bearings.

Install main bearing in the cylinder block and
main bearing cap respectively.

Apply new engine oil to upper and lower main
bearings.
NOTE:

Do not apply engine oil to the bearing back faces.

Make sure that main bearings are in correc
t
position.

Install crankshaft with care.

Apply engine oil to the thrust washer.

Install thrust washer on No.3 journal.

Oil grooves in thrust washer must face the
crankshaft.





015RS012



015RS013
2. Install crankshaft main bearing caps.


Apply engine oil to the thread and seating
surface of each bearing cap fixing bolt.
NOTE:

Do not apply engine oil to the bearing back faces.

Install bearing caps in the order of numbers,
starting with cylinder block front side.

Tighten main bearing fixing bolts to the specified
torque.
Torque: 39 N




m (4.0 kg




m/29 lb ft)


After tightening the bolts, make sure that the
crankshaft rotates smoothly.
3. Install connecting rod caps.

The cap number must be same as connecting
rod number.


Apply engine oil to the thread and seating
surface of each nut.

ENGINE MECHANICAL (6VE1 3.5L) 6A-45

Tighten nuts to the specified torque.
Torque: 54 N




m (5.5 kg




m/40 lb ft)


After tightening the nuts, make sure that the
crankshaft rotates smoothly.
4. Install rear oil seal retainer.

Remove oil on cylinder block and retainer fitting
surface.


Apply sealant (TB1207B or equivalent) to
retainer fitting surface as shown in illustration.

The oil seal retainer must be installed within 5
minutes after sealant application to preven
t
premature hardening of sealant.




015RW002
Legend
(1) Around Bolt Holes
(2) Around Dowel Pin


Apply engine oil to oil seal lip and align a dowel
pin hole in the cylinder block with that in the
retainer.

Tighten retainer fixing bolts to the specified
torque.
Torque: 18 N




m (1.8 kg




m/13 lb ft)




015RW001
5. Install flywheel.

Clean tapped holes in the crankshaft.

Remove oil on crankshaft and flywheel fitting
surface.
NOTE:

Do not reuse the bolts.

Do not apply oil or thread lock to the bolts.

Tighten fixing bolts to the specified torque.
Torque: 54 N




m (5.5 kg




m/40 lb ft)


015RS018

6A-48 ENGINE MECHANICAL (6VE1 3.5L)
Rear Oil Seal
Removal
1. Remove transmission assembly.

See Transmission section in this manual.
2. Remove flywheel.
3. Remove rear oil seal using a seal remover.
NOTE: Take care not to damage the crankshaft or oil
seal retainer when removing oil seal.
Installation
1. Apply engine oil to oil seal lip and install oil seal
using 5884022860.




015RS017
2. Install flywheel.

Clean tapped holes in the crankshaft.

Remove oil on the crankshaft and flywheel
mounting surface.

Tighten fixing bolts to the specified torque.
NOTE: Do not reuse the bolts and do not apply oil o
r
thread lock to the bolts.
Torque: 54 N




m (5.5 kg




m/40 lb ft)


015RS018
3. Install transmission.

See Transmission section in this manual.
CAUTION: When assembling the engine and
transmission, confirm that dowels have been
mounted in the specified positions at the engine
side. Take care that dowel positions are different
between the manual transmission and the
automatic transmission. Otherwise, the
transmission may be damaged.






012RS009