2004 ISUZU TF SERIES wheel bolts

FRONT WHEEL DRIVE 4C1-43
Important Operations
Before removal, jack up the front of vehicle and support frame
with jack stands.



2. Brake Caliper
(1) Remove the two bolts from the rear side of the knuckle arm,
then remove the brake caliper, with the brake hose
attached.
(2) Use a wire etc., for attaching the brake caliper to the uppe
r
link.
Refer to the section Brake.



3. Hub Cap
When removing hub cap, exercise care so as not to scratch or
distort hub fitting face.



9. Hub and Disc Assembly
Using a brass bar to remove the outer bearing outer race (1),
oil seal, inner bearing and inner bearing outer race (2) from the
hug.



If necessary, replace the wheel pin in the following manner.

13. Bolt
14. Wheel Pin ; Front Hub
(1) Scribe mark on hub to disc before disassembly to insure
proper assembly.
(2) Drive out the ABS sensor rotor using a metal bar and
hammer through the two bolt holes.

Discard the used ABS sensor rotor
Refer to the section Brake.

4C1-44 FRONT WHEEL DRIVE


(3) Clamp hub and disc assembly in vise using protective pads
and remove six (6) disc to hub retaining bolts.



(4) Place hub on a suitable work surface and remove wheel
studs, as required, using a hammer.

FRONT WHEEL DRIVE 4C1-51

Important Operations
6. Hub nut
Wrench : 5-8840-2117-0
(J-36827)



7. Hub and disc assembly
Before disassembly, remove the disc brake caliper assembly
and hang it on the frame with wires.
Refer to Section “Brake” for disc brake caliper removal
procedure.


12. Bolt
13. Wheel Pin ; Front Hub
(1) Scribe mark on hub to disc before disassembly to insure
proper assembly.
(2) Drive out the ABS sensor rotor using a metal bar and
hammer through the two bolt holes.
 Discard the used ABS sensor rotor
Refer to the section Brake.



(3) Clamp hub and disc assembly in vise using protective pads
and remove six (6) disc to hub retaining bolts.


(4) Place hub on a suitable work surface and remove wheel
studs, as required, using a hammer.

FRONT WHEEL DRIVE 4C1-59


12. Bolt
13. Wheel Pin ; Front Hub
(1) Scribe mark on hub to disc before disassembly to insure
proper assembly.
(2) Drive out the ABS sensor rotor using a metal bar and
hammer through the two bolt holes.

Discard the used ABS sensor rotor
Refer to the section Brake.



(3) Clamp hub and disc assembly in vise using protective pads
and remove six (6) disc to hub retaining bolts.


(4) Place hub on a suitable work surface and remove wheel
studs, as required, using a hammer.

ANTI-LOCK BRAKE SYSTEM 5B-7

Electronic Hydraulic Control Unit
Electronic Hydraulic Control Unit and Associated Parts



RHD model LHD model
350R300001-X

Legend


1.
Flare Nut from master cylinder front

2.
Flare Nut to front right wheel cylinder

3. Flare Nut to front left wheel cylinder

4.
Flare Nut to rear wheel cylinder


5.
Electronic Hydraulic Control Unit (EHCU)

6.
Flare Nut from master cylinder rear

7.
Bolt

8.
Front

Removal
1. Disconnect the harness connector.
2. Loosen five flare nuts and remove brake pipes.


After disconnecting brake pipe, cap or tape the
openings of the brake pipe to prevent the entry o
f
foreign matter.
3. Remove three bracket fixing bolts.

Installation
1. Install EHCU and tighten the bolt to the specified
torque.

Torque : 8 N
m (0.8 kg
m /69 lb in)
2. Tighten the flare nuts to the specified torque.

Torque : 16 N
m (1.6 kg
m /12 lb ft)

3. Connect the harness connector.

ANTI-LOCK BRAKE SYSTEM 5B-11

Rear Wheel Speed Sensor
Rear Wheel Sensor and Associated Parts
420R300008
Legend


1.
Rear Speed Sensor Assembly

2.
Bolt : cable to frame

3.
Connector

4. Bolt : sensor to rear axle


5.
Speed Sensor

6. Bolt : cable to axle

7.
Bolt : sensor to rear axle

8.
Speed Sensor

Removal
1. Disconnect the harness connector (3).
2. Remove the cable fixing bolt (2)(6).
3. Disconnect the cable fixing clips (arrow marked).
4. Remove the speed sensor fixing bolts (4)(7) and
speed sensor (5)(8).

Inspection and Repair
1. Check speed sensor head for presence of foreign
materials; remove any dirt, etc.
2. Check the head for damage, and replace speed
sensor if necessary.

ANTI-LOCK BRAKE SYSTEM 5B-13

Front Speed Sensor Rotor
Front Sensor Rotor and Associated Parts
411R300010
Legend


1.
Sensor Rotor

2.
Hub and Disc


3.
Disc Rotor fixing Bolt

4. Hub and Disc Assembly

Removal
1. Remove the hub and disc assembly (4). (Refer to
the section Front wheel Drive).
2. Remove two disc rotor fixing bolts (3) on a diagonal.
3. Drive out the sensor rotor using a metal bar and
hammer through the two bolt holes.


Discard the used sensor rotor.
4. Install disc rotot fixing bolts and tighten them to the
specified torque.

Torque : 103 N
m (10.5 kg
m /76 lb ft)

CAB 10-29

Important Operations
1. Front Console Assembly


Refer to Floor Consol in this section.



2. Glove Box


Remove 2 fixing screws and pulling the handle.



3. Instrument Panel Driver Lower Cover Assembly
1) Remove the engine hood opener 2 fixing screws.
2) Remove the lower cover one fixing screw.
3) Pull out the cover (Stick type parking brake only).
4) Pull out the lower cover assembly.




4. Driver Knee Bolster Assembly


Remove 4 fixing bolts.
Caution:
For precaution on installation or removal of SRS-air bag
system, refer to section 9 “Supplemental Restraint System
(SRS) - AIR BAG”

5. Driver Air Bag
6. Steering Wheel/Steering Cowl


Refer to Section 3B “STEERING COLUMN” for steering
lock assembly removal steps.




7. Meter Cluster Assembly


Pull out the 4 clip positions.