2004 ISUZU TF SERIES wheel bolts

0B-10 MAINTENANCE AND LUBRICATION




I : Inspect and correct or replace as necessary A : Adjust
R : Replace or change T : Tighten to specified torque L : Lubricate
SERVICE INTERVAL:
1,000 km 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100(Use odometer reading or
1,000 miles 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60months whichever comes
fi rst)
or months 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
SERVICE BRAKES Brake fluid - - - - - - - I - - - - - - - I - - - - Brake system for fluid leakage - - - I - - - I - - - I - - - I - - - I Brake function - - - I - - - I - - - I - - - I - - - I * Front Disc brake pads and discs wear - - - I - - - I - - - I - - - I - - - I * Rear brake lining and drum wear - - - I - - - I - - - I - - - I - - - I Brake pedal travel and play - - - I - - - I - - - I - - - I - - - I Pipes and hoses for loose
connections or damage - - - I - - - I - - - I - - - I - - - I
PARKING BRAKE Parking brake function - - - I - - - I - - - I - - - I - - - I Parking brake lever travel - - - I - - - I - - - I - - - I - - - I Cables for looseness or damage and
guide for damage
-
-
-
I
-
-
-
I
-
-
-
I
-
-
-
I
-
-
-
-
Ratchet for wear or damage - - - I - - - I - - - I - - - I - - - I SUSPENSION Leaf/Coil/Torsion bar springs for
damage - - - I - - - I - - - I - - - I - - - I
Mount for looseness or damage - - - I - - - I - - - I - - - I - - - I Shock absorbers for oil leakage - - - I - - - I - - - I - - - I - - - I Shock absorbers mount for
looseness - - - I - - - I - - - I - - - I - - - I
Rubber bushes of suspension wear
or damage - - - I - - - I - - - I - - - I - - - I
Spring action for loss of balance due
to weakening - - - - - - - - - - - I - - - - - - - -
Joi nt ball rubber boot for damage - - - I - - - I - - - I - - - I - - - I WHEELS Wheel nuts - - - T - - - T - - - T - - - T - - - T Wheel disc for damage - - - I - - - I - - - I - - - I - - - I Hub bearing grease - - - - - - - R - - - - - - - R - - - - Front and rear hub bearings for
looseness - - - I - - - I - - - I - - - I - - - I
Tire pressure and damage I - - I - - - I - - - I - - - I - - - I Tire rotation (Rotate as required) OTHERS Bolts and nuts on chassis and body - - - I - - - I - - - I - - - I - - - I Lube front free - wheeling hubs - - - - - - - L - - - - - - - L - - - -

POWER-ASSISTED STEERING SYSTEM 3B-59

Check clearance between capsule and bracket. If must
be within 1mm (0.039 in).
431RW031

Column Universal Joint (between the
power steering unit and the steering shaft)
If the resistance is felt when checked by rotate the joint,
replace the lower second steering shaft.

Shaft Universal Joint (between the lower
second steering shaft and the second
steering shaft)
If the resistance is felt when checked by rotate the joint,
replace the second steering shaft assembly.

Tilt Mechanism
Tilt mechanism should moves smoothly.
While locked the tilt mechanism, be sure the steering
column latch securely by pushing the steering wheel
upward and downward.

Installation
1. Align the setting marks on the second steering shaft
and the steering column assembly (applied at
disassembly).
2. Connect the steering column assembly to the second
steering shaft. Tighten the bolts to the specified
torque.
Torque: 26 - 36 N




m (2.7 – 3.7 kg




m/20 - 27 lb ft)
3. Thread the steering column assembly through the
hole in the dashpanel. Temporarily tighten the
steering column and the second steering shaft fixing
bolt.
4. Connect the lower second steering shaft and the
second steering shaft. Tighten the universal joint
bolts to the specified torque.
Torque: 26 - 36 N




m (2.7 – 3.7 kg




m/20 - 27 lb ft)
5. Tighten the steering column fixing bolt (pedal brkt
side) to the specified torque (This bolt was
temporarily tighten in Step 3).
Torque: 18 -23 N




m (1.8 – 2.3 kg




m/13 - 17 lb ft)

6. Tighten the second steering shaft fixing bolt to the
specified torque (This bolt was temporarily tightened
in Step 3)
Torque: 18 -23 N




m (1.8 – 2.3 kg




m/13 - 17 lb ft)
7. Tighten the steering column fixing bolt (dashpanel
side) to the specified torque (This bolt was
temporarily tighten in Step 3).
Torque: 18 -23 N




m (1.8 – 2.3 kg




m/13 - 17 lb ft)
8. Install combination switch and SRS coil assembly.
After installation of combination switch assembly,
connect the combination switch wiring harness
connector and the SRS 2-way connector located
under the steering column.

3B-60 POWER-ASSISTED STEERING SYSTEM

9. Turn the SRS coil counter clockwise to full, return
about 3 turns and align the neutral mark. (with SRS
air bag)
CAUTION: When turning the SRS coil counte
r
clockwise to full, stop turning if resistance is felt.
Forced further turning may damage to the cable in
the SRS coil.
826RW014
10. When installing the steering column cover, be sure to
route each wire harness as illustrated so that the
harnesses do not catch any moving parts.
825RW017
Legend
(1) Steering Column Cover
(2) Starter Switch Harness
(3) Combination Switch Harness
(4) Inflator Module Harness

11. Install steering wheel and align the setting marks
made when removing.
Refer to the adjustment method in case a mark is
not attached in this section.
NOTE: Confirm SRS and Horn harness connector is
fixed by the steering wheel.
RTW33BSH000601

CAUTION: Never apply force to the steering wheel in
direction of the shaft by using a hammer or othe
r
impact tools in an attempt to remove the steering
wheel. The steering shaft is designed as an energy
absorbing unit.
12. Tighten the steering wheel fixing nut to the specified
torque.
Torque: 31 - 39 N




m (3.2 – 4.0 kg




m/23 - 29 lb ft)
13. Support the module and carefully connect the
module connector and horn lead, then install inflato
r
module.
NOTE: Pass the lead wire through the tabs on the
plastic cover (wire protector) of inflator to prevent lead
wire from being pinched.
14. Tighten bolts to specified torque.
Torque: 2 - 4 N




m (0.2 – 0.4 kg




m/17 - 35 lb in)
15. Install driver knee bolster (reinforcement).
16. Install instrument panel lower cover.
17. Install the engine hood opening lever.
18. Connect the yellow 2-way SRS connector and horn
lead located under the steering column.
19. Connect the battery "-" terminal cable. (with SRS ai
r
bag)

FRONT SUSPENSION 3C-7
4





2 (High Ride Suspension) and 4





4 Model
RTW340LF000801

The links attach to the vehicle with bolts and bushings at their inner pivot points and to the steering knuckle, which
is part of the front wheel spindle, at their outer points.
The knuckle is mounted to the upper and lower links each of which has a ball joint to permit pivoting of the knuckle
for steering operations. The hub is supported in position on the knuckle spindle by means of the two bearings and
the rotor is mounted to the hub.
The front suspension is an independent type utilizing torsion bar springs (4
4, 4
2 (High ride suspension)) and coil
springs (4
2 (Except High ride suspension)). The torsion bar spring has splines on each end. Height control is
provided on the third crossmember. Both the upper and lower links are pressed steel and the torsion bar is
supported at the ends by lower link in front and by height control arm in rear.

3C-60 FRONT SUSPENSION
Checkpoint Trouble Cause Countermeasure

Steering linkage and steering
gearReplaceWorn
AdjustImproper OK
NG NG
OKTire pressure Continued from the previous page
Steering unit fixing bolts and
linkageRetightenLoose
Adjust or replaceIncorrect adjustment or
abrasion OK
NG NG
OKFront wheel bearing
Lubricating oil and grease to
steering linkageReplaceInsufficient NG OK

WHEELS AND TIRES 3E-1

SECTION 3E
WHEELS AND TIRES
TABLE OF CONTENTS
PAGE
Main Data and Specifications ........................................................................................... 3E- 2
Torque Specifications ....................................................................................................... 3E- 3
Special Parts Fixing Nuts and Bolts ............................................................................ 3E- 3
Wheels and Tires ...............................................................................................................3E- 4
General Description ...................................................................................................... 3E- 4
Servicing ........................................................................................................................ 3E- 6
Disassembly and Reassembly ..................................................................................... 3E- 7
Inspection and Repair................................................................................................... 3E- 8
Troubleshooting ................................................................................................................3E- 10

WHEELS AND TIRES 3E-3

TORQUE SPECIFICATIONS
SPECIAL PARTS FIXING NUTS AND BOLTS
WHEELS AND TIRES
kgf

m (lb

ft/N

m)

7A3-6 ON-VEHICLE SERVICE (JR405E)
INHIBITOR SWITCH
The inhibitor switch is attached to the right side of the
transmission.

Inspect
1. Block the wheels.
2. Disconnect the negative battery cable.
3. Disconnect the harness connectors.
4. Use a ohmmeter to check the inhibitor switch
continuity between the following terminals as shown
in figure.
5. Place the select lever in the “N” range.
249R300001
6. Move the select lever to either side.
Check the inhibitor switch continuity between the
terminals shown in Step (4).
The continuity readings should remain fairly steady
as the select lever is moved.
If there is no continuity or the continuity is
intermittent, the inhibitor switch must be adjusted.

Adjust
1. Disconnect the shift calbe from the lever.
2. Loosen the inhibitor switch bolts.
3. Use the inhibitor switch set plate to align the neutral
holes (manual shaft and inhibitor switch).
Turn the inhibitor switch to adjust it.
Inibitor switch set plate: 5-8840-2763-0
Note:
Inhibitor switch adjustment is very important.
If the inibitor switch is not correctly adjusted, the
automatic transmission will not function normally.



4. Tighten the 2 inhibitor switch bolts to the specified
touque.
Torque: 5.5 N·m (48 lb·in)
47INH-SW01
5. Connect the shift cable to the lever.
6. Connect the harness connector.

Remove or Disconnect
1. Remove the cable bracket (1) from the transmission.
2. Disconnect the shift cable (2) from the lever (3).
3. Disconnect the harness connectors.
4. Remove the inhibitor switch bolts.
5. Remove the inhibitor switch (4) from the
transmission.

238R300001