2004 ISUZU TF SERIES key

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-7

TCM Voltage & Resistance Check Sheet
CHECK ITEM PIN No. VALUE NOTE
VIGN A6 –A1 VIGN
Key “ON ”

A6 –A23 VIGN
Key “ON ”
Backup Power Supply A24 –A1 +B (Always)
Key “ON ”
Inhibitor (Select) SW P B20 –A1 “P ” Range VIGN Key “ON ”

Except “P ” 0V
Inhibitor (Select) SW R B1
–A1 “R ” Range VIGN Key “ON ”

Except “R ” 0V
Inhibitor (Select) SW N B8
–A1 “N ” Range VIGN Key “ON ”

Except “N ” 0V
Inhibitor (Select) SW D B7
–A1 “D ” Range VIGN Key “ON ”

Except “D ” 0V
Inhibitor (Select) SW 2 B19
–A1 “2 ” Range VIGN Key “ON ”

Except “2 ” 0V
Inhibitor (Select)SW 1 B18
–A1 “1 ” Range VIGN Key “ON ”

Except “1 ” 0V
Inhibitor (Select) SW 3 B9
–A1 “3 ” Range VIGN Key “ON ”

Except “3 ” 0V
Power SW B13
–A1 ON 0V Key “ON ”

OFF VIGN
3rd Start SW B4
–A1 ON 0V Key “ON ”

OFF VIGN
Brake SW B22
–A1 ON VIGN Key “ON ”

OFF 0V
AT Oil Temperature
Sensor A11
–A12 20
C 4.6V Engine run.

155

C 1.1V
4L Signal B21
–A1 4L 0V Key “ON ”

2H/4H VIGN
Diag SW B12
–A1 ON VIGN Key “ON ”

OFF 0V
Shift Solenoid A (S1) A16
–A1 P VIGN Engine run.

R VIGN

N VIGN

D –1 VIGN

D –2 VIGN

D –3 0V

D –4 0V

7A2-8 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

CHECK ITEM PIN No. VALUE NOTE
Shift Solenoid B (S2) A15 –A1 P 0V Engine run.

R 0V Engine run. (Without the
Reverse range lock out)
N 0V Engine run.
D –1 0V

D –2 VIGN

D –3 VIGN

D –4 0V
Lock-up Solenoid A5
–A1 ON VIGN (ex.) It is “ON ” when the
vehicle speed is more than
65km/h.
OFF 0V
Check Trans Lamp B3
–A1 ON 0V Key “ON ”
(The lamp is “ON ” for 3
second after key “ON ”)

OFF VIGN
AT Oil Temperature Lamp B11
–A1 ON 0V Key “ON ”
(The lamp is “ON ” for 3
second after key “ON ”)

OFF VIGN
Power Lamp B2
–A1 ON 0V Key “ON ”
(The lamp is “ON ” when the
Power switch is “ON ”)

OFF VIGN
3 rd Start Lamp B10
–A1 ON 0V Key “ON ”
(The lamp is “ON ” when the
3rd Start switch is “ON ”)

OFF VIGN
AT Oil Temp Sensor
Resistance A11
–A12 20

C
12k
Key “OFF ”

50

C 1.5k

155

C 293

Pressure Control Solenoid
Resistance A4
–A2 About
4 –7

(20

C)
Key “OFF ”
Speed Sensor Resistance B5 –B14 About
560

– 120
(20

C)
Key “OFF ”
Input Revolution Sensor
Resistance B6
–B16 About
560

– 120
(20

C)
Key “OFF ”
Lock-up Solenoid
Resistance A5
–A1 About
10

– 15
(20

C)
Key “OFF ”
Shift Solenoid A (S1)
Resistance A16
–A1 About
10

– 15
(20
C)
Key “OFF ”
Shift Solenoid B (S2)
Resistance A15
–A1 About
10

– 15
(20

C)
Key “OFF ”

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-11

Comparison of mode
1. The normal drive mode is set at the normal shift
points.
2. The shift points of the power drive mode are shifted
to the higher speed side, compared to the normal
drive mode.
3. The 3rd start mode is a special mode used
exclusively for starting in third gear.
3rd start Mode
1. The 3rd start switch will operate when switched on
after all of the following conditions are present:
a. The gear select position is “D" range only.
b. Vehicle speed is 11 km/h (7 mph) or less.
c. Transmission oil temperature is 120

C (248

F)
or less.
d. Accelerator opening is at 8% or less.
2. Cancel Release
1. Cancellation by driver
a. Turning off the 3rd start mode switch
b. Shifting select position to “3", “2", or “L" (3rd
start mode is not canceled by selecting “N",
“ R", or “P")
c. Ignition key is turned off.
2. Automatic cancellation
a. When vehicle runs at 34 km/h (21mph) o
r
more for 1 second or more
b. When transmission oil temperature reaches 120

C (284

F) or above
NOTE: The mode returns to normal drive mode o
r
power drive mode after the 3rd start mode is canceled.
Backup Mode
If a major system failure occurs which could affect
safety or damage the transmission under normal
vehicle operation, the diagnostic system detects the
fault and overrides the Transmission Control Module
(TCM).
The “CHECK TRANS" light flashes to alert the driver,
and the transmission must be manually shifted as
follows:


Select lever position Gear Ratio Selected
D 4 (Fourth)
Manual 3 4 (Fourth)
Manual 2 3 (Third)
Manual L 3 (Third)
R Reverse
Shifts are firmer to prevent clutch slip and consequent
wear. The fault should be corrected as soon as
possible.

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-13

CAN bus systems in automatic
transmission control (AW30-40LE)
The automatic transmission control system in AW30-
40LE uses high speed CAN bus system .The individual
CAN bus systems are connected via two interfaces and
can exchange information and data. This allows control
modules that are connected to different CAN bus
systems to communicate.
High speed CAN bus
Transmission control modules in the vehicle that require
continuous, rapid communication are connected to the
high speed CAN bus. For example, the automatic
transmission is continuously notified of the current
engine load status. Since the automatic transmission
control module has to react immediately to load status
changes, rapid communication is required between the
engine control module and the automatic transmission
control module. The high speed CAN bus in the AW30-
40LE is designed as a two-wire CAN bus (twisted pair).
The wires are shielded and twisted. The transfer rate is
500 K baud.




RUW37ASF000401
Diagnosis
Electronic Diagnosis
How To Diagnose The Problem
1. To avoid incorrect diagnostics, this book needs to
be followed accurately. Unless stated, do not jump
directly to a section that could contain the
solution. Some important information may be
missed.
2. The sections in CAPITALS and bold are the main
sections that can be found in the contents.
3. The go to “
SECTION"
means to continue to check
going to the “section".
4. The go through “
SECTION"
means to go through
the “section" and then to go back to the place the
go through was written.
5. BASIC ELECTRIC CIRCUITS:
You should understand the basic theory o
f
electricity. This includes the meaning of voltage,
amps, ohms, and what happens in a circuit with an
open or shorted wire. You should also be able to
read and understand wiring diagrams.
Check Trans Indicator
Find CHECK TRANS indicator and verify if it is
A. Flashing: Go to DIAGNOSTIC CHECK.
B. Staying on: Go through CHECK TRANS CHECK
.
C. Is never ON when the ignition key is turned on: Go through CHECK TRANS CHECK
D. Is ON during 3 seconds at ignition but OFF after: Normal operation. No DTC or malfunction.



RTW37ASH000401
On Board Diagnostic Check
This test determines if the transmission or its input or
output connections or sensors are failing.
1. Connect the Tech 2: Go through Tech 2 OBD
CONNECTION .
2. Turn on the ignition but not the engine.
3. Push “F0" on Tech 2 to see the Diagnostic Trouble
Code (DTC):

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-21

Diagnostic Trouble Codes
The purpose of the “Diagnostic Trouble Codes" mode is
to display stored TCM trouble codes.
When “Diagnostic Trouble Codes" is selected an
“ Application Menu" screen appears.
Clear DTC Information
The purpose of the “Clear DTC Information" mode is to
command the clearing of stored TCM trouble codes.
When “Clear DTC Information" is selected, a “Clea
r
DTC Information", warning screen appears. This screen
informs you that by cleaning DTC's, “all stored DTC
information in controller will be erased".
Do you want to clear DTC's (Yes/No).
Press either the Yes or No key when answering.
After clearing codes, confirm system operation by test
driving the vehicle.
Allow the vehicle to shift through all four forward gears
in a manner which attempts to repeat the failure
condition.
NOTE: When the trouble has not been repaired and
the trouble code cannot be erased, check the vehicle
again.
DTC Information
When “DTC Information" is selected, an “Application
Menu" appears with a list of DTC information function
keys addressing DTC specifics and their origins.
Function key selections may vary for particular vehicle
and/or system.
Data Display
The purpose of the “Data Display" mode is to
continuously monitor data parameters.
The current actual values of all important sensors and
signals in the system are display through F1 mode.
When “Data Display" is selected an “Application Menu"
appears. Please select either “Engine" or “Transmission
Data Display".
See “Transmission Data" on next page.
Snapshot
When “Snapshot" is selected an “Application Menu"
appears.
When “Transmission Snapshot" application is selected
from the “Application Menu", a “Snapshot Menu"
appears, displaying several options. “Snapshot" options
may vary from one system to another.
“ Snapshot" allows a recording of all vehicle parameters.
There parameters may then be replayed at a future
point in time.
This action allows you to focus on making the condition
occur, rather than trying to view all of the data in
anticipation of the fault. The snapshot will collect
parameter information around a trigger point that you
select.

When a snapshot is taken. It is recorded onto the
PCMCIA memory card. When the Tech 2 is powered
down. Snapshots are not lost.
Actuator Tests
The purpose of “Actuator Tests" mode is to check fo
r
correct operation of electronic system actuators.
Lamps
You can operate the lamps by pressing the “ON" and
“ OFF" buttons.
Preconditions: none
Solenoid
Solenoid A(S1), Solenoid B(S2)
You can operate the solenoids by pressing the “ON"
and “OFF" buttons.
Preconditions: P –N position, no vehicle speed, no
engine speed
Pressure Control Solenoid (PCS)
You can set desired PCS Current using the “ON" (+20)
and “OFF" (-20) button. The PC Solenoid Data informs
about PCS Current, Pressure and Duty Cycle.
Preconditions: P –N position, no engine speed, no
vehicle speed
NOTE: Freeze Frame
Freeze Frame is an element of the Diagnostic
Management System which stores various vehicle
information at the moment an emission-related fault
is stored in memory and when the Check Transe
Lamp is commanded on. These data can help to
identity the cause of a fault. Refer to Storing An
d
Erasing Freeze Frame Data for more detaile
d
information.

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-27

SERVICE PROGRAMMING SYSTEM (SPS)
The procedure to program the control unit by using the
Service Programming System (SPS) software
contained in TIS2000 is explained below.
NOTE:






Should Tech2 display "SPS Procedure was not
successful", engine will not start, but no DTCs
are present, low battery voltage or poo
r
electrical connections should be the primary
suspects. Perform the SPS procedure again
after rectifying the fault/s.


IMPORTANT:
Perform the following checks before attempting to
program the control unit:







The Tech2 PCMCIA card is programmed with
the latest software release.







The latest release of TIS2000 is loaded on the
PC.







The vehicle battery is fully charged.







The control unit to be programmed is
connected to the vehicle.
1. Preparations of TIS 2000
1.
Connect Tech 2 to P/C.
2.
Check to see if Hardware Key is plugged into Port.
3.
Activate TIS 2000 by P/C.
4.
On the activating screen of TIS2000, choose
"Service Programming System"





5.
On the screen of "Diagnostic Tester and
Processing Program Selection", choose the one
that will comply with the following.

Diagnostic tester in use

New programming by the existing module or new
programming by the replaced/new module.

Fixing position of the control unit.
6.
Upon completion of the selection, push the button
of "Continue".

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-35

DTC P0560 (FLASHING CODE 25) System Voltage Error



RTW37ALF000701
Circuit Description
The Transmission Control Module (TCM) monitors the
system voltage on the ignition feed terminal to the
TCM. A system voltage DTC will set whenever the
voltage is below or above a calibrated value.
Condition for setting the DTC
When the TCM detects following conditions.

Ignition voltage is less than 9V or more than 18V.
 Engine speed is more than 600 rpm.
Action Taken When The DTC Sets

DTC stored.

Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.

The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-37

DTC P0602 (FLASHING CODE 63) Transmission Control Module (TCM)
Programming Error
Circuit Description
The Service Programming System (SPS) updates the
flash calibration files that are stored in a Transmission
Control Module (TCM). The calibration file
custom-tailors a module to a certain vehicle. The
calibration file contains data for things such as spark
curves and fuel control. When troubleshooting a
driveability problem, diagnosis may call fo
r
reprogramming the controller with newer calibration
information to correct a customer concern and Vehicle
Identification Number (VIN).
Condition for setting the DTC
When the TCM is not written VIN No.
Action Taken When The DTC Sets

DTC stored.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids
DTC P0602 is indicated when the TCM does not written
VIN No. A security lock is performed by SPS. And not
replace the TCM when DTC P0602 can repair by SPS.