2004 ISUZU TF SERIES ABS

3C-8 FRONT SUSPENSION


FRONT SUSPENSION
(4




2 Except High Ride Suspension)
CONTENTS

Service Precaution............................................. 3C-8
Shock Absorber ................................................. 3C-9
Shock Absorber and Associated Parts ........... 3C-9
Removal ......................................................... 3C-9
Installation....................................................... 3C-10
Shock Absorber with Coil Spring .................... 3C-12
Stabilizer Bar ..................................................... 3C-15
Stabilizer Bar and Associated Parts ............... 3C-15
Removal ......................................................... 3C-15
Inspection and Repair..................................... 3C-15
Installation....................................................... 3C-16
Knuckle .............................................................. 3C-17
Knuckle and Associated Parts........................ 3C-17
Removal ......................................................... 3C-17
Inspection and Repair..................................... 3C-18
Installation....................................................... 3C-18
Upper Control Arm ............................................. 3C-19
Upper Control Arm and Associated Parts ...... 3C-19
Removal ......................................................... 3C-19
Inspection and Repair..................................... 3C-20
Installation....................................................... 3C-20

Lower Control Arm ............................................. 3C-21
Lower Control Arm and Associated Parts ...... 3C-21
Removal ......................................................... 3C-21
Inspection and Repair..................................... 3C-22
Installation ...................................................... 3C-22
Upper Ball Joint ................................................. 3C-23
Upper Ball Joint and Associated Parts ........... 3C-23
Removal ......................................................... 3C-23
Inspection and Repair..................................... 3C-24
Installation ...................................................... 3C-24
Lower Ball Joint ................................................. 3C-25
Lower Ball Joint and Associated Parts ........... 3C-25
Removal ......................................................... 3C-25
Inspection and Repair..................................... 3C-26
Installation ...................................................... 3C-26
Bump Rubber .................................................... 3C-27
Bump Rubber Joint and Associated Parts...... 3C-27
Removal ......................................................... 3C-27
Inspection and Repair..................................... 3C-27
Installation ...................................................... 3C-27
Special Tools .................................................. 3C-28

Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFE
R
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN
POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM
REPAIRS.



CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, o
r
other corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.

FRONT SUSPENSION 3C-9

Shock Absorber
Shock Absorber and Associated Parts


RTW440LF001201

Legend

(1)
Shock Absorber ASM with coil

(2)
Nut

(3)
Nut

(4)
Nut


(5)
Lower ball joint Nut and cot ter pin

(6)
Nut

(7)
Bolt

(8)
Cam bolt


Removal
1. Raise the vehicle and support it with suitable
safety stands.

2. Remove wheel and tire assembly. Refer to Wheel
Replacement in this section.
3. Remove nut (6).
CAUTION: Be careful not o break the ball joint boot.

3C-10 FRONT SUSPENSION
4. Support lower control arm with a jack.
5. Remove the bolt (7) and nut (4).
6. Remove lower ball joint nut and cotter pin(5), then use remover 5-8840-2017-0 to remove the lowe
r
ball joint from the knuckle.

P1010003
7. Apply the setting marks to the front and rear cam
bolt and cross member, then loosen nut, and cam
bolt.
8. Remove the nut (2).
9. Remove to Shock Absorber ASM.


Installation
1. Install shock absorber.

RTW340MF000801

3C-12 FRONT SUSPENSION
Shock Absorber with Coil Spring

RTW340LF002101

Legend

1. Nut
2. Washer

3. Bushing ; Rubber

4. Mounting Bracket

5. Coil Spring


6. Bushing ; Rubber

7. Washer

8. Shock Absorber ASM

FRONT SUSPENSION 3C-13
Disassembly





1. Install the support fixture (5-8840-0595-0) to the base (5-
8840-003-0).
2. Install the upper adapter (5-8840-0597-0) and the lower
adapter (5-8840-0596-0) to the base and support fixture
assembly.
3. Install the shock absorber assembly to the support fixture.
4. Remove the nut with spring in place.
CAUTION:
Take care not to apply excessive force to the nut during
removal.


CAUTION :
The shock absorbers have been charged with gas at the
factory. Exposure to high temperatures or an open flame
can result in a dangerous explosion.
Keep the shock absorbers away from high temperatures
and open flames.



INSPECTION AND REPAIR
Make all necessary adjustments, repairs, and part replacements if wear, damage, or other problems are discovered
during inspections.




Visual Check
Inspect the following parts for wear, damage or other abnormal
conditions.


Shock absorber


Rubber bushing


Coil spring

3C-22 FRONT SUSPENSION
4. Support lower control arm with a jack.
5. Remove the nut (10).
6. Remove the nut (8).
7. Remove the shock absorber lower end from the
lower control arm.
8. Remove the lower ball joint from the lower control arm.
9. Remove nut (4) and cam plate.
10. Remove cam bolt.
11. Remove lower control arm.
12. Remove bushing.
Inspection and Repair
Make necessary correction or parts replacement if
wear, damage, corrosion or any other abnormal
condition are found through inspection.
Check the following parts:


Lower control arm


Bushing
Installation
1. Install rear bushing by using installer 5-8840-
0257-0 and 5-8840-2327-0.


P1010063
2. Install lower control arm.
3. Install cam bolt.
4. Install lower ball joint and tighten it to the specified
torque (9).
Torque: 127 N






m (12.9kg






m/94 lb ft)
5. Install shock absorber and tighten it to the specified torque (5).

NOTE: Apply oil to the thread.
NOTE: Tighten the nut (4) with the parts in the position
shown in the illustration below.
Torque: 137 N






m (14.0kg






m/101 lb ft)




RTW340SH001301-X
6. Install stabilizer link and tighten it to the specified
torque (10).
Torque: 50 N






m (5.1kg






m/37 lb ft)
7. Install nut (4) and cam plate and tighten lower link nut finger-tight.
NOTE: Apply oil to the thread.
NOTE: Tighten the nut (4) with the parts in the position
shown in the illustration below.
Buffer clearance: 25.9 mm (1.02 in)
Torque: 186 N






m (19.0kg






m/137 lb ft)





RTW340SH001301-X
8. Install nut (8) and cotter pin then tighten the nut to
the specified torque, with just enough additional
torque to align cotter pin holes. Install new cotte
r

3C-30 FRONT SUSPENSION


FRONT SUSPENSION
(4





2 High Ride Suspension, 4





4)
CONTENTS

Service Precaution............................................. 3C - 29
Shock Absorber ................................................. 3C - 30
Shock Absorber and Associated Parts ........... 3C - 30
Removal ......................................................... 3C - 30
Inspection and Repair..................................... 3C - 30
Installation....................................................... 3C - 30
Stabilizer Bar ..................................................... 3C - 31
Stabilizer Bar and Associated Parts ............... 3C - 31
Removal ......................................................... 3C - 31
Inspection and Repair..................................... 3C - 31
Installation....................................................... 3C - 32
Torsion Bar ........................................................ 3C - 33
Torsion Bar and Associated Parts .................. 3C - 33
Removal ......................................................... 3C - 33
Inspection and Repair..................................... 3C - 34
Installation....................................................... 3C - 34
Knuckle .............................................................. 3C - 36
Knuckle and Associated Parts........................ 3C - 36
Removal ......................................................... 3C - 36
Inspection and Repair..................................... 3C - 38
Installation....................................................... 3C - 38
Upper Control Arm ............................................. 3C - 39
Upper Control Arm and Associated Parts ...... 3C - 39
Removal ......................................................... 3C - 39

Inspection and Repair..................................... 3C - 40
Installation ...................................................... 3C - 41
Lower Control Arm ............................................. 3C - 43
Lower Control Arm and Associated Parts ...... 3C - 43
Removal ......................................................... 3C - 44
Inspection and Repair..................................... 3C - 45
Installation ...................................................... 3C - 45
Upper Ball Joint ................................................. 3C - 47
Upper Ball Joint and Associated Parts ........... 3C - 47
Removal ......................................................... 3C - 47
Inspection and Repair..................................... 3C - 48
Installation ...................................................... 3C - 48
Lower Ball Joint ................................................. 3C - 49
Lower Ball Joint and Associated Parts ........... 3C - 49
Removal ......................................................... 3C - 49
Inspection and Repair..................................... 3C - 50
Installation ...................................................... 3C - 50
Bump Rubber .................................................... 3C - 51
Bump Rubber and Associated Parts .............. 3C - 51
Removal ......................................................... 3C - 51
Inspection and Repair..................................... 3C - 51
Installation ...................................................... 3C - 51
Special Tools .................................................... 3C - 52



Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFE
R
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN
POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM
REPAIRS.



CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, o
r
other corrosion inhibitors) on threaded fasteners o
r
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.

FRONT SUSPENSION 3C-31

Shock Absorber
Shock Absorber and Associated Parts
RTW340MF000901
Legend

(1)
Nut

(2)
Rubber Bushing and Washer

(3) Bolt and Nut

(4)
Shock Absorber
(5) Rubber Bushing and Washer


Removal
1. Raise the vehicle and support it with suitable
safety stands.
2. Remove wheel and tire assembly. Refer to Wheel
Replacement in this section.
3. Remove bolt and nut.
4. Remove nut.
5. Remove rubber bushing and washer.
6. Remove shock absorber.
7. Remove rubber bushing and washer.
Inspection and Repair
Make necessary correction or parts replacement if
wear, damage, corrosion or any other abnormal
condition are found through inspection.
Check the following parts :


Shock absorber


Rubber bushing
Installation
1. Install rubber bushing and washer.
2. Install shock absorber.
3. Install rubber bushing and washer.
4. Install nut (1), then tighten it to the specified
torque.
Torque: 20 N




m (2.0kg




m/14 lb ft)
5. Install bolt and nut (3), then tighten to the specified
torque.
Torque: 93 N




m (9.5kg




m/69 lb ft)