2004 ISUZU TF SERIES ABS

8A-192 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION









DOME LIGHT
Removal
1. Remove the dome light lens 1 free.
2. Remove two dome light fixing screws.
3. Remove the wiring connector.
4. Remove the dome light.
5. Pull the bulb
2 to remove it.







Installation
Follow the removal procedure in the reverse order to install the
dome light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulb
Be absolutely sure that the dome light bulb is correctly
installed.
This will prevent a poor contact and an open circuit.

ELECTRICAL-BODY AND CHASSIS 8A-193

DOOR SWITCH
Removal
1. Disconnect the battery ground cable.
2. Loosen the screw

1.
3. Remove the door switch.
4. Disconnect the door switch connector
3.





Installation
Follow the removal procedure in the reverse order to install the
spot light.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the door switch connector is securely
connected.
This will prevent a poor contact and an open circuit.


SPOT LIGHT (MAP Light)
Removal
1. Grasp the spot light housing
1 with both hands.
Pull the housing straight down.
This will release the clip.
2. Disconnect the connector

2.
3. Turn socket
3 counterclockwise to remove it.

8A-194 ELECTRICAL-BODY AND CHASSIS



Installation
Follow the removal procedure in the reverse order to install the
spot light.
Pay close attention to the important points mentioned in the
following paragraphs.


Connector
Be absolutely sure that the spot light connector is securely
connected.
This will prevent a poor contact and an open circuit.



Bulb
Be absolutely sure that the spot light bulb is correctly installed.
This will prevent a poor contact and an open circuit.




RTW48ASH000801
WARNING BUZZER (ALARMER
CONTROL UNIT)
Removal
1. Disconnect the battery ground cable.
2. Remove the glove box

Remove the screw.
3. Remove the Alarmer C/U assembly

Remove the screw.





Installation
Follow the removal procedure in the reverse order to install the
warning buzzer.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the warning buzzer connector is
securely connected.
This will prevent a poor contact and an open circuit.

ELECTRICAL-BODY AND CHASSIS 8A-207
REMOVAL AND INSTALLATION


WIPER AND WASHER SWITCH
Removal
Refer to the removal steps of the LIGHTING SWITCH
(COMBINATION SWITCH) in “ LIGHTING “ of this section.





Installation
Follow the removal procedure in the reverse order to install the
wiper and washer switch.
This illustration is based on RHD model
Pay close attention to the important points mentioned in the
following paragraphs.

Connector
Be absolutely sure that the wiper and washer switch connector
is securely connected.
This will prevent a poor contact and an open circuit.

8A-212 ELECTRICAL-BODY AND CHASSIS
Windshield Washer Spray
Be sure that the engine hood is completely closed before
checking the windshield washer spray adjustment.
Windshield Washer Spray Position: Refer to the illustration.

RTW38DSF000201



Connector
Be absolutely sure that the wiper motor connector is securely
connected.
This will prevent a poor contact and an open circuit.


Note:
Windshield wiper arm and blade assembly configurations
are different for the right-hand and left-hand side of the
vehicle.
Be careful not to confuse the right-hand and left-hand side
assemblies.



This illustration is based on RHD model
WASHER TANK MOTOR
Removal
1. Remove the head light.

Refer to the head light in this manual.
2. Remove the inner riner.
3. Pull out the clip washer filler.
4. Remove the washer tank nuts.

ELECTRICAL-BODY AND CHASSIS 8A-213


4. Disconnect the connector
1.
5. Disconnect the water hose

2.


6. Pull out the washer tank motor
3.




Installation
Follow the removal procedure in the reverse order to install the
washer tank motor.
Pay close attention to the important points mentioned in the
following paragraphs.


Connector
Be absolutely sure that the washer tank motor connector is
securely connected.
This will prevent a poor contact and an open circuit.

8A-262 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION

This illustration is based on RHD model
METER ASSEMBLY
Removal
1. Meter Cluster Assembly

Refer to the removal steps of “INSTRUMENT PANEL” in
Section 10 “CAB”
2. Meter Assembly

Remove three screws of the meter assembly.

Disconnect the meter connectors.






Installation
Follow the removal procedure in the reverse order to install the
meter.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the meter connectors are securely
connected.
This will prevent a poor contact and an open circuit.



Wire Harness
Do not pinch the wire harness between the cluster and the
meter hood during the meter assembly installation procedure.
Wire damage will result.

8A-264 ELECTRICAL-BODY AND CHASSIS
Installation

Rubber Seal
Be absolutely sure that the fuel tank unit rubber seal is
correctly seated.



Connector
Be absolutely sure that the fuel tank unit connector is securely
connected.
This will prevent a poor contact and an open circuit.



VEHICLE SPEED SENSOR (INSTALLED
ON THE TRANSMISSION)
Removal
1. Disconnect the connector.
2. Remove the vehicle speed sensor body by rotating it.







Installation
To Install, follow the removal steps in the reverse order, noting
the following point.
Tighten the vehicle speed sensor to the specified torque.
Vehicle Speed Sensor Tightening Torque Nm (kgfm/lb.ft)
25  4.9 (2.5  0.5/18  3.6)