2004 ISUZU TF SERIES ABS

BRAKE CONTROL SYSTEM 5A-35

Basic Diagnostic Flow Chart

RTW45AMF000101

Step Action Value(s) Yes No
1 1. Ignition “ON,”engine “OFF.”
2. Observe the ABS warning lamp.
Note: If a starter switch is turned ON, ABS warning
lamp will turn on and a ABS warning lamp will be
turned off after 3 seconds.
Is the ABS warning lamp “ON”?
- Go to Step 2 Go to “No
ABS warning
lamp”
2 1. Ignition “OFF.”
2. Install Tech2.
3. Ignition “ON.”
4. Attempt to display ABS data with the Tech 2.
Does the Tech 2 display ABS data?
- Go to Step 5 Go to Step 3
3 1. Ignition “OFF,” disconnect the EHCU.
2. Check the DLC (Data Link Connector) circuit for an
open, short to ground, or short to voltage.
Also, check the DLC ignition feed circuit for an
open or short to ground and the DLC ground circuit
for an open.
3. If a problem is found, repair as necessary.
Was a problem found?
- Go to Step 2 Go to Step 4

BRAKE CONTROL SYSTEM 5A-37

Basic Inspection Procedure
1. Basic Inspection of Service Brake
Step Action
Value(s) Yes No
1 Is the fluid level normal?
- Go to Step 2 Replenish with
fluid
Go to Step 2
2 Does fluid leak?
- Repair
Go to Step 3 Go to Step 3
3 Is the booster function normal?
- Go to Step 4 Repair
Go to Step 4
4 Is the pad and rotor normal?
- Go to Step 5 Repair
Go to Step 5
5 Reconnect all components. Ensure all component
are properly mounted.
Was this step finished? - Finished Go to Step 5

2. Ground Inspection
Step Action
Value(s) Yes No
1 Does ABS related ground points normally?
- Go to Step 2 Repair
Go to Step 2
2 Reconnect all components. Ensure all component
are properly mounted.
Was this step finished? - Finished Go to Step 2

BRAKE CONTROL SYSTEM 5A-39

Symptom Diagnosis
The symptoms that cannot be indicated by warning
lamp can be divided in the following five categories:
1. ABS works frequently but vehicle does not
decelerate.
2. Uneven braking occurs while ABS works.
3. The wheels are locked.

4. Brake pedal feel is abnormal.
5. Braking sound (from EHCU) is heard while not
braking.
6. No ABS warning lamp
These are all attributable to problems which cannot be
detected by EHCU self-diagnosis. Use the customer
complaint and a test to determine which symptom is
present.
ABS Works Frequently But Vehicle Does Not Decelerate

Step Action
Value(s) Yes No
1 Is braking force distribution normal between front
and rear of vehicle?
- Go to Step 2 Repair brake
parts.
Go to Step 7
2 Are axle parts installed normally?
- Go to Step 3 Repair axle
parts.
Go to Step 7
3 Is there play in each or any wheel speed sensor?
- Repair wheel
speed sensor.
Go to Step 7 Go to Step 4
4 Is there damage, or powered iron sticking to each or
any wheel speed sensor/sensor rotor?
- Replace
wheel speed
sensor or
sensor rotor.
Go to Step 8 Go to Step 5
5 Is the each wheel speed sensor output normal?
- Go to Step 6 Replace
wheel speed
sensor or
repair
harness.
Go to Step 7
6 Is the 4WD control system function normal?
- 2-4WD Repair
or Go to Step
7 Repair or
replace 2-
4WD control
System.
Go to Step 7
7 Reconnect all components, ensure all components
are properly mounted.
Was this step finished?
- Repeat the
“Basic
diagnostic
flow chart” Go to Step 7

5A-40 BRAKE CONTROL SYSTEM

Uneven Braking Occurs While ABS Works

Step Action
Value(s) Yes No
1 Is there play in each or any sensor?
- Repair.
Go to Step 5 Go to Step 2
2 Damage or powdered iron sticking to each or any
sensor/sensor rotor?
- Repair.
Go to Step 5 Go to Step 3
3 Is the each sensor output normal?
- Go to Step 4 Replace
sensor or
repair
harness.
Go to Step 5
4 Is brake pipe connecting order correct?
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification; 2WD Model or 4WD Model) - Replace
EHCU.
Go to Step 5 Reconnect
brake pipe
correctly.
Go to Step 5
5 Reconnect all components, ensure all components
are properly mounted.
Was this step finished?
- Repeat the
“Basic
diagnostic
flow chart” Go to Step 5

The Wheels Are Locked

Step Action Value(s) Yes No
1 Is ABS working?
- Go to Step 2 Go to Step 4
2 Is vehicle speed under 5 km/h?
- Go to Step 3 Normal.
3 Is the each sensor output normal?
- Go to Step 4 Replace
sensor or
repair
harness.
Go to Step 6
4 Is 2-4WD system function normal?
- Go to Step 5 Replace 2-
4WD controll
unit or repair
harness.
Go to Step 6
5 Is EHCU grounded properly?
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification; 2WD Model or 4WD Model) - Replace
EHCU.
Go to Step 6 Repair.
Go to Step 6
6 Reconnect all components, ensure all components
are properly mounted.
Was this step finished?
- Repeat the
“Basic
diagnostic
flow chart” Go to Step 6

5A-42 BRAKE CONTROL SYSTEM

Braking Sound (From EHCU) Is Heard While Not Braking

Step Action Value(s) Yes No
1 Is this the first vehicle start after engine start?
- It is self
checking
sound
Normal. Go to Step 2
2 Is vehicle speed under 10 km/h?
- It is self
checking
sound
Normal. Go to Step 3
3 Check for the following condition:
 At the time of shift down or clutch operation.
 At the time of low road friction drive (ice or snow
road) or rough road drive.
 At the time of high-speed turn.
 At the time of passing curb.
 At the time of operating electrical equipment
switches.
 At the time of racing the engine.
Did it occur under any one condition above?
- ABS may
sometimes be
actuated even
when brake
pedal is not
applied. Go to Step 4
4 Is there play in each or any sensor/wheel speed
sensor rotor?
- Repair.
Go to Step 7 Go to Step 5
5 Damage or powdered iron sticking to each or any
sensor/wheel speed sensor rotor?
- Repair.
Go to Step 7 Go to Step 6
6 Is each sensor normal?
Note : Check the EHCU type for specification, the
EHCU is replaced.
(Specification; 2WD or 4WD Model)

- Check
harness/
connector for
suspected
disconnection
If no
disconnection
is found,
replace EHCU
Go to Step 7 Repair.
Go to Step 7
7 Reconnect all components, ensure all components
are properly mounted.
Was this step finished?
- Repeat the
“Basic
diagnostic
flow chart” Go to Step 7

BRAKE CONTROL SYSTEM 5A-43

No ABS Warning Lamp

Step Action
Value(s) Yes No
1 Check the meter fuse for the instrument cluster
ignition feed circuit.
Is the fuse OK? - Go to Step 3 Go to Step 2
2 Replace the fuse.
Is the action complete? - Verify repair
Go to Step 3 -
3 1. Ignition “OFF,” disconnect the EHCU.
2. Ignition “ON,”engine “OFF.”
3. Observe the ABS warning lamp.
Is the ABS warning lamp “ON”?
- Go to Step 5 Go to Step 4
4 Repair or replace the meter circuit or meter.
Is the action complete? - Verify repair -
5 1. Check the EHCU circuit for an open, short to
ground, or short to voltage. Also, check the EHCU
ignition feed circuit for an open or short to ground
and the EHCU ground circuit for an open.
2. If a problem is found, repair as necessary.
Was a problem found?
- Verify repair Go to Step 6
6 1. Ignition “OFF,” reconnect the EHCU.
2. Ignition “ON,”engine “OFF.”
3. Observe the ABS warning lamp.
Is the ABS warning lamp “ON”?
- Verify repair Go to Step 7
7 Replace EHCU.
Note : Check the EHCU type for specification, the
EHCU is replaced.
(Specification; 2WD or 4WD Model)
Is the action complete? - Verify repair -

BRAKE CONTROL SYSTEM 5A-77

DTC C0267 (Flash Code 67) ABS Motor Shorted to Ground
DTC C0268 (Flash Code 68) ABS Motor Shorted to Battery



RTW45AMF000201

Step Action
Value(s) Yes No
1 Was the “Basic Diagnostic Flow Chart” performed?
- Go to Step 2 Go to Basic
Diagnostic
Flow Chart
2 1. Ignition “OFF”.
2. Check the EHCU circuit for an open, short to
ground, or short to voltage. Also, check the EHCU
ignition feed circuit for an open or short to ground
and the EHCU ground circuit for an open or short to
voltage.
3. If a problem is found, repair as necessary.
Was a problem found?
- Verify repair Go to Step 3
3 1. Ignition “ON,” engine “OFF.”
2. Select “Display DTCs” with the Tech 2.
Note: Perform the various tests (actuator test, test
run, brake test, etc.) then observe the DTC with a
Tech2.
Are any DTCs stored? - Go to Step 4 Verify repair

5A-80 BRAKE CONTROL SYSTEM

DTC C0274 (Flash Code 74) ABS Operation Long Time


RTW45AMF000201

Step Action
Value(s) Yes No
1 Was the “Basic Diagnostic Flow Chart” performed?
- Go to Step 2 Go to Basic
Diagnostic
Flow Chart
2 Was the “Basic Inspection Procedure” performed?
- Go to Step 3 Go to Basic
Inspection
Procedure
3 1. Check for a poor connection at the wheel speed
sensor harness connector.
2. Check installation condition for wheel speed
sensor.
3. If a problem is found, repair as necessary.
Was a problem found? - Verify repair Go to Step 4
4 1. Check condition for sensor rotor.
2. If a problem is found, repair as necessary.
Was a problem found? - Verify repair Go to Step 5
5 1. Ignition “OFF,” disconnect the EHCU and wheel
speed sensor.
2. Check the circuit between EHCU and wheel speed
sensor.(short ground, or short to voltage.)
3. If a problem is found, repair as necessary.
Was a problem found? - Verify repair Go to Step 6