2004 DACIA SOLENZA warning

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 28
Diag nostic
No
Is the anti starting bushing correctly fixed on
the steering column and is it correctly connected
?Position the bushing and fix its
connection.
Check the continuity and the isolation related
to the mass and the +12 V wiring.
Pin2 mass
Pin3 supply +IC
Pin4 pin A2 of the
E.C.U. decoder.
Is the wiring in good condition?
Fix the electric wiring.
Disconnect the E.C.U. decoder and check the
presence of +12 V at pin A2 of the wiring.
Is there any tension?Replace the anti starting bushing.
Connect t he E.C.U. decoder. Perform the
impulse detection t est with t he t ester CLIP
branched to the pin A2 of the E.C.U. decoder.
S et the contact on and check t he presence of
an impulse. Is there any impulse?
Replace the E .C.U. decoder.
Replace the key.
No
No
No
No
Yes
Yes
Yes
No
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 29
Diag nostic
ALP3. THE ANTI STARTING INDICATOR REMAINS PERMANENTLY LIGHTED
( even when the contact is taken off) OR IT REMAINS PERMANENTLY SWITCHED
OFF
RECOMMENDATION Check if the “Procedure E.C.U. decoder replacement” was correctly performed
Check the fuse F03 condition from the cockpit
fuse box.
Is the fuse good?
Is there the failure “DOORS BLOCKING
CONTACT”.
Check the continuity and the isolation related
to the mass, between the pin A 5 of the E.C.U.
decoder and the dashboard.(pin 6 from black
connector)
Is the wiring good?
Replace the fuse.
Analyse this failure and replace.
Fix the wiring.
Perform the following tests in order to find the
damaged element:
- if the anti starting indicator is permanently
lighted, disconnect the connector of the E.C.U.
decoder a nd check if t he indicator switches
off;
- if the anti starting system is turned off, connect
the pin A5 of t he wiring connector from the
E.C.U. decoder to an electric mass and check
if the indicator turns on.
Are the answers affirmatives?
Replace the instrument panel.
Replace the E .C.U. decoder.
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system.
Remove by means of the CLIP tester the possible m emorised
failures.
No
No
No
Yes
Y e s
No
Yes
Yes
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 30
Diag nostic
ALP4. CONTACT ON THE ANTI STARTING INDICATOR BLINKS QUICKLY
(engine is not starting)
RECOMMENDATION-
S et the contact on.
Connect the CLIP tester.
Is there any communication between the
tester and E .C.U. decoder ?
Is the state 19D, ACTIVE?
Check the continuity and the isolation related
to the mass and to the + 12V of the wiring
be t we en A6 de c ode r pi n a nd i nj e c t ion
computer pin 58.
Is the wiring good?
S ee ALP1.
Check the correct memorisation of
the anti starting code by the
E.C.U. decoder ; if not, replace
the decoder.
Fix the electric wiring.
Perform the impulse detection test by means
of the CLIP tester connected to the E.C.U.
decoder A6 pin.
Set th e conta c t on a nd c he ck i mpulse s
presence.
Are there any impulses?
Replace the injection computer.
Replace E.C.U. decoder or see t he “ Kit
replacement procedure “.
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system.
Remove by means of the CLIP tester the possible m emorised
failures.
No
Yes
No
Yes
Yes
No
Yes
No
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 31
Diag nostic
ALP5. THE VEHICLE IS NOT STARTING
RECOMMENDATION-
Is there the failure “SIGNAL MISSING ON
THE CODED LINE E.C.U. DECODER –
COMPUTER INJECTION?”
There is a problem at the shock sensor.
There is an engine problem.No
Yes
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system.
Remove by means of the CLIP tester the possible m emorised
failures.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 32
Diag nostic
ALP6. BLOCKING/UNLOCKING DOORS NOT OPERATING
RECOMMENDATION Check with the CLIP tester the absence of the failures.
If there are memorised failures, these must be removed.
Are the doors blocking mechanisms correctly
operating ?Repair the damaged mechanisms.No
Check the continuity and the isolation related to the
mass of the wiring between :
E.C.U . decoder pin B8 actuators
Pin B9 doors
Is the wiring in good condition?
Fix the wiring.No
Check the continuity and the isolation
related to the mass of the wiring between
E.C.U . pin B2 1 switch
decoder Pin B5 5 blocking doors
Is the wiring in good condition?
Repair.
Di sconnect the E.C.U. decoder, then supply
the wiring c onnector with +12 V at pin B9
and the mass at the pi n B8, than versa (+ 12
V at pin B8 and t he mass at pi n B9).
Ar e the actuators bl ocking/unlocking the
doors?
Damaged actuators.
Replace them.
Replace the E.C.U. decoder, t hen perform the “E.C.U. decoder
replacement procedure”. No
Yes
Yes
No
YesYes
AFTER REPAIRING Perform a conformity
checking.
Check the operation of the anti starting system.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 33
Diag nostic
ALP7. UNLOCKING DOORS NOT OPERATING BY RF REMOTE CONTROL
RECOMMENDATION Check the absence of failures with the CLIP tester.
If there are memorised failures, these must be repaired.
Are the states 11G and 11D be c om ing
A CTIVE when t he RF remote c ontrol is
activated?S ee the treatment of the states 11G
and 11D cf. chapter “Diagnostic”.No
Check the fuse F03 condition from the cockpit
fuse box.
Is it good?
Replace the fuse.No
Ye s
Yes
See the treatment of the failure
“Doors blocking contact” and the state 14 G cf. chapter
“Diagnostic”.
See ALP6.
Yes
No
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
Activate the doors’ locking switch from the
dashboard.
Are the doors blocking/ unlocking ?
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 34
Diag nostic
ALP 8. TURNING LIGHTS DO NOT SWITCH ON AT THE BLOCKING /
UNLOCKING OF THE DOORS
RECOMMENDATION Check the absence of the failures with the CLIP tester. If there are failures, fix them first.
Check if the synchronisation of the RF remote control and the E.C.U. decoder has been
performed.
Are the turning lights functioning normally at the activation of the signalling switch ?
Check the continuity and the isolation
related to t he mass and the +12 V of the
electric layout:
E.C.U. decoder FLASH relay
Pin B3 pole 2
Is it correct?
Repair the signalling system.
Check t he fuse F03 and F04.
Fix the electric layout.
Check the fuse F02 condition from the cockpit
fuse box.
Is it good?Replace the fuse.
Di sconnect the FLASH relay. Supply with
+12, the pole 4 of the relay. Are the left turning
lights turning on? Supply with +12 V the pole
5 of the signal relay. Are the right/left turning
lights turning on?
Repair the electric layout from
poles 4 and 5 of the FLASH relay.
Replace the FLASH relay.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
No
No
No
Yes
Yes
Yes
Yes No
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 35
Diag nostic
No
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
A LP9. THE CEILING LAMP DOES NOT SWITCH ON AT THE BLOCKING /
UNLOCKING OF THE DOORS OR IT REMAINS PERMANENTLY TURNED ON
RECOMMENDATION Check the absence of failures with the CLIP tester. If there are memorised failures, fix them first.
Check if t he doors are locked? The ceiling lamp was in
the position “permanently
lighting”? Normal
operation.Yes Yes
Unlock the doors with the RF remote control.
The ceiling is in the position “ceiling delayed
lighting ”.
Has the ceiling lamp turned on?
Check the isolation of the wiring related
to the mass on the line pinA1.
decoder pin 3 c eiling lamp.
After 15 seconds, the ceiling lamp will
turn off.
Normal operation.
Wa s the E.C.U. decoder confi gured “With
ceiling delayed lamp”?Configure the E.C.U. decoder with
the CLIP tester.
Check the continuity on the line
E.C.U. decoder pin A1 pin 3 ceiling
lamp.
Is the line good?Repair .
Check the ceiling lamp bulb.
No
No
No
Yes
Yes Yes
No
vnx.su