2004 DACIA SOLENZA warning

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 12
Procedures
A. E.C.U. DECODER REPLACEMENT PROCEDURE AND
ANTI STARTING CODE MEMORISING
The new E.C.U. decoder is always not coded. After its mounting on the vehicle it is necessary
that this one is memorising the anti starting code in order to be operational.
REMARK:
If only the E.C.U. decoder i s replaced, there i s no need of an i ntervention to t he
E.C.U. injection (injection computer), which will keep the old anti starting code.
AT T E N T I ON!
After the E.C.U. de coder memorised the anti starting c ode, this code cannot be erased
or replaced with another one. In order t o perform this procedure, one of the keys of t he ve hicle and the CLIP tester are
needed.
Proceed as follows:
1. Connect the CLIP tester to the diagnostic socket and to the battery (or the lighter socket)
of the vehicle. 2. Read the configuration of the old E.C.U. decoder in the following way, before dismounting
it from the vehicle:
- select the type “B41”
- enter the menu “ COMPUTER TEST” then select “ ANTI STARTING”
- access “COMMAND MODE” then “CONFIGURATIONS READING”
- note the configurations found : petrol, programming with 1 or 2 keys, ceiling delayed
light, the type of the doors’ blocking switch (CPE), etc.;
3. Return to the menu “COMPUTER TEST”
4. Remove the old E .C.U. decoder and replace it with a new one, the contact being off.
5. Enter the menu “ANTI STARTING”, then select “ STATE LIST”. If the E.C.U. decoder is
new, you must find the following states:
18G FIRST CYCLE MEMORISING………………….......………… PASSIVE
19G NOT PERFORMED KEY PROGRAMMING ………..……….. ACTIVE
19D UNBLOCKED KEY PROGRAMMING ……………….………ACTIVE
OBSERVAT ION:
If the states 19G and 19D are not “ACTIVE” this means the E.C.U. decoder has
b een already used, so it isn’t new and cannot memorise another anti starting code.
6. Access t he menu “COMMAND MODE” and then “CONFIGURATION”, where you
will c onfigure t he new E .C.U. decoder in the same way as the old one : petrol, 1 ke y, ceiling
delayed light, impulsion doors blocking switch, etc. selecting one by one these configurations,
which you’ll validate with “CLICK” on the blue button on right top of the screen.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 13
Procedures
1. Return to “COMPUTER TEST”
2. Set the contact on for 2 seconds in “ M” position, without start ing the engine. The anti
starting indicator will begin to blink rapidly.
3. Access the menu “ STATE LIST”, where the following states must exist:
9D RECEIVED KEY CODE ………………………………......…… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING …………….…… PASSIVE
10. Take the c ontact off. In the menu “COMMAND MODE” select “ACTUATORS”, then
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear, followed
by “ FINISHED COMMAND”. 11 . The anti starting indicator will blink rarely.
12. Return to the “STATE LIST”, which now, must be like that: 18G FIRST CYCLE MEMORISING…………………………….....…ACTIVE
19G NOT PERFORMED KEY PROGRAMMING…………….……..PASSIVE
19D UNBLOCKED KEY PROGRAMMING …………………..…… PASSIVE
13. Set the contact i n “M” position for 2-3 seconds in order t o send the code t o the E.C.U.
injection. The anti starting indicator must light for 3 seconds, then turn off.
14. Take off the contact. After 10 seconds, the anti starting indicator will blink rarely.
15. Check the engine starting with both keys, and then take the contact off.
16. Check in the menu “ STATE LIST ” if the state 10G “ANTI STARTING” is “ ACTIVE”.
Perform the synchronisation of the TRF remote control with the decoder (with 1or 2 keys).
OBSERVAT ION:
With the CLIP tester, a starting interdiction may be simulated, proceeding as follows:
- take the contact off; wait for 10 seconds, then the anti starting indicator will blink;
- in the menu, “COMMAND MODE” access “ ACTUATORS” then validate “ FORCED
PROTECTION MODE” launching the command from the blue button situated on the ri ght
topside of the screen. “COMMAND IN PROGRESS” will be displayed and then “FINISHED
COMMAND”; - in t he m enu “ STATE LIST” search for the state 10G ”ANTI START ING”, which
must be “ ACTIVE”; - set the contact on “M” position; the anti starting indicator will blink rapidly, and the
engine starting is impossible;
- remove the key from the contact and check then the engine starting with both keys, so
the procedure is finished.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 14
Procedures
RE M ARK:
For the RF remote control synchronisation, after the replacement of an E.C.U. decoder,
the sync hron is ation proced ure must be per formed taking i nto account the foll owing
situations : - fo r one RF remote control, perform the “ SIMPLE SYNCHRONISED
PROCED URE ”;
- for the second RF remote co ntrol per form the “SPE CI FI C SYNCHRONI SED
PROCED URE ”.
B. KIT REPLACEMENT PROCEDURE
(E.C.U. decoder plus 2 key he ads)
In case of one kit replacement perform the following steps:
- memorising the anti starting code by the E.C.U. decoder;
- memorising of the new anti starting code by the injection computer; it is necessary the
repairing code (found out based on the old ke y heads code) and t he CLIP tester.
Perform the actions in the following sequence:
1. Mount the metal insertions of the old keys to the new key heads.
2. Inform by phone at ”Client Voice” (phone no 0248 500 000), the vehicle chassis series and
the key heads code, written on the vehicle invoice, in order to get the repairing code.
3. Connect the CLIP tester t o the diagnostic socket and to the battery (or to the lighter
s ocket) of the vehicle. Read the configuration of the old E.C.U. decoder before dismounting it
off the vehicle, as follows:
- select vehicle type “B41”;
- enter the menu “ COMPUTER TEST” then select “ ANTI STARTING”;
- access “COMMAND MODE” then “READ CONFIGURATIONS”;
- note the configuration s : petrol/diesel, programming with 1 or 2 keys, ceiling delayed light,
the type of the doors’ blocking switch (CPE), etc.
4. Return to the menu “ANTI START ING”.
5. Dismount the old E.C.U. decoder and replace it with a new one, the contact being off.
6. Check the configuration of the new E.C.U. decoder selecting “ STAT E LIST”; here you
must find the following states: 18G FIRST KEY MEMORISING……………………………........… PASSIVE
19G NOT PERFORMED KEY PROGRAMMING ………………..... ACTIVE
19D UNBLOCKED KEY PROGRAMMING ……………………..... ACTIVE
REMARK:
If the state 19G and 19D are not “ACTIVE” this means the E.C.U. decoder isn’t a
ne w one and cannot memorise another anti starting code.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 15
Procedures
7. Set the contact i n “M” position with one of the ke ys (without start ing the engine), for
about 2 seconds and then check the following states, which must be:
9D RECEIVED KEY CODE ……………………………….....…..... ACTIVE
19G NOT PERFORMED KEY PROGRAMMING ………….........… ACTIVE
8. Set the contact with the second key (without starting t he engine) for about 2 seconds.
Check then the following states:
-case (a)- the second key belongs to the vehicle;
9D RECEIVED KEY CODE ……………………………………..… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING …………….....… PASSIVE
- case (b)- t he second key doe s not belong to t he vehicle or the first ke y was used once
again;
9D RECEIVED KEY CODE ……………………………………..… PASSIVE
19G NOT PERFORMED KEY PROGRAMMING ………….....…… ACTIVE
9. The anti starting indicator blinks rapidly.
10. Take off the contact. In the menu “ COMMAND MODE” select “ACTUATORS” and
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear,
followed by “ FINISHED COMMAND”. 11 . The anti starting indicator will blink rarely.
12. Return to the “STATE L IST”, which now must be as follows: 18G FIRST KEY MEMORISING…………………………….........… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………...……PASSIVE
19D UNBLOCKED KEY PROGRAMMING ………………...…...…PASSIVE
13. In the menu “COMMAND MODE” select “ ACTUATORS”. Select the command “
FORCED PROTECTION MODE” launching the command from the blue button situated on
the ri ght topside of the screen. The display will show “COMMAND IN PROGRESS” and
then “FINISHED COMMAND”.
Return to the “STATE LIST “ and check t he state: 9GFORCED PROTECTION MODE ………………………....…… ACTIVE
14. Set the contact on “M” position. The anti starting indicator will start to blink ra pidly.
Check in the “ STATE LIST” if the state “ANTI STARTING” is “ACTIVE”.
15. In the menu “COMMAND MODE” a ccess “ACTUATORS”, then select the command
“ MANUAL CODE INTRODUCTION”. Type t he four fi gures of the repairi ng code, t hen
validate with the key “ENTER”. On the screen the message “COMMAND IN PROGRESS”
w ill appear and then “FINISHED COMMAND”.
16. Set the contact off and then set again the contact on, without starting the engine, in order
to send the new anti starting code to the injection computer. The anti starting indicator will light
for 3 seconds, and then it will turn off.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 16
Procedures
17. The procedure is finished. Check the engine starting with both keys.
REMARK:
For the RF remote control synchronisation, after the replacement of a kit, take into account
the following situations:
- for the first RF remote control, perform the “ SIMPLE SYNCHRONISED PROCEDURE”;
- for t he second RF re m ote control pe rform the “SPE CIFIC SYNCHRONISE D
PROCEDURE”. C. CODE REPAIRING INTRODUCTION PROCEDURE
The repairing code may be introduced only by means of the CLIP tester. This is possible only
if when setting the contact on, the anti starting indicator blinks rapidly, this being confirmed by the
state:
10G ANTI STARTING ……………………………………………….ACTIVE
After getting from DACIA database the repairing code (based on the vehicle chassis series
and on the code from the vehicle’s key head), perform the following operations.
1. Connect the CLIP tester to the diagnostic socket and to the battery (or to the lighter
socket) of the vehicle.
2. The anti start up indicator must blink slowly , the contact being taken off.
3. Set the contact in “M” position. The indicator must blink rapidly.
4. Select vehicle type “B41”;
5. Select the menu “ COMPUTER TEST” then select “ ANTI STARTING”.
6. In the menu “STAT E LIST” find the state 10G “ANTI STARTING” which must be
“ACTIVE”. 7. Access “COMMAND MODE” then select “ACTUATORS”.
8. Select the command “ MANUAL CODE INTRODUCTION” where you will write the
repairi ng c ode (form ed of 4 fi gures), then validate it with t he ke y “ ENTER”. The message
“COMMAND IN PROGRESS” will be displayed followed by the message “FINISHED
COMMAND”. 9. Now the procedure is finished and you may start the vehicle engine.
AT T E N T I ON!
Yo u may perform three attempts of introducing the repairing code; if after the third
essay the code is not yet valid, wait for 15 minutes, take off the contact and then set it
again, then other three attempts may be performed.
REMARK:
This procedure does not decode the injection computer, but is only allowing the start
of the vehicle’s engine. After 10 minutes have passed from the first introduction of the
r epairing code or after the disconnection of the battery, the vehicle’s engine cannot be
s tarted unless a new repairing code is introduced.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 17
Procedures
D. SIMPLE SYNCHRONISED PROCEDURE
This procedure allows the synchronisation of a RF remote control with E.C.U. decoder and
is to be applied in the following situations: -the RF remote control c ode is no longer in the range of the E .C.U. decoder reception,
because of blind consecutive pushing over a 1000 time on the RF remote control button.;
- the replacement of the E .C.U. decoder with a new one;
- the replacement of the RF remote control if the E.C.U. decoder is new (E.C.U. decoder
replacement plus a RF key.);
The following operations will be performed: -take off the contact;
- push and maintain like that for about 5 seconds, the doors locking switch located on the
dashboard ; the doors actuators are performing a closing/opening course;
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system indicator, push twice the RF remote control button; the doors actuators are performing a
closing/opening course;
-the procedure of synchronisation is finished; check the doors blocking/ unlocking by
pushing the RF remote control.
OBSERVAT ION:
During those 10 seconds you can visualise by means of the CLIP tester t he state 17G
“PROGRAMMING OR TIR/TRF RESYNCHRONISATION” which must be ACTIVE.
E. SPECIFIC SYNCHRONISED PROCEDURE
This procedure is used for the synchronisation of the second RF key with E.C.U. decoder
and will be performed as follows:
-connect the CLIP tester to the diagnostic socket and the battery (or the lighter socket)
of the vehicle;
- select the vehicle type “B41”;
- select the menu “ COMPUTERS TEST” then “ ANTI STARTING”;
- enter the menu “COMMAND MODE” and select “CONFIGURATION”;
- validate the command “ PROGRAMMI NG THE SECOND TIR / TRF KEY” launching
the command from the blue button situated on the right top of the screen; the doors actuators are
performing a closing/opening course. - during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system, push twice t he RF remote control button; the doors will block and then unlock and the
anti starting indicator will turn off. The second remote control is now synchronised. Check the
blocking/ unlocking by pushing the RF remote control.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 18
Diag nostic
FA ILURES AND STATES INTERPRETATION
1. FAILURE OF COMMUNICATION CLIP TESTER/ E.C.U. DECODER
RECOMMENDATION Check if the lines K and L are not disturbed by another computer of the vehicle.
Check the condition of fuse F 03 from the cockpit fuse box.
Replace the fuse if necessary.
Check if the CLIP tester is not the cause of the failure; check if the tester is communicating
with another computer of the same vehicle (injection computer).
M easure the tension of the vehicle’s battery (U> 12,3V). If necessary, charge the battery.
Check if the E.C.U. decoder is correctly connected to the vehicle’s wiring.
Check the right supply of the E.C.U. decoder:
-presence of the mass at pin A8 of the E .C.U. decoder
- supply + I.C. at pin A9 of t he E .C.U. decoder
Be sure that the diagnostic socket i s proper supplied, according to the circuit diagram.
Check the continuity and the isolation of the electric wiring on the corresponding pins layout.
E.C.U. decoder A3 7 diagnostic socket
A4 15
If the connection tester CLIP – E.C.U. decoder can’t be established, then replace the decoder.
AFTER REPAIRING After establishing the communication with the tester, fix the
possible failures.
Perform a conformity checking.
{ }
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 19
Diag nostic
2. 4D STATE: + 12 V (+DC) SUPPLY, EXISTENT
RECOMMENDATION Observation : - 4D state = ACTIVE when the contact i s on “M” position;
- 4D state = PASSIVE when the contact is not on “M ”position.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
YES
NO Replace the E.C.U. decoder if its communication with t he tester can not be realised.
Repair the electric wiring on the supply layout to the pin A7 of E.C.U. decoder.
Check the F03 fuse condition.
Replace the fuse if necessary.
Place the contact on “M” position and check the presence of +12V at the pin A7 of the
E.C.U. decoder. Is there +12V?
vnx.su