2004 DACIA SOLENZA warning

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 36
Diag nostic
THE CONFORMITY CHECKING
N ext, the checking of different states and configurations of the anti starting system is to be
performed.
RECOMMENDATION In case of finding some failures at the diagnostic by means of
the CLIP tester, analyse them based on the diagnostic (ALP)
corresponding to the respective failure.
Crt. Function State/ configuration Obse rvations
Nr. 1. Conformity E.C.U decoder. Computer identification Display of the E.C.U. decoder item.
2. Remote control type 2G = remote control IR = infrared configuration RF = radio frequency
3. Ceiling delayed lamp Without ceiling delayed lamp or Validation on the blue button with ceiling delayed lamp on CLIP screen.
4. Key programming 3G = configuration key With one or 2 keys. programming
5. Configuration petrol/ diesel 3D = configuration coded diesel Without = for petrol engine
electric valve. or diesel without electric
valve.
6. Forced starting protection 9D = forced protecting mode ACTIVE = only after validation on the blue button.
7. Anti starting state 10G = anti starting ACTIVE = with the contact
taken off or after 10 seconds
from th e contact taken off.
8. Key presence 8D = key present ACTIVE at the setting on
the contact if there is a
coded key.
REMARK: the states 8D,
9D, 10 D must be ACTIVE
at a correc t operation.
9. Code key receiving 9D = received key code ACTIVE at the setting on
the contact if the key is
coded in a good format.
10. Correct key code 10D = right key code ACTIVE at the setting on the contact if the key is
coded in a good format and
has the correct code.
REMARK: after the analyse
of the states 8D, 9D, 10 D
the contact will be set on
when the LED indicator
b links ( ACTIVE anti
starting).
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 37
Diag nostic
11. Remote control signal reception. 11G = activate the RF remote ACTIVE for 3 secondscontrol. if the decoder
Received signal indication receives the remote control signal.
12. Remote control signal validation 11D = activate the RF remote ACTIVE for 3 sec. control. if the signal received
Good signal indication at the decoder
is good.
13. Communication doors locking 14G = blocking/unlocking ACTIVE wh en the E.C.U.
switch - E.C.U. decoder. decoder receives control from the
doors’ locking switch.
14. Communication E.C.U .decoder - 14D =activation of the doors ACTIVE when the doors actuators actuators E.C.U. decoder
sends the command
blocking/unlocking to
th e actuators of t he doors.
15. The condition of the doors contact 16G = doors contact ACTIVE when the front doors are opened.
16. Remote controls synchronisation 17G = programming ACTIVE when the
in process or resynchronisation TIR/ TRF remote control resynchronisation
procedure is in process.
17. RF remote controls synchronisation 17D = not performed ACTIVE when the not perfor med TIR programming remote control
synchronisation is not
performed.
18. Not performed key code programming 19G = unperformed key ACTIVE when the
programmingkey programming is
not pe rformed.
19. Validated key code programming 19D = unblocked key ACTIVE when the programming validation of the key
programming is not
performed.
20. The programming of the first key. 18G = the memorising of the ACTIVE when the first key programming of the
fir st key is in process.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 38
DISMOUNTING ONE KEY-HEAD
(WITHOUT REMO TE CONTROL).
Place the key-head on a table, the half with
the metal insertion being downwards.
By means of a little screwdriver, act in such
w ay so that scre wdriver point i s supported on
the lower part (D) of the key-head. This will
enable the upper part gliding vis a vis of the lower
part.
DISMOUNT ING ONE KEY-HEAD
(WITH REMO TE CONTROL )
By means of a little s crewdriver, that is
ins erte d in the s lot (E), act by carefully
detach ing from clips the two parts of the key-
head.
D
E
Diagnostic – General
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 39
Diagnostic – General
REMARK : the de coder bushing i s not
coded
DISMOUNTING – REMOUNTING
Dismoun t the half-cases under the steering
wheel, extract the bushing from the starting
contact and disconnect its connector.
CONNE CTING

Pin Denomination 1N ot in use
2 Mass
3+ After contact
4 Outlet signal
DESCRIPTION OF THE SYSTEM
By means of this system, the anti-starting is
activated few seconds after the contact has been
taken off (signalized by the blinking of the anti-
starting red indicator).
Its components are :
〈 key-head, equipped with a coded
electronic circuit (A).
OBSERVATION : the anti-starting
electronic is integrated in the remote control
printed circuit.
〈 anti-starting bushing (B), placed around the
ignition-start ing contact, equipped with an
electronic circuit having the purpose of key code
transmitting to the Cockpit Central Unit (UCH).
A
B
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 40

Cockpit Central Unit
For anti-star ting function , the Cockpit Central Unit is ensuring the following functions:
- key signal decoding
- dialoguing with the injection computer.
- Conducting the anti-starting indicator placed on instrument panel.
- Dialoguin g with the diagnostic tester.
Cockpit Central Unit (C) is placed on the driving post left part, being attached on the dashboard
lateral side, in a protection box.
For dismounting please see Chapter 87.
Anti-starting indicator, placed on instrument panel, it is used to signal:
- anti-starting system activatio n
- key non-recognition
-a system failure
- key programming
C
Diagnostic – General
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 41
DISMOUNTING ONE KEY-HEAD
(WITHOUT REMO TE CONTROL).
Place the key-head on a table, the half with
the metal insertion being downwards.
By means of a little screwdriver, act in such
w ay so that scre wdriver point i s supported on
the lower part (D) of the key-head. This will
enable the upper part gliding vis a vis of the lower
part.
DISMOUNTING ONE KEY-HEAD
(WITH REMO TE CONTROL )
By means of a little s crewdriver, that is
ins erte d in the s lot (E), act by carefully
detach ing from clips the two parts of the key-
head.
D
E
Diagnostic – General
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 42
Diagnostic – General
This document is presenting the diagnostic generally valid for all computers, for anti-starting
function.
In order to perform the diagnostic of t his system, it is then all-i mportant t o dispose of the
following elements: -workshop manual of the corresponding vehicle
- electric diagram of the function, for the correspondin g vehicle
- special tools specified in the column “Necessar y Special tools”.
GENERAL ME THOD OF DIAGNOSTIC
- CLIP tester setting on, in order t o identify the system that is e quipping the vehicle
(identification of the computer family , program number, V. diagnostic..).
- Analysis of the “diagnostic” documents corresponding to the identified system.
- Acknowledgemen t of the information supplied in chapters “General”.
Reading of the memorised failure in the computer memory and taking advantage of the chapter
“Failures interpretatio n”.
Attention : each failure is interpreted for a specific type of memorisation : present failure,
memorised failure, present or memorised failure). The specified checking for handling each
failure are not to be applied on the vehicle unless the declared failure is interpreted in the document
for its specific memorising type. The memorising type must be taken into consideration when the
tester is set on, after setting off and on of the contact. If a failure i s interpreted in t he moment when i t is declare d “memorised”, t he diagnostic
applicatio n conditions are present in “Recommendations”. If the conditions are not fulfilled, yo u
must take the ideas from the diagnostic of damaged element circuit checking, because the failure
is not anymore present on the vehicle. Apply the same method when a failure is declared as been
memorised by the diagnostic tester, but it is interpreted in the documentation only as “present”
failure state.
-Performing the conformity checking (accentuatio n of the possible failures, non-declared
yet by the system self-diagnostic) and application of the adequate diagnostic according to the
results. - Reparation validation (elimination of “client’s effect”)
- Diagnostic exploitation by “Client’s effect” if the problem still on.
NECESSARY SPECIAL TOOLS FOR INTERVENT ION
-CLIP diagnostic tester
- ELE 1622 electric multi-socket
- All-purpose mete
r
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 43
OPERATION
When anti-starting system is on, the red LED is blinking (rare signal: one blink/sec).
After setting the contact on, the key code is transmitted to the Cockpit Central Unit.
If the code is recognized by the Cockpit Central Unit, this one is sending coded signals to the
injection computer and the anti-starting LED is off.
If signals issued by the Cockpit Central Unit and by the injection computer are matching, the
Cockpit Central Unit is authorizing the engine starting and the injection is unlocked.
SPECI AL SI TUATIONS
Injection computer does not have any reference code in m emory: the code sent by UCH is
written in the memory .
If there is no matching of the key c odes / Cockpit Central Unit, t he system is remaining
blocked and anti-star ting LED is blinking (quick signal). The vehicle starting is not authorized.
AT TE NT ION: when the battery is low charged, the voltage drop further to starter
action may reactivate the anti-starting. If voltage is too low, starting is impossible.
Key recognition in normal operation
Anti-starting indicator
Protected vehicle (without + after contact) Indicator slow blinking
Recognized key, non protected injection Indicator lighted for 3 seconds, then set off.
Non-recognized key Indicator is quickly blinking (at 4 Hertz)
Diagnostic – General
vnx.su