Page 301 of 891
FRONT AX LES ELEMENTS
31
31 - 10
Brake caliper
DISMOUNTIN G
Loosen the front wheel attachment screws.
Lift the vehicle by means of a two-column
elevator Dismount the wheel.
Drain the brake fluid from the reservoir
Remove the locks and the caliper wedges.
Un screw the rigid duct screw from the
brake flexible hose and detach the caliper
assembly.
REMARK :
If it is necessary to dismount the
cali per fork, di sm ount the at tachm ent
sc rews on the caliper fork.
When remounting the fork, replace the
Grower washers, tighten the screws to the
r equired moment of 6.5 daNm then seal
them with FIXAMED R 58.
RE PAI R ING
Dismount the protection gasket.
Extract the piston using a wooden wedge and
a compressed air source.
Remove the sealing gasket from its seat in the
caliper groove by means of a blade. Clean with alcohol the parts, replace t he
damaged ones, mounting being performed in the
dismounting reverse order, after previously all
parts have been oiled with brake fluid.
REMARK :
Before remounting on the fork, check the
sealing of t he assembled caliper.
TIGHTENING MOMENTS (d aNm)
Wheel screws 7.5
Rigid duct on fr ont flexible screw 1.5
Purging screw 1
Flexible hose - caliper 1.7
vnx.su
Page 641 of 891
87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 1
It is located on the left side of the climate
control box, being attached by means of a
screw. It has the windscreen washing electric
pump attached on the washer reservoir.
In the drawin g, the following elements may
be identified:
1,2 Pins of the electric pump.
3 Windscreen washing reservoir
4 Electric pump
5 Attachment screw
6W ashing hose
7 Adjustable nozzle
8W ashing reservoir cap
9W ashing bushing
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the climate control gasket.
Dismount the climate control protector.
Di smount the attachment scre w of the
washing reservoir. Carefully remove the front wiring branch
(in order not to damage the splice), from its
location in the wall between the engine
compartment and the climate control box.
Extract the washing reservoir from the
washing b ushing (9). Di
sconnect t he washing hose connected to
the electric pump. Carefully remove the washing reservoir from
the climate control compartmen t and tilt it in such
way that windscreen washing fluid is not flowing
out.
R EMOU NT I NG
Perform the dismounting operations in t he
reverse order.
Check the opera tion of the assembly and
eventually adjust by means of a “needle” the
nozzle in order to correctly wash the windscreen.
AT T E N T I ON!
Do n o t clo se front bonnet after
dismounti ng the w ind scr een w a sh ing
assembly, because it may be possible the
front wiring damaging.
REMARK:
The washing fluid level must be between
the minim and maxim levels marks on the
washing reservoir (0.8 l). The required t ightening m oment of the
attachment screw of the windscreen washing
assembly: 2 Nm.
Connector
Pin Denomination
1 Windscreen washing pump control
2 Mass
Windscreen washing
vnx.su
Page 799 of 891
89
ELECTRIC DIAGRAMS
89 - 6
Functional diagrams list
D OORS CENTRAL LOCKING
ANTI-STARTING
ELECTRIC LIGHTER
CLIMATE CONTROL
CLIMATE CONTROL AND AIR CONDITIONING
CEILING LAMP
FRONT WINDOWS ELECTRIC CONTROL
RADIO
STARTING CIRCUIT
ENGINE CO OLING FAN
ELECTRONIC INJECTION
CHARGING CIRCUIT
REAR WIRING MASS
FRONT WIRING/ DASHBOARD MASS
BATTERY/CARRIAGE BODY MASS
FOG PROJECTORS WIRING MASS
HATCHBACK WIRING MASS
ENGI NE WIRING MASS
COCKPIT FUSE BOX
COCKPIT CENTRAL UNIT (UCH)
ENGINE FU SE BOX AND RELAY
HANDBRAKE INDICATOR / BRAKING SYSTEM FAILURE
FUEL LEVER INDICATOR
OIL PRESSURE INDICATOR
DIAGNOSTIC SOCKET
INST RUMENT PANEL
COOLING FLUID TEMPERATURE ALERT INDICATOR
COOLING FLUID TEMPERATURE INDICATOR
SPEED INDICATOR
DRIVER AIRBAG
ACOUSTIC WARNING
REAR WINDOW DEFROSTING
WINDSCREEN WASHER-WIPER
FOG PROJECTORS
ELECTRIC DI AGRAMS DENOMINATION DIAGRAM NUMBER
1
2
3
4
5
6-7
8
9-10
11
12-13
14-15-16-17-18-19-20-21
22
23
24-25-26-27-28-29-30-31
32
33
34
35-36-37-38
39-40-41-42-43-44-45-46-
47-48-49-50
51-52
53-54-55-56
57
58-59
60
61-62
63-64-65
66
67
68
69
70
71
72
73
vnx.su