2003 NISSAN TEANA Power

GW-74
DOOR MIRROR

DOOR MIRRORPFP:96301
Precautions to Handle Retractable Power Door MirrorsBIS0010G

Do not manually operate retractable power door mirrors. If mirror
is operated manually, be sure to use the retracting switch to
move mirror fully to the opposite direction until it stops. In this
case, a loud click sound is heard, but it is not abnormal. (If mirror
body is manually moved to the neutral position, door mirror will
have some disturbing symptoms during driving, including vibra-
tion, rough retracting movement, or sometimes no retracting.)
CAUTION:
Tilting mirror body forward with excessive force may dam-
age it.

When operating retracting switch to move mirror from the neu-
tral position to the fully-closed (backward limit) position, at the
beginning of the movement a faint click sound is heard, but it is not abnormal.

RH and LH retractable power door mirror bodies have different mounting angles in the neutral position.
This is why the RH mirror body delays slightly when operated with the retracting switch.
NOTE:

When the retractable power door mirror body is in the neutral
position, if retracting switch is operated to the opening direc-
tion while pressing it forward, mirror body is moved to the for-
ward limit position, but it is not abnormal. In this case, be sure
to operate retracting switch to move mirror to the fully-closed
(backward limit) position.

When the retracting switch is operated continuously 5 times
or more, the retractable power door mirror may be inactivated
to prevent overheating. In this case, wait for approximately 5
minutes to recover.
PIIB1148E
PIIB1149E

GW-78
DOOR MIRROR

Disassembly and AssemblyBIS0010J
DISASSEMBLY
1. Pull out all the terminals from the connector.
NOTE:
Before pulling out the terminal, note the connector terminal arrangement.
2. Place the mirror body with mirror glass facing upward.
3. Put a strip of protective tape B on mirror body.
4. As shown in the figure, insert a small slotted screwdriver A into
the recess between mirror base (mirror holder)(1) and mirror
holder bracket (2) and push up two pawls (3) to remove mirror
holder lower half side.
NOTE:
Insert screwdriver into recesses, and push up while rotating
(twist) to make work easier.
CAUTION:
When pushing up the tabs, do not forcibly push up only 1
concave but try to push up using 2 concave positions.
5. Remove terminals of mirror heater attachment.
6. Remove base.
7. Remove door mirror actuator.
8. Remove power unit mounting screws, and disconnect connector.
1. Housing 2. Door mirror actuator 3. Power unit
4. Mirror body (with holder) 5. Connector 6. Base
7. Mirror body cover 8. Door mirror actuator mounting screw 9. Base mounting screw
PIIB1023E
PIIB8320J

DOOR MIRROR
GW-79
C
D
E
F
G
H
J
K
L
MA
B
GW

9. Separate the power unit from the door mirror actuator.
ASSEMBLY
1. Connect power unit connector, and install power unit to door mirror actuator.
2. Install door mirror actuator assembly and base to the housing.
3. Set power unit and mirror body assembly in a horizontal position.
4. Warm the lower tabs with a dryer or equivalent.
NOTE:
Warm the lower tabs sufficiently before installing the mirror body. The tabs may be broken if it is cold. Be
careful especially in winter.
5. Engage upper tabs of mirror glass with power unit. Then, press
lower part of mirror glass down until the lower part snaps to
allow engagement of lower tabs.
NOTE:
After installation, visually check that the lower tabs are securely
engaged when viewed from the bottom of mirror surface.
6. Insert the harness terminals into the connector.
NOTE:
Make sure to insert the harness terminals into the correct con-
nector. Do not confuse the locations.
PIIA6332E

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
CAN (Controller Area Network) . BL-23, BL-48, BL-77,
GW-56
, SE-16
CAN communication EC-113, EC-458, AT-27, CVT-19,
CVT-53
, BL-23, BL-48, BL-77, GW-56, SE-16, WW-9
Canister-See EVAP canister ............... EC-29, EC-369
CHARGE - Wiring diagram ................................ SC-28
Charging system ................................................ SC-27
Chassis and body maintenance ........................ MA-35
CHIME - Wiring diagram ..................................... DI-60
CIGAR - Wiring diagram .................................. WW-60
Cigarette lighter ............................................... WW-60
Circuit breaker ................................................... PG-16
Closed loop control .............................. EC-22, EC-359
Collision diagnosis ........................................... SRS-55
Combination meter ............................................... DI-4
COMM - Wiring diagram ........................ AV-49, AV-73
Component Location (auto A/C) ...................... ATC-36
Compression pressure(QR20DE) ...................... EM-65
Compression pressure(VQ23DE and VQ35DE) ...........
EM-210
Compressor clutch removal and installation .. ATC-136
Compressor special service tool ...................... ATC-15
Condenser ..................................................... ATC-142
Connecting rod bearing clearance(QR20DE) .. EM-105
Connecting rod bearing clearance(VQ23DE and
VQ35DE) ......................................................... EM-251
Connecting rod bushing clearance(QR20DE) . EM-101
Connecting rod bushing clearance(VQ23DE and
VQ35DE) ......................................................... EM-247
Connecting rod(QR20DE) ............................... EM-101
Connecting rod(VQ23DE and VQ35DE) ......... EM-247
CONSULT-II for engine ....................... EC-80, EC-425
CONSULT-II Reference value (CVT) .............. CVT-43
Control units (terminal arrangement) ................. PG-74
Control valve (CVT) ......................................... CVT-23
Controller Area Network (CAN) . BL-23, BL-48, BL-77,
GW-56
, SE-16
Converter housing installation ............ AT-244, AT-355
COOL/F - Wiring diagram .................. EC-222, EC-579
Coolant mixture ratio ......................................... MA-15
Coolant replacement(QR20DE) ......................... MA-16
Coolant replacementVQ35DE ........................... MA-25
Cooling circuit (engine)(QR20DE) ....................... CO-8
Cooling circuit (engine)(VQ32DE and VQ35DE) CO-32
Cooling fan control ........................................... EC-575
Cooling fan motor ............................................ EC-575
Cooling fan relay .............................................. EC-575
Cooling fan(QR20DE) ........................................ CO-20
Cooling fan(VQ23DE and VQ35DE) .................. CO-44
Cowl top ............................................................... EI-21
Cowl top cover ..................................................... EI-21
Crankcase ventilation system - See Positive crankcase
ventilation ............................................ EC-30
, EC-370
Crankshaft position sensor (POS) ..... EC-169, EC-517
Crankshaft(QR20DE) ...................................... EM-104
Crankshaft(VQ23DE and VQ35DE) ................ EM-251
Crash zone sensor .......................................... SRS-44
CVT air breather hose ................................... CVT-186
CVT control system ......................................... CVT-16
CVT cross-sectional view ................................ CVT-15
CVT Electrical parts location ............................ CVT-30
CVT fluid checking ................ CVT-13, CVT-32, MA-36
CVT Fluid Cooler ........................................... CVT-189
CVT fluid replacement ........................ CVT-14, MA-38
CVT fluid temparature sensor .......................... CVT-69
CVT hydraulic control system .......................... CVT-17
CVT indicator ...................................................... DI-52
CVT self-diagnoses ......................................... CVT-47
CVT shift lock system .................................... CVT-180
CVT trouble diagnoses .................................... CVT-24
CVTIND - Wiring diagram ................................... DI-52
Cylinder block boring(QR20DE) ..................... EM-104
Cylinder block(QR20DE) .................................. EM-81
Cylinder block(VQ23DE and VQ35DE) .......... EM-228
Cylinder head bolt tightening(QR20DE) ........... EM-68
Cylinder head bolt tightening(VQ23DE and VQ35DE) .
EM-213
Cylinder head(QR20DE) ................................... EM-65
Cylinder head(VQ23DE and VQ35DE) ........... EM-210
D
D/LOCK - Wiring diagram .................................. BL-25
Diagnosis sensor unit ..................................... SRS-47
Diagnostic trouble code (DTC) for OBD system EC-10,
EC-34
, EC-347, EC-375
Diagnostic trouble code (DTC) inspection priority chart
EC-58
, EC-400, CVT-24
Differentil side oil seal .................................... CVT-187
Display and amp.assembly ............... ATC-44, ATC-56
Display Control Unit ........................................... AV-61
Display Unit ........................................................ AV-41
Door glass ........................................... GW-46, GW-50
Door glass Fitting Adjustment(Front) ................ GW-49
Door glass Fitting Adjustment(Rear) ................. GW-53
Door lock .......................................................... BL-123
Door mirror .......................................... GW-74, GW-77
Door trim ............................................................. EI-35
Door, front ........................................... BL-119, GW-46
Door, rear ............................................ BL-119, GW-50
Drive belt inspection(QR20DE) ......................... MA-16
Drive belt inspection(VQ23DE and VQ35DE) ... MA-24
Drive belt(QR20DE) .......................................... EM-14
Drive belt(VQ23DE and VQ35DE) .................. EM-128
Drive shaft ......................................................... MA-43
Driver air bag .................................................. SRS-35
Dropping resistor (A/T) .................................... AT-132
Duct and grilles .............................................. ATC-126
E
ECM input/output signal ....................... EC-72
, EC-415
ECM power supply EC-106, EC-193, EC-451, EC-541
ECM/PW - Wiring diagram ................. EC-194, EC-542
ECTS - Wiring diagram ...................... EC-133, EC-476
Electric sunroof .................................................. RF-10
Electric throttle control actuator ........ EC-197, EC-200,
EC-213
, EC-552, EC-555

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Heated oxygen sensor 1 (bank 2) .... EC-486, EC-496,
EC-696
Heated oxygen sensor 1 heater ...................... EC-308
Heated oxygen sensor 1 heater (bank 1) ........ EC-706
Heated oxygen sensor 1 heater (bank 2) ........ EC-706
Heated oxygen sensor 2 .................................. EC-313
Heated oxygen sensor 2 (bank 1) ..... EC-714, EC-723
Heated oxygen sensor 2 (bank 2) ..... EC-714, EC-723
Heated oxygen sensor 2 heater ...................... EC-319
Heated seat ....................................................... SE-61
Heater and cooling unit (Heater core) ........... ATC-119
HFC134a (R134a) system precaution ............... ATC-5
HFC134a (R134a) system service procedure ATC-131
HFC134a (R134a) system service tools .......... ATC-16
HFC134a system service equipment precaution ..........
ATC-12
HLC - Wiring diagram ...................................... WW-43
HO2S1 - Wiring diaram ..................... EC-145, EC-152
Horn ................................................................. WW-62
HORN - Wiring diagram ................................... WW-62
How to erase DTC for OBD system ..... EC-35, EC-376
HSEAT - Wiring diagram ................................... SE-70
I
IATSEN - Wiring diagram .................. EC-325
, EC-731
Idle air volume learning ....................... EC-47, EC-389
Idle speed .............................. EC-40, EC-381, EC-387
Ignition coil ......................................... EC-329, EC-735
Ignition coil(QR20DE) ........................................ EM-31
Ignition coil(VQ23DE and VQ35DE) ................ EM-152
Ignition control system ....................... EC-329, EC-735
Ignition timing ........................ EC-40, EC-381, EC-387
IGNSYS - Wiring diagram .................. EC-330, EC-736
In vehicle sensor ............................. ATC-99, ATC-110
INF/D - Wring diagram ........................... AV-43, AV-65
INJECT - Wiring diagram ................... EC-290, EC-685
Injector ............................................... EC-289, EC-684
Input/Output signal of TCM .............................. CVT-19
Instrument panel .................................................. IP-10
INT/L - Wiring diagram ..................................... LT-217
Intake air temperature sensor ............ EC-324, EC-730
Intake door control linkage adjustment ............ ATC-71
Intake door motor ........................... ATC-69, ATC-117
Intake manifold collector(VQ23DE and VQ35DE) ........
EM-133
Intake manifold(QR20DE) ................................. EM-19
Intake manifold(VQ23DE and VQ35DE) ......... EM-138
Intake sensor ................................ ATC-105, ATC-112
Intake valve timing control ............................... EC-116
Intake valve timing control (Bank 1) ................ EC-461
Intake valve timing control (Bank 2) ................ EC-461
Intake valve timing control solenoid valve (Bank 1) ......
EC-545
Intake valve timing control solenoid valve (Bank 2) ......
EC-545
Interior ................................................................. EI-38
Interior lamp ........................................ LT-217, LT-219
IPDM (Intelligent power distribution module engine room) ................................................................. PG-17
IVC - Wiring diagram ....................................... EC-119
IVCB1 - Wiring diagram ................................... EC-546
IVCB2 - Wiring diagram ................................... EC-548
K
Knock sensor (KS) ............................. EC-164
, EC-512
KS - Wiring diagram ........................... EC-165, EC-513
L
L/USSV - Wiring diagram ............................... CVT-148
LAN system circuit ........................................... ATC-59
LCD display ....................................................... AV-61
Line pressure and secondary pressure control CVT-20
Line pressure solenoid valve .......... CVT-97, CVT-102
Line pressure test (A/T) ..................................... AT-46
Liquid gasket application(QR20DE) ........... EM-6, LU-3
Liquid gasket application(VQ23DE and VQ35DE) ........
EM-120
, LU-15, CO-3, CO-27
Location of electrical units ................................. PG-67
Lock-up and select control ............................... CVT-21
Lock-up select solenoid valve ........................ CVT-147
LPSV - Wiring diagram ...................... AT-127, CVT-98
Lubricant (R134a) A/C ..................................... ATC-21
Lubricants ......................................................... MA-14
Lubrication circuit (engine)(QR20DE) .................. LU-5
Lubrication circuit (engine)(VQ23DE and VQ35DE) .....
LU-17
Lubrication oil A/C .......................................... ATC-150
M
MAFS - Wiring diagram ..................... EC-126
, EC-468
Magnet clutch ................................. ATC-78, ATC-136
MAIN - Wiring diagram ........ EC-106, EC-451, AT-158
Maintenance (engine)(VQ23DE and VQ35DE) MA-24
Malfunction indicator (MI) .................... EC-36, EC-377
Mass air flow sensor (MAFS) ............. EC-124, EC-466
Meter ..................................................................... DI-4
METER - Wiring diagram .................................... DI-10
MIL data link connectors circuit ......... EC-344, EC-763
MIL/DL - Wiring diagram .................... EC-344, EC-763
Mirror, door ......................................... GW-74, GW-77
Mirror, out side .................................... GW-74, GW-77
MMSW - Wiring diagram ................................ CVT-114
Mode door control linkage adjustment ............. ATC-65
Mode door motor ............................ ATC-63, ATC-123
Molding - See Exterior EI-25, EI-27, EI-28, EI-29, EI-30
Mud guard - See Exterior .................................... EI-24
Multiport fuel injection (MFI) system .... EC-21, EC-358
Multiport fuel injection precautions ....................... GI-6
N
NATS - Wiring diagram .................................... BL-143
NATS (Nissan anti-theft system) precautions ....... GI-3
NONDTC - Wiring diagram .............. AT-168, CVT-160

IDX-6
ALPHABETICAL INDEX
NVH troubleshooting (BR) ................................... BR-5
NVH troubleshooting (EM)(QR20DE) ............... EM-12
NVH troubleshooting (EM)(VQ23DE and VQ35DE) .....
EM-126
O
O2S1B1 - Wiring diagram .................. EC-488
, EC-498
O2S1B2 - Wiring diagram .................. EC-490, EC-500
Oil cooler (engine)(VQ23DE and VQ35DE) ....... LU-23
Oil filter(QR20DE) .............................................. LU-10
Oil filter(VQ23DE and VQ35DE) ........................ LU-22
Oil pan (engine)(QR20DE) ............................... EM-26
Oil pan (engine)(VQ23DE and VQ35DE) ....... EM-145
Oil pressure (engine)(QR20DE) .......................... LU-7
Oil pressure (engine)(VQ23DE and VQ35DE) .. LU-20
Oil pump (engine)(QR20DE) ............................. LU-11
Oil pump (engine)(VQ23DE and VQ35DE) ....... LU-25
Oil pump regulator valve (engine)(QR20DE) ..... LU-11
Oil pump regulator valve (engine)(VQ23DE and
VQ35DE) ........................................................... LU-25
Oil seal replacement (engine)(QR20DE) ......... EM-53,
EM-62
, EM-70, EM-81
Oil seal replacement (engine)(VQ23DE and VQ35DE)
EM-207
On board diagnostic system ................ EC-33, EC-373
Out side mirror .................................... GW-74, GW-77
Overheat ............................................ EC-218, EC-575
Oversize piston(QR20DE) .............................. EM-103
Oversize piston(VQ23DE and VQ35DE) ........ EM-249
OVRCSV - Wiring diagram .............................. AT-101
P
Park/Neutral position switch .............. EC-238
, EC-614
Park/neutral position switch (A/T) ...... AT-161, AT-210
Park/neutral position switch (CVT) .................. CVT-62
PCV (positive crankcase ventilation) ... EC-30, EC-370
PHASE - Wiring diagram ................................. EC-178
PHSB1 - Wiring diagram .................................. EC-526
PHSB2 - Wiring diagram .................................. EC-528
Pilot bushing replacement - See Pilot
converter(QR20DE) .......................................... EM-81
Pilot bushing replacement - See Pilot
converter(VQ23DE and VQ35DE) .................. EM-228
Piston assembly(QR20DE) ............................... EM-92
Piston assembly(VQ23DE and VQ35DE) ....... EM-240
Piston pin inspection(QR20DE) ........................ EM-99
Piston pin inspection(VQ23DE and VQ35DE) EM-245
Piston ring inspection(QR20DE) ..................... EM-100
Piston ring inspection(VQ23DE and VQ35DE) EM-246
Piston to bore clearance(QR20DE) ................ EM-103
Piston to bore clearance(VQ23DE and VQ35DE) ........
EM-249
PNP/SW - Wiring diagram .. EC-239, EC-615, CVT-64
POS - Wiring diagram ........................ EC-171, EC-519
POWER - Wiring diagram ................... CVT-135, PG-4
Power door mirror .............................................. BL-21
Power seat ......................................................... SE-59
Power steering fluid level .................................. MA-42
Power steering gear ........................................... PS-17
Power steering oil pump .................................... PS-29
Power steering pressure (PSP) sensor .......... EC-185,
EC-533
Power supply routing .......................................... PG-3
Power window .................................................. GW-17
Precations for Leak detection dye .................. ATC-14
Precautions (General) ........................................... GI-4
Pressure control solenoid valve A .. CVT-97, CVT-102
Pressure control solenoid valve B CVT-105, CVT-108
Pressure test (CVT) ........................................ CVT-33
PRGVLV - Wirng diagram ................. EC-283, EC-678
Primary pressure sensor ............................... CVT-126
Primary Speed Sensor .................................... CVT-74
PRIPS - Wiring diagram ................................ CVT-127
PRSCVT - Wiring diagram .............................. CVT-75
PS/SEN - Wiring diagram ................. EC-186, EC-534
PT/SEN - Wiring diagram ................................ AT-121
R
R/FOG - Wiring diagram .................................. LT-144
Radiator(QR20DE) ............................... CO-13, CO-16
Radiator(VQ23DE and VQ35DE) ..................... CO-37
Radio - See Audio .................................... AV-4, AV-18
Rear bumper ....................................................... EI-17
Rear disc brake .................................................. BR-33
Rear door ............................................ BL-119, GW-50
Rear parcel shelf finisher .................................... EI-43
Rear seat ......................................................... SE-112
Rear window defogger ..................................... GW-54
Refrigerant connection precaution .................... ATC-6
Refrigerant discharging evacuating charging ATC-131
Refrigerant general precaution ......................... ATC-6
Refrigerant lines ............................................ ATC-131
Refrigerant pressure sensor EC-339, EC-748, ATC-83,
ATC-144
Refrigeration cycle .......................................... ATC-19
Removal and installation (A/T) ......................... AT-241
Road test ......... AT-48, AT-50, AT-51, AT-52, CVT-35
Rocker cover(QR20DE) .................................... EM-39
Rocker cover(VQ23DE and VQ35DE) ............ EM-160
Room lamp - See Interior lamp ........................ LT-219
ROOM/L - Wiring diagram ............................... LT-225
RP/SEN - Wiring diagram ................. EC-340, EC-749
RRO2 - Wiring diagram .................... EC-314, EC-320
RRO2B1 - Wiring diagram ................ EC-715, EC-724
RRO2B2 - Wiring diagram ................ EC-717, EC-726
S
SEAT - Wiring diagram ...................................... SE-59
Seat belt pre-tensioner disposal ..................... SRS-48
Seat belt, front ..................................................... SB-3
Seat, rear ......................................................... SE-112
Secondary pressure sensor .......................... CVT-118
Secondary Speed Sensor ............................... CVT-79
SECPS - Wiring diagram .............................. CVT-119

TROUBLE DIAGNOSIS
LAN-7
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
MA
B
LAN

TROUBLE DIAGNOSISPFP:00004
Condition of Error DetectionBKS0040T
“U1000” or “U1001” is indicated on SELF-DIAG RESULTS on CONSULT-II if CAN communication signal is not
transmitted or received between units for 2 seconds or more.
CAN COMMUNICATION SYSTEM ERROR

CAN communication line open (CAN-H, CAN-L, or both)

CAN communication line short (ground, between CAN communication lines, other harnesses)

Error of CAN communication control circuit of the unit connected to CAN communication line
WHEN INDICATED “U1000” OR “U1001” IS INDICATED EVEN THOUGH CAN COMMUNICA-
TION SYSTEM IS NORMAL

CONSULT-II CONVERTER not connected: Error may be detected by the self-diagnosis when not using
CONSULT-II CONVERTER (Depending on the control unit which carries out CAN communication).

Removal/installation of parts: Error may be detected when removing and installing CAN communication
unit and related parts while turning the ignition switch ON. (A DTC except for CAN communication may be
detected.)

Fuse blown out (removed): CAN communication of the unit may cease.

Voltage drop: Error may be detected if voltage drops due to discharged battery when turning the ignition
switch ON (Depending on the control unit which carries out CAN communication).

Error may be detected if the power supply circuit of the control unit, which carries out CAN communica-
tion, malfunctions (Depending on the control unit which carries out CAN communication).

Error may be detected if reprogramming is not completed normally.
NOTE:
CAN communication system is normal if “U1000” or “U1001” is indicated on SELF-DIAG RESULTS of CON-
SULT-II under the above conditions. Erase the memory of the self-diagnosis of each unit.

LAN-26
[CAN FUNDAMENTAL]
TROUBLE DIAGNOSES WORK FLOW

Present Error — Open Circuit —
Identify the error circuit using information from the “SELECT SYSTEM” and “CAN DIAG SUPPORT MNTR”
screens.
1. SELECT SYSTEM: Check the items indicated in “SELECT SYSTEM”. Draw a line on the diagnosis sheet
to indicate the error circuit.
NOTE:
CAN communication line has no error if units other than Diag on CAN units are indicated. An error may be
on the power supply of the control unit, DDL1 line or DDL2 line.
a. “TRANSMISSION” which is Diag on CAN unit, is not indicated on “SELECT SYSTEM” screen. This indi-
cates that DLC is not receiving a signal from TCM. Draw a line to indicate an error between DLC and
TCM (line 1-a in the figure).
NOTE:

Diag on CAN units are not indicated on the “SELECT SYSTEM” screen when the CAN line between
Diag on CAN unit and the data link connector is open.

For a description of Diag on CAN, refer to LAN-6, "Diag on CAN" .
SKIB8892E