2003 NISSAN TEANA instrument panel

IP-12
INSTRUMENT PANEL ASSEMBLY

REMOVAL
(A) Kicking Plate (LH/RH)
Remove kicking plate. Refer to EI-39, "FRONT KICKING PLATE INNER" .
(B) Front Pillar Garnish (LH/RH)
Pull toward vehicle inside to disengage metal clip. Refer to EI-39, "FRONT PILLAR GARNISH" .
(C) A/T Selector Lever Knob
1. Remove selector knob cover and lower downward.
2. Remove lock pin, and then pull out selector knob and cover upward. Refer to AT- 2 1 3 , "
Control Device
Removal and Installation" .
(D) A/T Console Finisher
1. Place the selector lever in “D” position.
2. Open front ashtray lid and cup holder lid and insert a remover
into the gap of A/T console finisher rear to disengage metal
clips, and then disconnect harness connector while lifting up.
(E) Console Switch Finisher
1. Remove metal clip.
2. Disconnect harness connector and then remove console switch
finisher.
(F) Front Ashtray
Insert a remover into the front ashtray rear gap to disengage metal
clips, and then disconnect harness connector while lifting up.
PIIB1777E
PIIB1778E
PIIA6349E

INSTRUMENT PANEL ASSEMBLY
IP-13
C
D
E
F
G
H
J
K
L
MA
B
IP

(G) Instrument Panel Lower Cover (LH/RH)
Insert a remover into the gap between instrument panel lower cover
(LH/RH) and floor carpet. Disengage and pull forward metal clips.
(H) Instrument Panel Stay Cover
1. Remove instrument panel stay cover mounting screw securing
center console front end and bottom of instrument panel & pad
center.
2. Lift up the bottom of instrument panel stay cover and pull it for-
ward to remove.
CAUTION:
Wrap protection tape around metal fittings on the receiving
side of lower screw, and prevent them from being damaged
by contacting.
(I) Console Rear Cover
1. Remove rear ashtray.
2. Insert a remover into the gap between console rear cover and
console body, and then disengage and pull rearward metal clips.
PIIA6353E
PIIA6354E
PIIA7083E
PIIA6365E

IP-14
INSTRUMENT PANEL ASSEMBLY

(J) Center Console
1. Remove A/T control device assembly RH mounting screws.
2. Remove console body rear end lower mounting screws.
3. Lift up center console from rear and disconnect interior antenna (center console) harness connector, and
then remove center console so that console front end joint does not contact.
(K) Instrument Passenger Lower Panel
1. Remove lower mounting screw while glove box lid is closed.
2. Remove upper mounting screw while glove box lid is open, and
then remove glove box striker.
3. Pull glove box illumination harness connector forward to disconnect after disengaging pawls, and then
remove instrument passenger lower panel.
(L) Instrument Panel Finisher (C/D)
1. Insert a remover (first) into the gap between cluster lid D and
display, and then make the gap between instrument panel fin-
isher C/D and instrument panel & pad.(With display model)
PIIB1779E
PIIA6366E
PIIB1780E
PIIB1781E

INSTRUMENT PANEL ASSEMBLY
IP-15
C
D
E
F
G
H
J
K
L
MA
B
IP

2. Insert another remover (second) into the gap between instru-
ment panel finisher C/D and instrument panel & pad, and then
pull out remover (first).
3. Insert remover (first) into the gap between instrument panel fin-
isher while pressing cluster lid D, and then pull out remover
(second). Pull instrument panel finisher forward using remover
(first) to remove.
(M) Cluster Lid C
1. Remove screws.
2. Disconnect harness connector, and then remove cluster lid C.
3. Disassemble A/C controller and audio unit.
Refer to ATC-107, "
A/C CONTROLLER" .
Refer to AV- 1 5
. (With Integrated Display System)
Refer to AV- 3 4
. (With Integrated Color Display System)
(N) Cluster Lid D
1. Remove screws, and then disengage metal clips to remove.
2. Disconnect hazard switch harness connector, and then remove cluster lid D.
PIIB1782E
PIIB1783E
PIIB1784E
PIIB1785E

IP-16
INSTRUMENT PANEL ASSEMBLY

(O) Display Unit
Remove screws, and then disconnect harness connector to remove
display.
Refer to AV- 6 0
. (With Integrated Display System)
Refer to AV- 11 2
. (With Integrated Color Display System)
CAUTION:
Be careful when handling so as not to damage by contacting
with related parts.
(P) Fuse Block Lid
Hang a finger on the lower part of fuse block lid and pull out forward.
(Q) Instrument Driver Lower Panel
1. Remove screws.
2. Remove data link connector.
3. Pull the panel forward horizontally, and then disengage metal
clip to remove.
4. Disconnect in-vehicle sensor connector and each switch con-
nector.
5. Remove hood lock control.
(R) Steering Lock Escutcheon
Insert a remover into the gap around steering lock escutcheon, and
then pull toward vehicle outside.
(S) Steering Column Upper / Lower Cover
1. Tilt up steering column.
2. Remove screws.
3. Disengage pawls to remove.
(T) Instrument Panel Pad A
1. Tilt down steering column.
2. Insert a remover into the gap between instrument panel pad A
and instrument panel & pad, and then disengage metal clips to
remove.
PIIB1786E
PIIB1787E
PIIA6370E
PIIB1788E

INSTRUMENT PANEL ASSEMBLY
IP-17
C
D
E
F
G
H
J
K
L
MA
B
IP

(U) Cluster Lid A
1. Remove screws.
2. Insert a remover into the gap between cluster lid A and instru-
ment panel & pad, and then disengage and pull forward metal
clips.
(V) Combination Meter
1. Hold and pull forward combination meter after removing screws.
2. Disconnect harness connector, and then remove combination
meter so as to prevent it from contacting with related parts.
(W) Instrument Panel Pad B
Remove screws from back, and then remove instrument panel pad B
from front surface forward.
(X) Instrument Passenger Upper Panel
1. Remove screws from back.
2. Disengage metal clips from front side, and then pull out instru-
ment passenger upper panel forward.
(Y) Instrument Panel & Pad
1. Remove screw and nut.
2. Remove passenger air bag module bolts. Refer to SRS-39, "
FRONT PASSENGER AIR BAG MODULE" .
3. Remove combination meter harness clips from back of combination meter mounting part.
4. Remove fuse block from bottom of instrument panel & lid RH.
5. Disconnect illumination harness connector for front ashtray from back of cluster lid C mounting part.
PIIB1789E
PIIB1790E
PIIB1791E
PIIB1792E

IP-18
INSTRUMENT PANEL ASSEMBLY

6. Disconnect sunload sensor, auto light sensor, and security indicator harness connectors. Refer to AT C -
111 , "SUNLOAD SENSOR" and LT- 7 4 , "Removal and Installation for Optical Sensor" .
7. Remove instrument panel & pad from passenger side door opening.
8. Remove screws, and then remove instrument panel pad from instrument panel.
(Z) Instrument Center Lower Panel
1. Remove screws from back of instrument panel & pad.
2. Remove instrument center lower panel forward from front side.
INSTALLATION
Install in the reverse order of removal.

INSTRUMENT PANEL ASSEMBLY
IP-19
C
D
E
F
G
H
J
K
L
MA
B
IP

Disassembly and AssemblyBIS00128
CENTER CONSOLE
Disassembly
1. Remove screws, and remove instrument panel stay cover.
2. Insert a screwdriver wrapped with tape into the gap around con-
sole mask, and then disengage pawls and remove console
mask.
3. Remove screws and harness clips from rear of cup holder back, and then remove inside key antenna-1.
4. Remove rear screws from back, and remove cup holder.
5. Open console lid and remove screws, and then remove console lid.
6. Insert a remover into the gap around box finisher, and then disengage clips and remove box finisher.
7. Remove screws, and then remove console finisher (LH/RH).
1. Console box 2. Console finisher (RH) 3. Screw
4. Box finisher 5. Instrument panel stay cover 6. Console body
7. Console finisher (LH) 8. Cup holder 9. Inside key antenna-1
10. Console bracket 11. Console lid 12. Console mask
PIIB0599E
PIIA6350E