2003 NISSAN TEANA instrument panel

IP-20
INSTRUMENT PANEL ASSEMBLY

8. Remove screws, and then remove console box.
9. Remove screws from both sides of bottom of rear end, and then remove console bracket.
Assembly
Assemble in the reverse order of disassembly.
INSTRUMENT PASSENGER LOWER PANEL
Disassembly
1. Remove caught point of tip of damper from back of glove box lid
side using a screwdriver wrapped with tape.
2. Remove screws from center of back surface, and then remove damper body.
3. Remove glove box pin from center of back surface using a
screwdriver wrapped with tape, and then remove glove box from
instrument passenger lower panel.
4. Remove illumination from back surface upper using a screwdriver wrapped with tape.
1. Pocket 2. Instrument passenger lower panel 3. Glove box pin
4. Glove box 5. Damper 6. Screw
7. Glove box illumination
PIIB1793E
PIIB1794E
PIIA6352E

INSTRUMENT PANEL ASSEMBLY
IP-21
C
D
E
F
G
H
J
K
L
MA
B
IP

5. Remove screws, and then remove pocket.
Assembly
Assemble in the reverse order of disassembly.
CLUSTER LID D
Disassembly
1. Remove screws, and then remove instrument upper box.
2. Disconnect pawls, and then remove center ventilator grille. Refer to ATC-126, "
Removal of Center Ventila-
tor Grilles" .
Assembly
Assemble in the reverse order of disassembly.
PIIB0640E
1. Screw 2. Instrument upper box 3. Center ventilator grille
4. Cluster lid D
PIIB0603E

IP-22
INSTRUMENT PANEL ASSEMBLY

LT-74
AUTO LIGHT SYSTEM

Removal and Installation for Optical SensorBKS001OK
REMOVAL
1. Remove instrument panel. Refer to IP-10, "INSTRUMENT
PANEL ASSEMBLY" .
2. Disconnect optical sensor connector.
3. Remove optical sensor.
INSTALLATION
Installation is the reverse order of removal.
SKIB0895E

HEADLAMP AIMING CONTROL (MANUAL)
LT-125
C
D
E
F
G
H
I
J
L
MA
B
LT

Removal and InstallationBKS001ON
REMOVAL
1. Remove instrument driver lower panel. Refer to IP-10,
"INSTRUMENT PANEL ASSEMBLY" .
2. Press pawl on reverse side and remove the headlamp aiming
switch.
INSTALLATION
Installation is the reverse order of removal.
Switch Circuit InspectionBKS001OO
Using a circuit tester, check continuity between the headlamp aiming
switch connector terminals in each operation status of the aiming
switch.
SKIB0896E
SKIB8648J

LT-176
LIGHTING AND TURN SIGNAL SWITCH

LIGHTING AND TURN SIGNAL SWITCHPFP:25540
Removal and InstallationBKS001Q4
REMOVAL
1. Remove steering column cover. Refer to IP-10, "INSTRUMENT
PANEL ASSEMBLY" .
2. While pressing pawls in direction as shown in the figure, pull
lighting and turn signal switch toward driver door and disconnect
from the base.
INSTALLATION
Installation is the reverse order of removal.
Switch Circuit InspectionBKS001Q5
Refer to LT- 1 8 5 , "Combination Switch Inspection" .
SKIB0899E

HAZARD SWITCH
LT-177
C
D
E
F
G
H
I
J
L
MA
B
LT

HAZARD SWITCHPFP:25290
Removal and InstallationBKS001Q6
REMOVAL
1. Remove cluster lid D. Refer to IP-10, "INSTRUMENT PANEL
ASSEMBLY" .
2. Disconnect connector.
3. Remove screw and remove hazard switch integral with center
ventilator grille from cluster lid D.
4. Pawl on rearward and remove hazard switch.
INSTALLATION
Installation is the reverse order of removal.
PKIB7984E

LT-242
INTERIOR ROOM LAMP

IGNITION KEYHOLE ILLUMINATION
1. Remove steering column cover. Refer to IP-10, "INSTRUMENT
PANEL ASSEMBLY" .
2. Remove screw, and remove NATS antenna amp.
3. Pull out ring and turn bulb socket to left to release lock.
Removal and InstallationBKS001RF
MAP LAMP
Removal
1. Insert a clip driver or suitable tool and disengage the pawl fit-
tings the map lamp.
2. Disconnect map lamp connector and remove map lamp.
Installation
Installation is the reverse order of removal.
STEP LAMP
Removal
1. Insert a clip driver or a suitable tool and remove lens and bulb
housing.
2. Disconnect step lamp connector.
Installation
Installation is the reverse order of removal.Ignition keyhole illumination : 14V - 1.4W
SKIA6362E
SKIA8659E
SKIB0900E