2003 NISSAN TEANA roof

EI-26
ROOF SIDE MOLDING

4. Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
[Press-fit limit:19.6 N (2 kg, 4.4 lb) × 2 seconds)]
5. Tape clips after press fit, and temporarily hold it for specified time based on the following.

5 to 10 °C (41 to 50 °F) ---1 hour or more

11 to 23 °C (52 to 73 °F) ---30 minutes or more

24 °C or more (75 °F or more) ---15 minutes or more
6. Install from roof side molding rear end to front end in this order after temporarily holding.
CAUTION:

Use double-faced adhesive tape after hardening for clips.

Securely insert molding rear end cap onto roof rear end cutout (installation standard).

Press in after making sure that body side fastener molding is securely inserted when installing
windshield clips.

Do not wash the vehicle within 24 hours so as to keep adhesive.

EI-28
WINDSHIELD MOLDING

WINDSHIELD MOLDINGPFP:72700
Removal and InstallationBIS0011M
REMOVAL AND INSTALLATION
Refer to GW-11, "Removal and Installation" in GW section for removal and installation of windshield and wind-
shield molding.
PIIB1021E
1. Dam rubber 2. Windshield upper molding 3. Roof side molding
4. Fastener (LH/RH) 5. Windshield glass 6. Spacer
7. Roof 8. Panel 9. Adhesive
10. Front pillar outer panel 11. Cowl top cover (LH/RH) 12. Cowl box side

REAR WINDOW MOLDING
EI-29
C
D
E
F
G
H
J
K
L
MA
B
EI

REAR WINDOW MOLDINGPFP:79762
Removal and InstallationBIS0011N
REMOVAL AND INSTALLATION
Refer to GW-15, "Removal and Installation" in GW section for removal and installation of rear window glass
and molding.
PIIB1022E
1. Rear window glass 2. Spacer 3. Rear window molding
4. Dam rubber 5. Adhesive 6. Roof panel outer
7. Trunk lid outer panel

HEADLINING
EI-55
C
D
E
F
G
H
J
K
L
MA
B
EI

REMOVAL
1. Remove front seat belt floor anchor bolt and rear seat belt floor ancher bolt. Refer to SB-3, "SEAT BELTS"
and SB-5, "Removal and Installation of Rear Seat Belt" .
2. Remove rear seat. Refer to SE-112, "
REAR SEAT" .
3. Remove front pillar garnish (LH/RH). Refer to EI-38, "
BODY SIDE TRIM" .
4. Remove roof harness securing clip using a clip clamp remover
after removing, and then disconnect roof harness connector.
5. Remove front kicking plate inner, center pillar lower garnish, center pillar upper garnish, front body side
welt, rear kicking plate inner, rear seatback finisher, rear pillar finisher, and rear body side welt. Refer to
EI-38, "
BODY SIDE TRIM" .
6. Remove mounting clips of front assist grip (RH) and rear assist
grip (LH/RH).
7. Remove sun-visor (LH/RH) mounting screws.
NOTE:
Disconnect vanity mirror illumination harness connector when removing sun-visor.
1. Clip (C101) 2. Headlining (standard model) 3. Rear assist grip (RH)
4. Personal lamp (RH) 5. Roof harness securing clip 6. Roof harness connector
7. Sun-visor (RH) 8. Sun-visor holder (RH) 9. Screw
10. Cap (RH) 11. Spot lamp (map lamp) 12. Sun-visor holder (LH)
13. Cap (LH) 14.Vanity mirror illumination harness con-
nector15. Sun-visor (LH)
16.Spot lamp(map lamp) harness
connector (standardmodel)17. Metal clip 18. Dual lock fastener (with sunroof model)
19.Harness connector for hands-
free phone microphone
(model with car wings unit)20.Roof harness securing tape (standard
model)21. Front assist grip (RH)
22. Personal lamp (LH) 23. Rear assist grip (LH) 24. Clip holder
25.Headlining (model with sun-
roof)26.Sunroof motor harness connector
(model with sunroof)27. Front roof finisher (model with sunroof)
28.Roof hook (model with sun-
roof)
PIIA7118E
PIIA6267E

EI-56
HEADLINING

8. Remove sun-visor holder (LH/RH).
NOTE:
Insert a screwdriver into the cutout and rotate 90 degrees to
remove.
9. Remove clips from back of front roof finisher, and then pull out
front roof finisher toward front of vehicle to remove it. (with sun-
roof model)
10. Pull out sunroof motor harness connector from front roof finisher
mounting hole to disconnect. (with sunroof model)
11. Pull out spot lamp (map lamp) toward lower side of vehicle and disconnect harness connector.
12. Disconnect harness connector for hands-free phone microphone. (Only for models with Car wings unit)
13. Pull spot lamp holder assembly toward vehicle lower, and disen-
gage dual-lock fastener and metal clips.
SIIA0224J
PIIA9621E
PIIA9622E
PIIA6272E

HEADLINING
EI-57
C
D
E
F
G
H
J
K
L
MA
B
EI

14. Push headlining toward rear of vehicle after removing, Pull out
clip holder of headlining rear end from clips and remove roof
hook on front of sunroof opening at the same time.
15. Remove front end of headlining right side from front door LH
opening so as to avoid center console finisher upper surface
after pulling out.
CAUTION:

When removing, 2 workers are required. (1 for each front
and rear of headlining)

Cover center console finisher upper surface with a shop
cloth so as to prevent it from being damaged.

Set A/T selector lever to D position, and make a space to
remove front end of headlining right side.

Do not bend headlining when removing.
16. Remove the following parts after removing headlining.

Personal lamp (LH/RH)

Roof harness assembly

Spot lamp holder assembly

Headlining rear end clip (removing on roof rail)
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Install headlining assembly after inserting clips to clip holder of headlining rear end.
PIIA7119E
PIIA7120E

EM-56
[QR]
TIMING CHAIN

a. Loosen mounting bolts in reverse order as shown in the figure,
and remove RH engine mounting bracket.
b . U s e s e a l c u t t e r [ S S T: K V 1 0 1111 0 0 ] o r e q u i v a l e n t t o o l t o c u t l i q -
uid gasket for removing front cover.
CAUTION:
Be careful not to damage the mating surfaces.
c. Pull out downward front cover.
CAUTION:
Do not let A/C and power steering pipings interfere with
upper part of front cover.
14. Remove front oil seal from front cover using suitable tool.
CAUTION:
Be careful not to damage front cover.
15. Remove timing chain with the following procedure:
a. Push in chain tensioner plunger. Insert a stopper pin into hole on
chain tensioner body to secure chain tensioner plunger and
remove chain tensioner.
NOTE:
Use approximately 0.5 mm (0.02 in) dia. hard metal pin as a
stopper pin.
b. Remove timing chain.
CAUTION:
Do not rotate crankshaft or camshaft while timing chain is removed. It causes interference
between valve and piston.
16. Remove camshaft sprockets. Refer to EM-41, "
CAMSHAFT" .
17. Remove timing chain slack guide, timing chain tension guide and oil pump drive spacer.
18. Remove balancer unit timing chain tensioner with the following procedure:
a. Lift lever up, and release ratchet claw for return proof.
b. Push tensioner sleeve in, and hold it.
c. Matching the hole on lever with the one on body, insert a stopper
pin to secure tensioner sleeve.
NOTE:
Use approximately 1 mm (0.04 in) dia. hard metal pin as a stop-
per pin.
d. Remove balancer unit timing chain tensioner.
KBIA0083E
KBIA0048E
KBIA0121E

FUEL SYSTEM
FL-3
C
D
E
F
G
H
I
J
K
L
MA
FL

FUEL SYSTEMPFP:17503
Checking Fuel LinesBBS005AE
Inspect fuel lines, fuel filler cap and fuel tank for improper attach-
ment, leaks, cracks, damage, loose connections, chafing or deterio-
ration.
If necessary, repair or replace damaged parts.
General PrecautionsBBS005AF
WARNING:
When replacing fuel line parts, be sure to observe the following.

Put a “CAUTION: FLAMMABLE” sign in the workshop.

Be sure to work in a well ventilated area and furnish workshop with a CO2 fire extinguisher.

Do not smoke while servicing fuel system. Keep open flames and sparks away from the work area.

Put drained fuel in an explosion-proof container and put the lid on securely. Keep the container in
safe area.
CAUTION:

Use gasoline required by the regulations for octane number. Refer to GI-6, "Precautions for Fuel" .

Before removing fuel line parts, perform the following procedures:
–Release fuel pressure from the fuel lines. Refer to EC-49, "FUEL PRESSURE RELEASE"
(QR20DE), or EC-392, "FUEL PRESSURE RELEASE" (VQ23DE and VQ35DE).
–Disconnect the battery cable from negative terminal.

Always replace clamps with new ones.

Do not kink or twist tubes when they are being installed.

Perform work on level place.

Do not tighten hose clamps excessively to avoid damaging hoses.

After connecting fuel tube quick connectors, make sure
quick connectors are secure.
Ensure that connector and resin tube do not contact any
adjacent parts.

After installing tubes, make sure there is no fuel leakage at
connections in the following steps.
–Apply fuel pressure to fuel lines with turning ignition switch
“ON” (with engine stopped). Then check for fuel leaks at
connections.
–Start engine and rev it up and check for fuel leaks at con-
nections.

Use only a genuine NISSAN fuel filler cap as a replacement.
If an incorrect fuel filler cap is used, the “MIL” may come
on.

For servicing “Evaporative Emission System” parts, refer to
EC-27, "
EVAPORATIVE EMISSION SYSTEM" (QR20DE), or
EC-366, "
EVAPORATIVE EMISSION SYSTEM" (VQ23DE
and VQ35DE).
SMA803A
SBIA0504E