2003 NISSAN TEANA key

CVT-8
PRECAUTIONS

PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BCS001NA
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions Necessary for Steering Wheel Rotation After Battery DisconnectBCS001NB
NOTE:

This Procedure is applied only to models with Intelligent Key system and NVIS/IVIS (NISSAN/INFINITI
VEHICLE IMMOBILIZER SYSTEM - NATS).

Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″LOCK″ position.

Always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NVIS/IVIS, an electrically controlled steering lock
mechanism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-II.

TROUBLE DIAGNOSIS
CVT-27
D
E
F
G
H
I
J
K
L
MA
B
CVT

DIAGNOSTIC WORKSHEET
Information from Customer
KEY POINTS

WHAT..... Vehicle & CVT model

WHEN..... Date, Frequencies

WHERE..... Road conditions

HOW..... Operating conditions, Symptoms
Diagnostic Worksheet Chart
Customer name MR/MS Model & Year VIN
Trans. Model Engine Mileage
Malfunction Date Manuf. Date In Service Date
Frequency❏ Continuous❏ Intermittent ( times a day)
Symptoms❏ Vehicle does not move. (❏ Any position❏ Particular position)
❏ No shift
❏ Lock-up malfunction
❏ Shift shock or slip (❏ N → D❏ N → R❏ Lock-up❏ Any drive position)
❏ Noise or vibration
❏ No pattern select
❏ Others
()
1❏ Read the item on cautions concerning fail-safe and understand the customer's complaintCVT-24
2❏ CVT fluid inspection
CVT-32❏ Leak (Repair leak location.)
❏ Sta te
❏ Amount
3❏ Stall test and line pressure test
CVT-32
,
CVT-33
❏ Sta ll tes t
❏ Torque converter one-way clutch
❏ Reverse brake
❏ Forward clutch
❏ Steel belt❏ Engine
❏ Line pressure low
❏ Primary pulley
❏ Secondary pulley
❏ Line pressure inspection - Suspected part:

CVT-180
CVT SHIFT LOCK SYSTEM

CVT SHIFT LOCK SYSTEMPFP:00000
DescriptionBCS001MP

The electrical key interlock mechanism also operates as a shift lock:
With the ignition switch turned to ON, the selector lever cannot be shifted from “P” (parking) to any other
position unless the brake pedal is depressed.
With the key removed, the selector lever cannot be shifted from “P” to any other position.
The key cannot be removed unless the selector lever is placed in “P”.

The shift lock and key interlock mechanisms are controlled by the ON-OFF operation of the shift lock sole-
noid and by the operation of the rotator and slider located inside the key cylinder, respectively.
Shift Lock System Electrical Parts LocationBCS001MQ
NOTE:
This emergency lever can be used when battery is off ignition key cannot be removed. In the situation like this,
by operating this lever, ignition key can be removed.
1. Stop lamp switch 2. Shift lock control unit
A. Behind Audio Unit B. Key lock solenoid C. Emergency lever
D. Key switch E. Shift lock release button F. Detention switch (shift)
G. Detention switch (key) H. Shift lock solenoid
SCIA7845E

CVT SHIFT LOCK SYSTEM
CVT-183
D
E
F
G
H
I
J
K
L
MA
B
CVT

Shift Lock Control Unit Reference ValuesBCS001MT
SHIFT LOCK HARNESS CONNECTOR TERMINALS LAYOUT
SHIFT LOCK CONTROL UNIT INSPECTION TABLE
Shift lock control unit terminal data are reference values, measured between each terminal and ground.
NOTE:
Take care that the pointer of circuit tester swings only momentarily because the output time is so short. If the inspection is done with an
oscilloscope, it should be observed that the power source voltage lasts for 3.5 to 10 ms.
SCIA2004E
Terminal
(Wire color)Item Condition Judgement standard
1
(Y/R)Power source Always Battery voltage
2
(L)Detention switch (for
key)When selector lever is not in “P” position with key
inserted or ignition knob switch pushed.Battery voltage
When selector lever is in “P” position with key
inserted.Approx. 0 V
3
(R)Detention switch (for
shift)When selector lever is not in “P” position. Battery voltage
When selector lever is in “P” position. Approx. 0 V
4
(R/G)Stop lamp switchWhen brake pedal is depressed Battery voltage
When brake pedal is released Approx. 0 V
5
(V/W)Vehicle speed signal
(8pulse signal)Speed meter is operatedRefer to DI-13, "
Terminals and Refer-
ence Value for Unified Meter and A/C
Amp." .
6
(G)Ignition signalIgnition switch: except ON Approx. 0 V
Ignition switch: ON Battery voltage
7
(R/W)Shift lock solenoid

When selector lever is in “P” position, brake
pedal is depressed, and ignition switch is ON.

When selector lever is not in “P” position, igni-
tion switch is ON, and vehicle speed is 10 km/h
(6 MPH) or less.

Within 3 minutes, after ignition switch turning to
other position from ON position, while selector
lever is not in “P” position and vehicle speed is
10 km/h (6 MPH) or less.Approx. 0 V
Except the above Battery voltage
8
(B)Ground — Approx. 0 V
9
(G/B)Key lock solenoidWhen selector lever is not “P” position.Battery voltage for approx. 0.1 sec.
(Note)
When selector lever is in “P” position. Approx. 0 V
10
(G/W)Key unlock solenoidWhen selector lever is in “P” position with ignition
switch in except ON position.Battery voltage for approx. 0.1 sec.
(Note)
Except the above. Approx. 0 V

CVT-184
CVT SHIFT LOCK SYSTEM

Component InspectionBCS001MU
SHIFT LOCK SOLENOID
Check operation by applying battery voltage to the CVT device har-
ness connector.
CAUTION:
Be sure to apply the voltage of the correct polarity to the
respective terminals. Otherwise, the part may be damaged.
DETENTION SWITCH (FOR KEY)
Check continuity between terminals of the CVT device harness con-
nector.
DETENTION SWITCH (FOR SHIFT)
Check continuity between terminals of the CVT device harness con-
nector.
KEY LOCK SOLENOID
Key Lock
Check operation by applying battery voltage to ignition knob switch,
key switch and key lock solenoid harness connector terminal.
CAUTION:
Be careful not to cause burnout of the harness.
Connector Terminal
M92 9 (Battery voltage) - 10 (Ground)
SCIA2005E
Condition Connector Terminal Continuity
When selector lever is in “P”
position.
M92 5 - 6No
When selector lever is not in
“P” position.Ye s
SCIA2006E
Condition Connector Terminal Continuity
When selector lever is in “P”
position.
M92 13 - 14No
When selector lever is not in
“P” position.Ye s
SCIA2046E
Connector Terminal
M20 6 (Battery voltage) - 5 (Ground)
SCIA6645E

CVT SHIFT LOCK SYSTEM
CVT-185
D
E
F
G
H
I
J
K
L
MA
B
CVT

Key Unlock
Check operation by applying battery voltage to ignition knob switch,
key switch and key lock solenoid harness connector terminal.
CAUTION:
Be careful not to cause burnout of the harness.
IGNITION KNOB SWITCH
Check continuity between terminals of ignition knob switch, key
switch and key lock solenoid harness connector.
STOP LAMP SWITCH
Check continuity between terminals of the stop lamp switch harness
connector.
Check stop lamp switch after adjusting brake pedal. Refer to BR-6,
"Inspection and Adjustment" .
Connector Terminal
M20 5 (Battery voltage) - 6 (Ground)
SCIA6647E
Condition Connector Terminal Continuity
Pushed
M20 2 - 7Ye s
Released No
SCIA7773E
Condition Connector Terminal Continuity
When brake pedal is depressed
E210 3 - 4Ye s
When brake pedal is released No
SCIA2126E

DI-2 Wiring Diagram — CVTIND — ............................... 52
CVT Indicator Is Malfunction .................................. 54
WARNING CHIME ..................................................... 56
System Description ................................................. 56
POWER SUPPLY AND GROUND CIRCUIT ....... 56
IGNITION KEY WARNING CHIME (WITHOUT
INTELLIGENT KEY) ............................................ 56
IGNITION KEY WARNING CHIME (WITH INTEL-
LIGENT KEY) ...................................................... 57
LIGHT WARNING CHIME ................................... 57
Component Parts and Harness Connector Location ... 58
Schematic ............................................................... 59
Wiring Diagram — CHIME — ................................. 60
Terminals and Reference Value for BCM ................ 63
Terminals and Reference Value for Unified Meter
and A/C Amp. ......................................................... 64
Terminals and Reference Value for Combination
Meter ...................................................................... 65
CONSULT-II Function ............................................. 65
DIAGNOSTIC ITEMS DESCRIPTION ................. 65
CONSULT-II BASIC OPERATION PROCEDURE ... 65
DATA MONITOR .................................................. 65
ACTIVE TEST ...................................................... 66
Trouble Diagnosis ................................................... 66
HOW TO PROCEED WITH TROUBLE DIAGNO-
SIS ....................................................................... 66
PRELIMINARY CHECK ....................................... 66
Key Warning Chime and Light Warning Chime Does
Not Operated .......................................................... 67
Key Warning Chime Does Not Operate (Without
Intelligent Key) ........................................................ 69
Key Warning Chime Does Not Operate (With Intel-
ligent Key, When Mechanical Key Is Used) ............ 71
Key Warning Chime Does Not Operate (With Intel-
ligent Key, When Intelligent Key Is Carried With The
Driver) ..................................................................... 73
Light Warning Chime Does Not Operate ................. 75
CAN COMMUNICATION ........................................... 76
System Description ................................................. 76
CAN Communication Unit ....................................... 76

COMBINATION METERS
DI-5
C
D
E
F
G
H
I
J
L
MA
B
DI

FA I L - S A F E
Solution When Communication Error Between the Unified Meter and A/C Amp. and the Com-
bination Meter
Function Specifications
SpeedometerReturn to zero when discontinuing communication or receiv-
ing irregular data.
Tachometer
Reset to zero by suspending communication.
Fuel gauge
Illumination control Combination meter illumination When suspending communication, change to nighttime mode.
Odo/trip meter Integrate in response to 8-pulse input.
Shift indicator The display turns off by suspending communication.
Warning buzzer The warning buzzer turns off by suspending communication.
Warning lamp/indicator lampLow water temperature indicator lamp
The lamp turns on by suspending communication. VDC OFF indicator (With VDC)
SLIP indicator (With VDC)
Brake warning lamp
ABS warning lamp
ASCD CRUISE indicator lamp
The lamp turns off by suspending communication. ASCD SET indicator lamp
Turn signal indicator lamp
High-beam indicator lamp
Front fog indicator lamp
Rear fog indicator lamp
Oil pressure warning lamp
Door warning lamp
High water temperature warning lamp
Malfunction indicator lamp
A/T CHECK warning lamp
CVT indicator lamp
KEY warning lamp
LOCK warning lamp