2003 DAEWOO MATIZ window

9B – 2 LIGHTING SYSTEMS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
HEADLAMPS AND PARKING LAMPS
The headlamps are controlled by the multifunction lever
located on the left side of the steering column. They will
come on with the ignition switch in any position. Turning
the headlamp switch to the first position turns on the
parking lamps, the license plate lamps and the instru-
ment panel illumination. Turning the switch to the sec-
ond position turns on all of the previous lamps and the
headlamps. Turning the switch to the off position turns
off all the lamps.
The parking lamps can be turned on by turning the light-
ing switch to the first position. The parking lamps can be
turned off by turning the switch to the OFF position.
Headlamp high beam and low beam are also controlled
by this lever. When the headlamps are on, pushing the
lever away from the driver until the switch clicks
changes the lamp from low beam to high beam. An indi-
cator lamp on the instrument cluster assembly will come
on when the high beam headlamps are on. To return the
headlamps to low beam, pull the lever toward the driver.
The headlamps must be aimed for proper illumination of
the road. Headlamp aim should be checked whenever a
new headlamp assembly is installed or service repairs to
the front end area may have disturbed the headlamp as-
sembly or its mountings.
FRONT TURN SIGNAL LAMPS
When the turn signals are activated, the side turn signal
lamps flash to signal a turn. The turn signal works only
when the ignition switch is on.
The turn signals are controlled by the light switch on the
left side of the steering column. Moving the lever all the
way up or down (past the detent) will turn on the turn sig-
nals. When the turn is completed, the lever will return to
horizontal and the turn signals will stop flashing.
For changing lanes or shallow turns where the steering
wheel does not turn far enough to cancel the signal,
move the signal only to the first detent and hold it there.
When the lever is released, it will return to horizontal and
the turn signal will cancel.
REAR FOG LAMP
The rear fog lamp is incorporated in the drive side tail-
lamp assembly and are controlled by the rear fog lamp
switch on the instrument panel. The rear fog lamp can
be turned on only when headlamps are on.
TAILLAMPS
The taillamps, stoplamps, backup lamp(s), rear fog lamp
(if equipped with) and turn signal lamps are one assem-
bly.
Turning on either the headlamps or the parking lamps
will also turn on the taillamps. When the brake pedal is
pushed, the taillamps will glow brighter to serve as sto-
plamps.
The center high-mounted stoplamp is located in the rear
window and will come on when the brake pedal is
pressed.
LICENSE PLATE LAMPS
The license plate lamps will come on when the head-
lamps or the parking lamps are on. The license plate
lamps are mounted on the rear bumper, above the li-
cense plate.
INTERIOR COURTESY LAMP
The courtesy lamp is located on the headliner just be-
fore the front seats. The lamp switch has three posi-
tions. If the switch is in the center position, the lamp will
go on whenever a door is opened and go off when it is
closed. In the ON position, the lamp will stay on until it is
turned off. In the OFF position, the lamp will not come
on, even when a door is opened.
BACKUP LAMP(S)
The backup lamps are located in the rear combination
lamps. They will come on when the transaxle is shifted
into REVERSE. On a vehicle with a manual transaxle,
they are activated by a reverse switch which is part of
the transaxle.
DAYTIME RUNNING LAMPS (DRL)
(W/Europe Only)
The daytime running lamps (DRL) work in conjunction
with the exterior lamps system. When the ignition switch
is turned to the ”II” position with the light switch off, park-
ing, tail, license plate and instrument panel lights illumi-
nate. And, when the engine is started, the headlamps
(low beam) also come on.
They remain on until the ignition switch is turned off or
the light switch is turned on. They revert to normal op-
eration when the light switch is on.
The daytime running lamps (DRL) is optional.

9B–12 LIGHTING SYSTEMS
DAEWOO M-150 BL2
D209B102
CHMSL MOUNTING BRACKET
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the center high–mounted stoplamp
(CHMSL). Refer to “Center High–Mounted Stoplamp”
in this section.
3. Remove the rear window wiper motor assembly. Re-
fer to Section 9D, Wipers/Washer Systems.
4. Remove the CHMSL mounting bracket.

Remove the bolts (1).

Remove the CHMSL mounting bracket (2).
D209B103
Installation Procedure
1. Install the CHMSL mounting bracket with the bolts.
2. Install the rear window wiper motor assembly. Refer
to Section 9D, Wipers/Washer Systems.
3 .Install the CHMSL. Refer to “Center High–Mounted
Stoplamp” in this section.
4. Connect the negative battery cable.
D19D510A
LICENSE PLATE LAMPS
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the license plate lamp from the tailgate han-
dle.

Remove the screws (1).

Draw out the license plate lamp (2).

Remove the license plate lamp bulb (3).
D19D511A
3. Remove the rear window wiper motor assembly. Re-
fer to Section 9D, Wipers/Washer Systems.
4. Disconnect the electrical connector in the tailgate.
5. Remove the tailgate handle. Refer to Section 9M, Ex-
terior Trim.
6. Remove the license plate lamp socket.

Remove the socket (1).

LIGHTING SYSTEMS 9B–13
DAEWOO M-150 BL2
D19D512A
Installation Procedure
1. Install the license plate lamp socket.
2. Install the tailgate handle. Refer to Section 9M, Exte-
rior Trim.
3. Connect the electrical connector.
4. Remove the rear window wiper motor assembly. Re-
fer to Section 9D, Wipers/Washer Systems.
5. Install the license plate lamp bulb.
6. Install the license plate lamp with the screws.
7. Connect the negative battery cable.
D109D513
DOOR JAMB SWITCH
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the door jamb switch.

Remove the screw (1).

Disconnect the electrical connector (2).

Remove the door jamb switch (3).
D109D514
Installation Procedure
1. Install the door jamb switch with the screw.
2. Connect the electrical connector.
3. Connect the negative battery cable.
D19D515A
INTERIOR COURTESY LAMP
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the interior courtesy lamp.

Pry off the interior courtesy lamp lens (1).

Remove the screws (2).

Disconnect the electrical connector (3).

Remove the interior courtesy lamp (4).

DAEWOO M-150 BL2
SECTION 9D
WIPERS / WASHER SYSTEMS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9D-2. . . . . . . . . . . . . . . . . .
Windshield Wiper System 9D-2. . . . . . . . . . . . . . . . . .
Windshield Washer System 9D-2. . . . . . . . . . . . . . . . .
Rear Window Wiper/Washer System 9D-2. . . . . . . . .
Diagnostic Information and Procedures 9D-3. . . . .
Windshield/Rear Window Wiper and Washer
System 9D-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9D-6. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 9D-6. . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield Wiper Arm 9D-6. . . . . . . . . . . . . . . . . . . . .
Rear Window Wiper Arm 9D-6. . . . . . . . . . . . . . . . . . .
Windshield Wiper Motor 9D-7. . . . . . . . . . . . . . . . . . . .
Rear Window Wiper Motor 9D-8. . . . . . . . . . . . . . . . . . Windshield Wiper Linkage 9D-9. . . . . . . . . . . . . . . . . .
Windshield Wiper Blade 9D-10. . . . . . . . . . . . . . . . . . .
Washer Reservoir 9D-10. . . . . . . . . . . . . . . . . . . . . . . .
Washer Pump 9D-11. . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield Washer Nozzle 9D-12. . . . . . . . . . . . . . . .
Rear Window Washer Nozzle 9D-12. . . . . . . . . . . . . .
Washer Hose 9D-13. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 9D-15. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 9D-15. . . . . . . . . .
Schematic and Routing Diagrams 9D-16. . . . . . . . . .
Windshield/Rear Window Wiper/Washer
System 9D-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

WIPERS/WASHER SYSTEMS 9D–3
DAEWOO M-150 BL2
DIAGNOSTIC INFORMATION AND PROCEDURES
WINDSHIELD/REAR WINDOW WIPER AND WASHER SYSTEM
ConditionProbable CauseCorrection
Windshield Wipers Do Not
Work At Any Speed
The open or a short in the power
supply circuit to the fuse F8.
Repair or replace the open a short
in the power supply circuit to the
fuse F8.

Fuse F8 is blown.
Replace the fuse F8.

Faulty wiper/washer switch.
Replace the wiper/washer switch.

The circuit between the
wiper/washer switch connector
and the wiper relay is open or
short.
Repair or Replace the wiring
harness.

The circuit between the fuse F8
and the wiper relay is open or
short.
Repair or Replace the wiring
harness.

Faulty wiper relay.
Replace the wiper relay.

The circuit between the wiper
relay and the ground G201 is the
open circuit or a short circuit.
Repair or Replace the open circuit
or a short circuit between the
wiper relay and the ground G201.

The circuit between the
wiper/washer switch and the wiper
motor is the open circuit or a short
circuit.
Repair or Replace the wiring
harness.

The circuit between the fuse F8
and the wiper motor is the open
circuit or a short circuit.
Repair or Replace the wiring
harness.

The circuit between the wiper
relay and the wiper motor is the
open circuit or a short circuit.
Repair or Replace the wiring
harness.

Faulty wiper motor.
Replace the wiper motor.

The connection of the wiper
linkage and the wiper motor is
poor.
Tighten completely the nut.

Tighten completely the ball.

Wiper linkage is out of order.
Replace the wiper linkage.
Wipers Do Not Work On High
Faulty wiper/washer switch.
Replace the wiper/washer switch.
Speed, Low Speed OK
The circuit between the
wiper/washer switch and the wiper
motor is the open circuit or a short
circuit.
Repair or Replace the wiring
harness.

Faulty wiper motor.
Replace the wiper motor.
Wipers Do Not Work On Low
Faulty wiper/washer switch.
Replace the wiper/washer switch.
Speed, High Speed OK
The circuit between the
wiper/washer switch and the wiper
motor is the open circuit or a short
circuit.
Repair or Replace the wiring
harness.

Faulty wiper motor.
Replace the wiper motor.

9D –4 WIPERS/WASHER SYSTEMS
DAEWOO M-150 BL2
WINDSHIELD/REAR WINDOW WIPER AND WASHER SYSTEM(Cont’d)
ConditionProbable CauseCorrection
Wipers Do Not On Intermittent,
Other Speed OK
The circuit between the fuse F8
and the wiper relay is the open
circuit or a short circuit.
Repair or Replace the wiring
harness.

The circuit between the fuse F8
and the wiper motor is the open
circuit or a short circuit.
Repair or Replace the wiring
harness.

Faulty wiper/washer switch.
Replace the wiper/washer switch.

The circuit between the
wiper/washer switch and the wiper
relay is the open circuit or a short
circuit.
Repair or Replace the wiring
harness.

Faulty wiper relay.
Replace the wiper relay.

The circuit between the wiper
relay and the wiper motor is the
open circuit or a short circuit.
Repair or Replace the wiring
harness.

Poor ground G201.
Repair or Replace the wiring
harness.

Faulty wiper motor.
Replace the wiper motor.
Windshield Washer Does Not
Work, Windshield Wipers OK
The open or a short in the power
supply circuit to the fuse F9.
Repair or Replace the open or a
short in the power supply circuit to
the fuse F9.

Fuse F9 is blown.
Replace the fuse.

The circuit between the fuse F9
and the wiper/washer switch is the
open circuit or a short circuit.
Repair or Replace the wiring
harness.

Faulty wiper/washer switch.
Replace the wiper/washer switch.

The circuit between the wiper/
washer switch and the wiper relay
is the open circuit or a short
circuit.
Repair or Replace the wiring
harness.

Faulty wiper relay.
Replace the wiper relay.

The circuit between the wiper
relay and ground G201 is the
open circuit or a short circuit.
Repair or Replace the wiring
harness.

The circuit between the
wiper/washer switch and the
windshield washer pump is the
open circuit or a short circuit.
Repair or Replace the wiring
harness.

Faulty windshield washer pump.
Replace the windshield wash
pump.

Poor ground G201.
Repair or Replace the wiring
harness.

WIPERS/WASHER SYSTEMS 9D–5
DAEWOO M-150 BL2
WINDSHIELD/REAR WINDOW WIPER AND WASHER SYSTEM(Cont’d)
ConditionProbable CauseCorrection
Rear Wiper Does Not Work
The open or a short in the power
supply circuit to the fuse F9.
Repair or Replace the open or a
short in the power supply circuit to
the fuse F8.

Fuse F9 is blown.
Replace the fuse F9.

The circuit between the fuse F9
and the wiper/washer switch is the
open circuit or a short circuit.
Repair or Replace the wiring
harness.

Faulty wiper/washer switch.
Replace the wiper/washer switch.

The circuit between the
wiper/washer switch and the rear
window wiper motor is the open
circuit or a short circuit.
Repair or Replace the wiring
harness.

The circuit between the fuse F9
and the rear window wiper motor
is the open circuit or a short
circuit.
Repair or Replace the wiring
harness.

Faulty rear window wiper motor.
Replace the rear window wiper
motor.

Poor ground G403.
Repair or Replace the wiring
harness.
Rear Window Washer Does Not
Work, Rear Window Wiper OK
The open or a short in the power
supply circuit to the fuse F9.
Repair or Replace the open or a
short in the power supply circuit to
the fuse F9.

Fuse F9 is blown.
Replace the fuse F9.

The circuit between the fuse F9
and wiper/washer switch is the
open circuit or a short circuit.
Repair or Replace the wiring
harness.

Faulty wiper/washer switch.
Replace the wiper/washer switch.

The circuit between the
wiper/washer switch and the
windshield washer pump is the
open circuit or a short circuit.
Repair or replace the wiring
harness.

Faulty windshield washer pump.
Replace the windshield washer
pump.

Poor ground G102.
Repair or Replace the wiring
harness.

9D –6 WIPERS/WASHER SYSTEMS
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON–VEHICLE SERVICE
D109D519
WINDSHIELD WIPER ARM
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the wiper arm.

Remove the cap (1).

Remove the nut (2).

Remove the wiper arm (3).
D109D520
Installation Procedure
1. Install the wiper arm with the nut.
2. Install the cap.
D109D521
REAR WINDOW WIPER ARM
Removal Procedure
1. Remove the washer nozzle from the wiper arm. Refer
to “Rear Washer Nozzle” in this section.
2. Remove the wiper blade. Refer to “Windshield Wiper
Blade” in this section.
3. Remove the wiper arm.

Remove the cap (1).

Remove the nut (2).

Remove the wiper arm (3).