ENGINE CONTROLS 1F–139
DAEWOO M-150 BL2
DIAGNOSTIC TROUBLE CODE (DTC) – P0300 MULTIPLE CYLINDER MISFIRE
System Description
The Engine Control Module (ECM) monitors the crank-
shaft and camshaft positions to detect if the engine is
misfiring. The ECM looks for a quick drop in crankshaft
speed. This test is executed in blocks of 100 engine rev-
olution tests. It may take between one to several tests to
store a Diagnostic Trouble Code (DTC) and illuminate
the Malfunction Indicator Lamp (MIL). Under light misfire
conditions, it may also take more than one trip to set a
DTC. Severe misfire will flash the MIL, indicating that
catalyst damage is possible.
Conditions for Setting the DTC
Emission threshold is 3.0% for automatic transaxle
and 3.0% for manual transaxle.
20 engine cycles have occurred since cranking has
started.
A/C compressor clutch has not just engaged or disen-
gaged.
Engine load and engine speed are in a detectable re-
gion and are at or above zero torque.
Camshaft Position (CMP) sensor is in synchroniza-
tion.
Electric Exhaust Gas Recirculation (EEGR) flow
diagnostic is not in progress.
Fuel level is greater than or equal to 20% of rated
tank capacity.
Decel Fuel Cutoff (DFCO) not active.
Fuel is not shutoff from high engine speed of 6500
rpm for manual transaxle vehicle or 6500 rpm in drive
and 6250 rpm in park for automatic transaxle ve-
hicles.
Fuel is not shutoff at 255 km/h (158 mph).
An automatic transmission is not shifting.
Throttle position change is less than 3% per 125 ms.
Vehicle has not encountered an abusive engine
speed of 7000 rpm.
Crankshaft speed patters are normal.Throttle position is less than 4% when vehicle speed
is greater than 10 km/h (6 mph).
Engine speed is between 600 and 4500 rpm.
Vehicle voltage is between 11 and 16 volts.
Engine Coolant Temperature (ECT) is between –7°C
(20°F) and 120°C (248°F).
The engine speed is less than or equal to 1800 rpm or
the crank angle sensing error has not been learned.
There is the correct ratio between Crankshaft Posi-
tion (CKP) sensor pulses and CMP sensor pulses.
DTCs P0106, P0107, P0108, P0117, P0118, P0122,
P0123, P0320, P0337, P0341, P0342 and P0502 are
not set.
Action Taken when the DTC Sets
Emission related.
“Armed” after two trip with a fail.
“Disarmed” after one trip with a pass.
MIL on if failure is detected in three consecutive trips.
Stores a History DTC on the third consecutive with a
fail (The DTC will be armed after the second fail).
Stores a Freeze Frame on the third consecutive trip
with a fail (if empty).
Conditions for Clearing the MIL/DTC
The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
A history DTC will clear after 40 consecutive warm up
cycles without a fault.
DTC(s) can be cleared by using the scan tool.
Disconnecting the ECM battery feed for 10 seconds.
Diagnostic Aids
An intermittent can also be the result of a defective re-
luctor wheel. Remove the CKP sensor and inspect the
reluctor wheel through the sensor mount hole. Check for
porosity and the condition of wheel. If the DTC is inter-
mittent refer to “Symptoms Diagnosis” in this section.
DTC P0300 – Multiple Cylinder Misfire
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Was the check performed?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON, with the engine OFF.
3. Request Diagnostic Trouble Codes (DTCs)
Are DTCs P0201, P0202, P0203, P0204 set?
–Go to
Applicable DTC
table
Go to Step 3
5B – 2 FIVE-SPEED MANUAL TRANSAXLE
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
FIVE-SPEED MANUAL TRANSAXLE
This five-speed transaxle assembly adopts the synchro-
nized mesh type of 5 forward speed. The reverse speed
gear is driven by sliding idle gear without synchronizer.
REVERSE GEAR MISSHIFT
PREVENTING MECHANISM
It prevents the gear from directly being shifted from 5th
to reverse when shifting to reverse from 5th. Shift to the
reverse in neutral position to prevent the shift cam from
being interfered to the shift guide bolt.
D103B001
In case of shifting to 5th gear, shift and select shaft ro-
tates to right that shift cam aparts from guide bolt and
moves upwards by returning spring. Therefore, shifting
to reverse in this condition is impossible because of in-
terference of guide bolt.
D103B002
When shifting to reverse from neutral position between
5th and reverse, shift cam rotates to left and shifting is
possible.
D103B003
DIFFERENTIAL
Differential is integrated with transmission case and
installed on chassis together with engine. It changes the
direction of power and increase torque by reducing
speed.
Reduction gear is installed parallel to counter shaft and
is helical gear type. Differential gear is bevel gear type
and is integrated with reduction gear.
