2003 DAEWOO MATIZ window

9P – 2 DOORS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
DOOR LOCK STRIKER
The front and the rear door lock strikers each consist of
a striker with two screws threaded into a floating cage
plate in the B-pillars and C-pillars. The door is secured in
the closed position when the door lock fork snaps over
and engages the striker.
CHILDPROOF REAR DOOR LOCK
The childproof rear door locks help prevent passengers,
especially children, from opening the rear doors of the
vehicle from the inside.
In order to activate these locks, move the levers of both
rear doors to the lock position. Then, close both doors.
Rear passengers will be unable to open the doors from
the inside of the vehicle.
In order to deactivate the childproof rear door lock, un-
lock the door from the inside of the vehicle and open the
door from the outside. Move the lever to the unlock posi-
tion. The rear door will now work normally.
POWER DOOR LOCKS
The power door locks use a solenoid that is contained in
each door lock assembly. The door locks are activatedby the actuator on the inside door handle or by the lock
cylinder on the driver door only. When the driver door is
locked or unlocked by the actuator or lock cylinder, all
doors are locked or unlocked accordingly.
POWER WINDOWS
The power windows are controlled by electrical switches
on the front door tirm and operated by a motor at each
window regulator. The windows are lowered by pressing
the switch and raised by pulling up on the switch. The
window will stop movement when the switch is released
or when the window is completely open or closed.
TAILGATE STRUT
This vehicle is equipped with the gas struts. The struts
support the tailgate suitably when opening the tailgate.
The strut contained the high pressure compressed gas.
Therefore, be careful not to take apart, puncture, apply
heat or fire bacause the strut may explode.

9P –4 DOORS
DAEWOO M-150 BL2
1. Seal Trim
2. Lock Button
3. Trim Panel
4. Pocket Handle (Deluxe Type)
5. Pocket Handle Bracket (Deluxe Type)
6. Inside handle
7. Manual Regulator Handle
8. Pocket Handle (Standard Type)
9. Door Speaker Cover
10. Map Pocket
11. Contact Switch
12. Striker
13. Opening Weatherstrip
14. Door Weatherstrip
15. Glass Run
16. Front Door
17. Inside Channel Weatherstrip
18. Inside Handle Rod
19. Door Lock20. Door Lock Cylinder Rod
21. Lock Rod
22. Actuator Rod
23. Actuator
24. Window Regulator
25. Outside Channel Weatherstrip
26. Outside Handle Rod
27. Outside Handle
28. Division Bar
29. Quarter Glass
30. Quarter Glass Run
31. Door Hinge
32. Door Hold Open Link
33. Power Window Switch Cover
34. Mirror Switch
35. Power Window Switch Assembly
36. Mirror switch Blank
37. Door Side Molding

9P –6 DOORS
DAEWOO M-150 BL2
1. Seal Trim
2. Lock Button
3. Trim Panel
4. Pocket Handle (Deluxe Type)
5. Pocket Handle Bracket (Deluxe Type)
6. Inside handle
7. Manual Regulator Handle
8. Pocket Handle (Standard Type)
9. Striker
10. Opening Weatherstrip
11. Door Weatherstrip
12. Glass Run
13. Interior Garnish Molding
14. Rear Door
15. Inside Channel Weatherstrip16. Upper Guide Rail
17. Exterior Garnish Molding
18. Lower Guide Rail
19. Lock Rod
20. Door Lock
21. Inside Handle Rod
22. Actuator Rod
23. Actuator
24. Outside Handle Rod
25. Outside Handle
26. Window Regulator
27. Outside Channel Weatherstrip
28. Door Hinge
29. Door Hold Open Link
30. Door Side Molding

DOORS 9P–19
DAEWOO M-150 BL2
D109C600
Installation Procedure
1. Install the door lock cylinder with the clip.
2. Install the outside door handle. Refer to “Outside
Front Door Handle” in this section.
3. Connect the negative battery cable.
D109C601
MANUAL WINDOW REGULATOR
Removal Procedure
1. Remove the glass. Refer to Section 9L, Glass and
Mirrors.
2. Remove the window regulator.

Remove the screws (1).

Remove the regulator (2).
D109C602
Installation Procedure
1. Install the regulator with the screws.
2. Install the glass. Refer to Section 9L, Glass and Mir-
rors.
D109C603
POWER FRONT WINDOW
REGULATOR
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the glass. Refer to Section 9L, Glass and
Mirrors.
3. Remove the window regulator assembly.

Disconnect the window motor electrical connector
(1).

Remove the screws (2).

Remove the window regulator assembly (3).

9P –20 DOORS
DAEWOO M-150 BL2
D109C604
4. Remove the window motor from the window regula-
tor.

Remove the screws (1).

Remove the window regulator (2).
Caution: Be careful what you are doing when sepa-
rating the window motor and the window regulator.
You may be hurt.
D109C605
Installation Procedure
1. Install the window motor to the window regulator with
the screws.
2. Install the window regulator assembly with the screws.
3. Connect the window motor electrical connector.
4. Install the glass. Refer to Section 9L, Glass and Mir-
rors.
5. Connect the negative battery cable.
D109C606
FRONT DOOR ASSEMBLY
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the electrical connector under the instru-
ment panel.
Important: In case of the front passenger door, remove
the glove box in advance.
D109C607
3. Remove the fender. Refer to Section 9R, Body Front
End.
4. Remove the front door assembly.

Remove the door hinge bolts (1).

Remove the door hold open bolt (2).

Disconnect the body–to–door rubber grommet (3).

Remove the front door assembly (4).

DOORS 9P–23
DAEWOO M-150 BL2
D19C614A
Installation Procedure
Notice: Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use the correct
fastener to prevent premature corrosion.
1. Connect the body–to–tailgate rubber grommet.
2. With the aid of another technician, lightly secure the
tailgate with the bolts.
3. Adjust the tailgate for proper fit.
4. Install the tailgate strut. Refer to “Tailgate Strut” in this
section.
5. Connect the tailgate electrical connector.
6. Install the luggage compartment wheelhouse trim pan-
el. Refer to Section 9G, Interior Trim.
7. Connect the negative battery cable.
D209B113
TAILGATE LOCK CYLINDER
Removal Procedure
1. Disconnect the negative battery cable.
2. Open the tailgate.
3. Remove the rear window wiper motor assembly. Re-
fer to Section 9D, Wipers/Washer Systems.
4. Remove the tailgate lock cylinder.

Disconnect the tailgate lock rod (1).

Remove the nuts from the tailgate lock cylinder (2).

Remove the tailgate lock cylinder (3).
D209B114
Installation Procedure
1. Install the tailgate lock cylinder.
2. Install the rear window wiper motor assembly. Refer
to Section 9D, Wipers/Washer Systems.
3. Connect the negative battery cable.
D109C615
DOOR HINGE
Removal Procedure
1. With the aid of another technician, remove the door
hinge.

Remove the hinge–to–body bolts (1).

Remove the hinge–to–door bolts (2).

Remove the door hinge (3).

9P –28 DOORS
DAEWOO M-150 BL2
D109C631
Installation Procedure
1. Install the door opening weatherstrip to match the
marking.
2. Install the rocker panel trim and the lower B–pillar
panel trim.
D109E543
MANUAL WINDOW REGULATOR
HANDLE
Removal Procedure
1. Remove the window regulator handle.

Using a cloth, pull out the clip (1).

Remove the window regulator handle (2).
D109C632
Installation Procedure
1. Install the window regulator handle with the clip.
D19C634A
TAILGATE STRUT
Removal Procedure
1. Open the tailgate and suitably support it.
2. Remove the tailgate strut assembly.

Remove the end fitting nut from the ball studs (rear
body) (1).

Removethe end fitting nut from the ball studs (tail-
gate) (2).

9P –34 DOORS
DAEWOO M-150 BL2
POWER WINDOWS (FRONT ONLY)
D19C202B