2001 TOYOTA SEQUOIA wheel

F19140
Example:
A
BFront
F19139
Example:
Front
A
DI±840
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1034 Author: Date:
2005 SEQUOIA (RM1146U)
12 Interchange tires.
PREPARATION:
Interchange tire ºAº with a defective tire pressure monitor valve
sub±assy with tire ºBº with a normal one.
HINT:
If tire ºAº (left front ) is identified in step 11.
NEXT
13 Set tire pressure to normal value.
PREPARATION:
Set the tire pressure of all wheels to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT
14 Forcibly transmit transmitter ID.
PREPARATION:
Remove the valve core of tire ºAº, rapidly reduce the tire pres-
sure and forcibly transmit the transmitter ID of the tire pressure
monitor valve sub±assy.
NEXT

F19326
DATA LIST:
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±845
1039 Author: Date:
2005 SEQUOIA (RM1146U)
7 Registration of transmitter ID (See page DI±805).
PREPARATION:
(a) Confirm the transmitter ID on the DATA LIST.
(b) Register the transmitter ID for all wheels.
(c) Set the tire pressure to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT
8 Check DTC (See page DI±820).
CHECK:
Check for a DTC.
OK:
DTC is not output.
NG Go to step 9.
OK
End
9 Replace tire pressure monitor receiver assy (See page SA±13).
HINT:
Perform the inspection using parts from a normal vehicle when possible.
NEXT

± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±849
1043 Author: Date:
2005 SEQUOIA (RM1146U)
5 Check DTC (See page DI±820).
CHECK:
Check for a DTC.
OK:
DTC is not output.
HINT:

If the result is OK, replace the tire pressure monitor valve sub±assy specified in STEP 2.

Register the transmitter ID after replacement and then set the tire pressure to the specified value.
NG Go to step 11.
OK
Replace tire pressure monitor valve sub±
assy (See page SA±13).
6 Identify transmitter corresponding to DTC (See page DI±881).
NEXT
7 Adjust tire pressure to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT
8 Replace tire pressure monitor valve sub±assy (See page SA±16).
PREPARATION:
Replace the identified tire pressure monitor valve sub±assy with a new one.
HINT:
Before installing a new tire pressure monitor valve sub±assy onto the wheel, read and write down its trans-
mitter ID.
NEXT

F19326
DATA LIST:
DI±850
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1044 Author: Date:
2005 SEQUOIA (RM1146U)
9 Registration of transmitter ID (See page DI±805).
PREPARATION:
(a) Confirm the transmitter ID on the DATA LIST.
(b) Register the transmitter ID for all wheels.
(c) Set the tire pressure to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT
10 Check DTC (See page DI±820).
CHECK:
Check for a DTC.
OK:
DTC is not output.
NG Go to step 11.
OK
End
11 Replace tire pressure monitor receiver assy (See page SA±13).
HINT:
Perform the inspection using parts from a normal vehicle when possible.
NEXT

DI±864
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1058 Author: Date:
2005 SEQUOIA (RM1146U)
8 Check tire pressure warning lamp.
HINT:
Check all tires, including the spare, one at a time in this order: FR, FL, RR RL, Spare.
PREPARATION:
(a) Turn the ignition switch to the ON position.
(b) Rapidly reduce the pressure of the tires to approximately 120 kPa (1.2 kgf/cm
2, 35 psi).
(c) Check that the tire pressure warning lamp comes on for 1 second while rapidly reducing the pressure
or immediately after reducing the pressure.
(d) Note the check results.
(e) Set the tire pressure to the specified value.
CHECK:
Check that the tire pressure warning lamp comes on when each of the wheels is inspected.
RESULT:
Does not come on (All wheels)A
Does not come on (Some wheels)B
Comes on (All wheels)C
B Replace tire pressure monitor receiver assy
(See page SA±13).
HINT:
Replace the tire pressure monitor valve sub±assy for which the
tire pressure warning lamp did not come on during inspection.
C Perform initialization (See page DI±808).
A

F19138
Tire Pressure Monitor ECU:
SPD
GND
T17
9 to 14 V
0
Turn the wheel
DI±872
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1066 Author: Date:
2005 SEQUOIA (RM1146U)
NG Repair or replace harness or connector.
OK
3 Inspect tire pressure monitor ECU.
PREPARATION:
Remove the tire pressure monitor ECU with connectors still
connected.
CHECK:
Check voltage.
(1) Shift the shift lever to neutral.
(2) Jack up one of the front wheels.
(3) Turn the ignition switch to the ON position.
(4) Measure the voltage between terminals SPD and
GND of the tire pressure monitor ECU when the
front wheel is turned slowly.
OK:
Voltage is generated intermittently.
HINT:
As the vehicle speed (wheel revolution speed) increases, a
cycle of the waveform narrows.
NG Check combination meter assy (Speed signal
circuit) (See page SA±20).
OK
Replace tire pressure monitor ECU
(See page SA±20).

± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
DI±881
1075 Author: Date:
2005 SEQUOIA (RM1146U)
Identify transmitter (Error in present)
HINT:

Refer to IDENTIFY TRANSMITTER (ERROR IN PRESENT) if the DTC is output currently. Refer to
IDENTIFY TRANSMITTER (ERROR IN PAST) if a previously output DTC is not output now. Even when
DTCs C2165/65 to C2169/69 are output both as present and past codes, refer to IDENTIFY TRANS-
MITTER (ERROR IN PAST).

DTCs relevant to the transmitters are corresponding to each transmitter ID. It is impossible to identify
which tire is malfunctioning according to each transmitter ID. Therefore the following procedures must
be followed to confirm the ID No. and tire location.
INSPECTION PROCEDURE
1 Set the pressure of all tires to the specified value.
Tire sizeFrontRearSpare
P245 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)240 kPa (2.4 kgf/cm2, 35 psi)240 kPa (2.4 kgf/cm2, 35 psi)
P265 / 70 R 16220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
P265 / 65 R 17220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)220 kPa (2.2 kgf/cm2, 32 psi)
NEXT
2 Rapidly reduce the pressure of front right wheel to 120 kPa (1.2 kgf/cm2, 17 psi).
NEXT
DIDKI±01

DI±882
± DIAGNOSTICSTIRE PRESSURE WARNING SYSTEM
1076 Author: Date:
2005 SEQUOIA (RM1146U)
3 Using hand±held tester, check the tire pressure data of each wheel.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position, and push the hand±held tester main switch ON.
(c) Select the item below in the DATA LIST, and read its value displayed on the hand±held tester.
TIRE PRESSURE:
ItemMeasurement item/
Range (Display)Normal ConditionDiagnostic Note
TIREPRESS1
ID1 tire inflation pressure/
min.: 0 kPa (0 kgfVcm2, 0 psi),
max.: 637.5 kPa (6.48 kgfVcm2,
92.2 psi)Actual tire inflation pressure±
TIREPRESS2
ID2 tire inflation pressure/
min.: 0 kPa (0 kgfVcm2, 0 psi),
max.: 637.5 kPa (6.48 kgfVcm2,
92.2 psi)Actual tire inflation pressure±
TIREPRESS3
ID3 tire inflation pressure/
min.: 0 kPa (0 kgfVcm2, 0 psi),
max.: 637.5 kPa (6.48 kgfVcm2,
92.2 psi)Actual tire inflation pressure±
TIREPRESS4
ID4 tire inflation pressure/
min.: 0 kPa (0 kgfVcm2, 0 psi),
max.: 637.5 kPa (6.48 kgfVcm2,
92.2 psi)Actual tire inflation pressure±
TIREPRESS5
ID5 tire inflation pressure/
min.: 0 kPa (0 kgfVcm2, 0 psi),
max.: 637.5 kPa (6.48 kgfVcm2,
92.2 psi)Actual tire inflation pressure±
CHECK:
Check the tire pressure data of each tire.
NEXT
4 Is any of the tire pressure data 120 kPa (1.2 kgf/cm2, 17 psi)?
No The detected DTC is for the front right wheel
transmitter.
Ye s
5 Rapidly reduce the pressure of front left wheel to 120 kPa (1.2 kgf/cm2, 17 psi).
NEXT