2001 TOYOTA SEQUOIA ECO mode

DI±1350
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1544 Author: Date:
2005 SEQUOIA (RM1146U)
DTC B1796 Sleep Operation Failure Of Occupant
Classification ECU
CIRCUIT DESCRIPTION
During sleep mode, the occupant classification ECU reads the condition of each sensor while the ignition
switch is off.
In this mode, if occupant classification ECU detects an internal malfunction, DTC B1796 is output.
DTC No.DTC Detecting ConditionTrouble Area
B1796
Occupant classification ECU malfunction
Occupant classification ECU
HINT:
When DTC B1650/32 is detected as a result of troubleshooting for the supplemental restraint system, check
the DTCs stored in the occupant classification ECU. When DTC B1796 is output, perform troubleshooting
for the DTC.
INSPECTION PROCEDURE
1 Check DTC.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at least 10 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
HINT:
First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assembly.
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position.
(e) Using the hand±held tester, check the DTCs of the occupant classification ECU (see page DI±1147).
OK:
DTC B1796 is not output.
HINT:
Codes other than DTC B1796 may be output at this time, but they are not related to this check.
NG Go to step 2.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
DIDHH±01

H01003H23354
D Squib
Spiral
Cable
Airbag
Sensor
Assembly
C D
E F
DI±1362
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1556 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check steering wheel pad (D squib).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) From the step 11:
Disconnect the service wire from connector ºEº.
(d) Connect the connectors to the steering wheel pad.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1800, B1801, B1802 or B1803 is not output.
HINT:
Codes other than DTC B1800, B1801, B1802 and B1803 may
be output at this time, but they are not related to this check.
NG
Replace steering wheel pad
(see page RS±82).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).

H01024H23360
P Squib
Airbag
Sensor
Assembly
C D
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1383
1577 Author: Date:
2005 SEQUOIA (RM1146U)
10 Check front passenger airbag assembly (P squib).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) From the step 9:
Disconnect the SST from connector ºCº.
(d) Connect the connector to the front passenger airbag as-
sembly.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1805, B1806, B1807 or B1808 is not output.
HINT:
Codes other than DTC B1805, B1806, B1807 and B1808 may
be output at this time, but they are not related to this check.
NG Replace front passenger airbag assembly
(see page DI±1137).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).

H01003H23354
Spiral
CableAirbag
Sensor
Assembly D Squib
(Dual stage ±
2nd step)
C ED F
DI±1394
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1588 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check steering wheel pad (D squib, dual stage ± 2nd step).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) From the step 11:
Disconnect the service wire from connector ºEº.
(d) Connect the connectors to the steering wheel pad.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1810, B1811, B1812 or B1813 is not output.
HINT:
Codes other than DTC B1810, B1811, B1812 and B1813 may
be output at this time, but they are not related to this check.
NG
Replace steering wheel pad
(see page RS±21).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).

H01024H23360
Airbag
Sensor
Assembly P Squib
(Dual stage ±
2nd step)
DC
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1415
1609 Author: Date:
2005 SEQUOIA (RM1146U)
10 Check front passenger airbag assembly (P squib, dual stage ± 2nd step).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) From the step 9:
Disconnect the SST from connector ºCº.
(d) Connect the connector to the front passenger airbag as-
sembly.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1815, B1816, B1817 or B1818 is not output.
HINT:
Codes other than DTC B1815, B1816, B1817 and B1818 may
be output at this time, but they are not related to this check.
NG Replace front passenger airbag assembly
(see page RS±33).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).

H23966
Side Squib RH
Airbag
Sensor
Assembly C D
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1425
1619 Author: Date:
2005 SEQUOIA (RM1146U)
10 Check side airbag assembly RH (side squib RH).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) From the step 9:
Disconnect the service wire from connector ºCº.
(d) Connect the connector to the side airbag assembly RH.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1820, B1821, B1822 or B1823 is not output.
HINT:
Codes other than DTC B1820, B1821, B1822 and B1823 may
be output at this time, but they are not related to this check.
NG Replace side airbag assembly RH
(see page RS±46, RS±61).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).

H01018H23474
Side Squib LH
Airbag
Sensor
Assembly C D
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1435
1629 Author: Date:
2005 SEQUOIA (RM1146U)
10 Check side airbag assembly LH (side squib LH).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) From the step 9:
Disconnect the service wire from connector ºCº.
(d) Connect the connector to the side airbag assembly LH.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1825, B1826, B1827 or B1828 is not output.
HINT:
Codes other than DTC B1825, B1826, B1827 and B1828 may
be output at this time, but they are not related to this check.
NG Replace side airbag assembly LH
(see page RS±46, RS±61).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).

H23966
Airbag
Sensor
Assembly
C DCurtain Shield
Airbag RH Squib
DI±1446
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1640 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check curtain shield airbag assembly RH (curtain shield airbag RH squib).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) From the step 11:
Disconnect the service wire from connector ºCº.
(d) Connect the connector to the curtain shield airbag as-
sembly RH.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1830, B1831, B1832 or B1833 is not output.
HINT:
Codes other than DTC B1830, B1831, B1832 and B1833 may
be output at this time, but they are not related to this check.
NG Replace curtain shield airbag assembly RH
(see page RS±71).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).
HINT:

Perform the simulation method by selecting the check mode with the hand±held tester (see page
DI±1151).

After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page DI±1151).