2001 TOYOTA SEQUOIA relay

A23543
+B
OXR2
OXL2E1 HTR2
HTL2
H2
H4
Wire Harness Side:
Bank 1 Sensor 2, Bank 2 Sensor 2
B17416HT1BECM Connector E7OX1B E8
HT2B
OX2B
A21040
Reference (Bank 1 Sensor 1 System Drawing)
From
BatteryEFI No. 1 FuseEFI Relay
EFI No. 2 FuseHeater Oxygen
Sensor
Heater
SensorHT1A
OX1A
E2
MRELECM
DI±164
± DIAGNOSTICSENGINE
358 Author: Date:
2005 SEQUOIA (RM1146U)
17 Check for open and short in harness and connector between ECM and heated
oxygen sensor.
PREPARATION:
(a) Disconnect the heated oxygen sensor connector.
(b) Disconnect the E7 and E8 ECM connector.
CHECK:
Measure the resistance between the wire harness side connec-
tors.
OK:
Standard:
Tester ConnectionSpecified Condition
OXL2 (H2±3) ± OX1B (E8±18)Below 1 W
HTL2 (H2±1) ± HT1B (E8±1)Below 1 W
OXR2 (H4±3) ± OX2B (E7±33)Below 1 W
HTR2 (H4±1) ± HT2B (E7±5)Below 1 W
OXL2 (H2±3) or OX1B (E8±18) ±
Body ground10 kW or higher
HTL2 (H2±1) or HT1B (E8±1) ±
Body ground10 kW or higher
OXR2 (H4±3) or OX2B (E7±33) ±
Body ground10 kW or higher
HTR2 (H4±1) or HT2B (E7±5) ±
Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
Replace heated oxygen sensor.

DI±166
± DIAGNOSTICSENGINE
360 Author: Date:
2005 SEQUOIA (RM1146U)DTC No.
DTC Detecting ConditionTrouble Area
P0171
P0174When air±fuel ratio feedback is stable after warming up the
engine, fuel trim is considered to be in error on LEAN side
(2 trip detection logic)

Air induction system

Injector blockage

Mass air flow meter

Engine coolant temperature sensor

Fuel pressure

Gas leakage in exhaust system

Open or short in heated oxygen sensor (bank 1, 2 sensor 1)
circuit

Heated oxygen sensor (bank 1, 2 sensor 1)

Heated oxygen sensor heater (bank 1, 2 sensor 1)

EFI relay

PCV piping

ECM
P0172
P0175When air±fuel ratio feedback is stable after warming up the
engine, fuel trim is considered to be in error on RICH side
(2 trip detection logic)

Injector leak, blockage

Mass air flow meter

Engine coolant temperature sensor

Ignition system

Fuel pressure

Gas leakage in exhaust system

Open or short in heated oxygen sensor (bank 1, 2 sensor 1)
circuit

Heated oxygen sensor (bank 1, 2 sensor 1)

ECM
HINT:

When DTC P0171 or P0174 is recorded, the actual air±fuel ratio is on the LEAN side. When DTC
P0172 or P0175 is recorded, the actual air±fuel ratio is on the RICH side.

If the vehicle runs out of fuel, the air±fuel ratio is LEAN and DTC P0171 or P0174 may be recorded.
The MIL then comes on.

If the total of the short±term fuel trim value and long±term fuel trim value is within
35 % (engine cool-
ant temperature is more than 75 C (167F)), the system is functioning normally.

A19288
A/F Relay
A23659
Wire Harness Side:
HT
A38
Sensor 1A/F Sensor Connector
AF+
Front ViewAF±
+B A39
B17415
E7ECM Connector
HA1A
A1A+
A1A±
A2A+
A2A±HA2A
± DIAGNOSTICSENGINE
DI±175
369 Author: Date:
2005 SEQUOIA (RM1146U)
12 Check A/F relay.
PREPARATION:
Remove the A/F relay from the engine room J/B.
CHECK:
Inspect the A/F relay.
OK:
Standard:
Terminal No.ConditionSpecified Condition
3 ± 5Always10 KW or higher
3 ± 5Apply B+ between
terminals 1 and 2Below 1 W
NG Replace A/F relay.
OK
13 Check for open and short in harness and connector between ECM and A/F sen-
sor.
PREPARATION:
(a) Disconnect the A38 or A39 A/F sensor connector.
(b) Turn the ignition switch to ON.
CHECK:
(a) Measure the voltage between the +B terminal of the A/F
sensor connector and body ground.
OK:
Standard:
Tester ConnectionsSpecified Conditions
+B (2) ± Body ground9 to 14 V
PREPARATION:
(a) Turn the ignition switch to OFF.
(b) Disconnect the E7 ECM connector.
CHECK:
(a) Check the resistance.
OK:
Standard (Check for open):
Tester ConnectionsSpecified Conditions
HT (A38±1) ± HA1A (E7±2)
HT (A39±1) ± HA2A (E7±1)Below 1 W
AF+ (A38±3) ± A1A+ (E7±22)
AF+ (A39±3) ± A2A+ (E7±23)Below 1 W
AF± (A38±4) ± A1A± (E7±30)
AF± (A39±4) ± A2A± (E7±31)Below 1 W

A23512
Reference (Bank 1 Sensor 1 System Drawing):
A/F Sensor A/F Relay
Heater
Sensor
A1A+ HA1A
Duty
Control ECM
From
Battery
A/F Heater
Fuse
A1A±
To EFI Relay
DI±176
± DIAGNOSTICSENGINE
370 Author: Date:
2005 SEQUOIA (RM1146U)
Standard (Check for short):
Tester ConnectionsSpecified Conditions
HT (A38±1) or HA1A (E7±2) ± Body ground
HT (A39±1) or HA2A (E7±1) ± Body ground10 kW or higher
AF+ (A38±3) or A1A+ (E7±22) ± Body ground
AF+ (A39±3) or A2A+ (E7±23) ± Body ground10 kW or higher
AF± (A38±4) or A1A± (E7±30) ± Body ground
AF± (A39±4) or A2A± (E7±31) ± Body ground10 kW or higher
NG Replace or replace harness or connector.
OK
14 Replace air fuel ratio sensor.
NEXT

A21043
Starter Relay EFI Relay
Circuit Opening
Relay
Fuel Pump RelayMREL
FPRTr2
Tr1 EFI No.1
IGNECM
FC
NE Fuel Pump
Battery
StarterFuel Pump Resistor
AM2Ignition Switch
STA
Crankshaft Position
Sensor (NE Signal)
± DIAGNOSTICSENGINE
DI±179
373 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0230 Fuel Pump Primary Circuit
CIRCUIT DESCRIPTION
In the diagram below, when the engine is cranked, current flows from terminal STAR of the ECM to the starter
relay coil and also current flows to terminal STA of the ECM (STA signal).
When the STA signal and NE signal are input to the ECM, the Tr1 is turned ON, current flows to the coil of
the circuit opening relay, the relay switches on, power is supplied to the fuel pump, and the fuel pump oper-
ates.
While the NE signal is generated (engine running), the ECM keeps the Tr1 ON (circuit opening relay ON)
and the fuel pump also keeps operating.
The fuel pump speed is controlled at two levels (high speed or low speed) by the condition of the engine
(starting, light load, heavy load). When the engine starts (STA ON), the Tr2 in the ECM is OFF, so the fuel
pump relay closes and battery positive voltage is applied directly to the fuel pump. The fuel pump operates
at high speed.
After the engine starts while idling or light loads, since the Tr2 goes ON, power is supplied to the fuel pump
via the fuel pump resistor. The fuel pump operates at low speed.
DICEW±02

DI±180
± DIAGNOSTICSENGINE
374 Author: Date:
2005 SEQUOIA (RM1146U)DTC No.
DTC Detecting ConditionTrouble Area
P0230Open or short in fuel pump relay circuit

Open or short in fuel pump relay circuit

Fuel pump relay

Circuit opening relay

Fuel pump

ECM

A23553
G±R
1 28
A 6
BECM
AM2
W±B6
32
15 3
2 121
3 2B IA1
J5
J/CL±O
I18
Ignition SW
3
7
F10
Fusible Link BlockB±R
BI530
10 26 4
12
2
114
68
1 41
5 3L±B
AM2
52HE6
2D
2F 1J1C2F
IA4
E4
E4 IG4
IA4 2H
2H 2C 1C
1JFPR
FC
MREL B±O5
J44
J45J/C E
L
BB1G±RG±REngine Room J/B
4
2F
5V V V
IL2
25
G±O G±O
B
IG2
W±B
W±BA
ED 5 4G±RIG1
B±WB±W
Instrument Panel J/B
F9
Fuel Pump
Resister
Battery2C
W±R W±R5
6
EFI No.15
C/OPN Relay Fuel Pump
Relay
EFI Relay F19
Fuel Pump
± DIAGNOSTICSENGINE
DI±181
375 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM
HINT:
This diagnostic chart is based on premise that engine is started. If the engine is not started, proceed to prob-
lem symptoms table on DI±33.

B17411
E6E1
FPR
A21024
DI±182
± DIAGNOSTICSENGINE
376 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check voltage between terminal FPR and E1 of ECM.
CHECK:
Measure the voltage between terminals of E6 and E6 ECM con-
nectors.
OK:
Tester ConnectionConditionSpecified Condition
FPR (E6±30) ± E1 (E6±1)STA signal ON9 to 14 V
FPR (E6±30) ± E1 (E6±1)STA signal OFF0 to 3 V
OK Replace ECM (See page SF±80).
NG
2 Check fuel pump relay.
PREPARATION:
Remove the fuel pump relay from the engine room R/B.
CHECK:
Inspect the fuel pump relay.
OK:
Terminal No.ConditionSpecified Condition
3 ± 4Apply B+ between
terminals 1 and 210 KW or higher
3 ± 4AlwaysBelow 1 W
3 ± 5Always10 KW or higher
3 ± 5Apply B+ between
terminals 1 and 2Below 1 W
NG Replace fuel pump relay.
OK