2001 TOYOTA SEQUOIA Page 18

DI±612
± DIAGNOSTICSAUTOMATIC TRANSMISSION
806 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check other DTCs output (in addition to DTC P0751).
PREPARATION:
(a) Turn the ignition switch off.
(b) Connect the OBD II scan tool or hand±held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Turn on the tester.
(e) Select the item ºDIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODESº.
CHECK:
Read the DTCs using the OBD II scan tool or the hand±held tester.
RESULT:
Display (DTC output)Proceed to
Only ºP0751º is outputA
ºP0751º and other DTCsB
HINT:
If any other codes besides ºP0751º are output, perform troubleshooting for those DTCs first.
B Go to DTC chart (See page DI±573).
A

D11991
Shift solenoid S1:
(+) (±)
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±613
807 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check shift solenoid valve S1 operation.
PREPARATION:
Remove the shift solenoid valve S1 (See page AT±10).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
20C (68F)
Solenoid Connector (S1) ± Solenoid
Body (S1)11 to 15 W
CHECK:
Connect the positive (+) lead to the terminal of the solenoid con-
nector, and the negative (±) lead to the solenoid body.
OK:
The solenoid makes an operating sound.
NG Replace shift solenoid valve S1
(See page AT±10).
OK
3 Inspect valve body (See page AT±10).
OK:
There are no foreign objects on each valve.
NG Repair or replace valve body.
OK
Repair or replace transmission (See page
AT±25).

ECM command gearshift
Shift solenoid valve S21st 2nd 3rd 4th 5th
OFF ON
ON OFF OFF
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±617
811 Author: Date:
2005 SEQUOIA (RM1146U) ON malfunction (E)
Turbine speed ± Output speed x 5th gear ratio
(NT ± NO x 5th gear ratio)1,000 rpm or more
INSPECTION PROCEDURE
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TESTº.
(g) According to the display on the tester, perform the ºACTIVE TESTº.
HINT:
While driving, the shift position can be forcibly changed with the hand±held tester.
Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you
to confirm the problem (See page DI±567).
ItemTest DetailsDiagnostic Note
SHIFT
[Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]
Less than 50 km/h (31 mph)
[Others]

Press º"º button: Shift up

Press ºuº button: Shift down
Possible to check the operation of
the shift solenoid valves.
HINT:

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

The 4th to 5th up±shiftings must be performed with the accelerator pedal released.

The 5th to 4th down±shiftings must be performed with the accelerator pedal released.

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

The shift position commanded by the ECM is shown in the DATA LIST (SHIFT) display on the hand±
held tester.

The shift solenoid valve S2 is turned on/off normally when the shift lever is in the D position:

DI±618
± DIAGNOSTICSAUTOMATIC TRANSMISSION
812 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check other DTCs output (in addition to DTC P0756).
PREPARATION:
(a) Turn the ignition switch off.
(b) Connect the OBD II scan tool or hand±held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Turn on the tester.
(e) Select the item ºDIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODESº.
CHECK:
Read the DTCs using the OBD II scan tool or the hand±held tester.
RESULT:
Display (DTC output)Proceed to
Only ºP0756º is outputA
ºP0756º and other DTCsB
HINT:
If any other codes besides ºP0756º are output, perform troubleshooting for those DTCs first.
B Go to DTC chart (See page DI±573).
A

D11992
Shift solenoid S2:
(+) (±)
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±619
813 Author: Date:
2005 SEQUOIA (RM1146U)
2 Inspect shift solenoid valve S2 operation.
PREPARATION:
Remove the shift solenoid valve S2 (See page AT±10).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
20C (68F)
Solenoid Connector (S2) ± Solenoid
Body (S2)11 to 15 W
CHECK:
Connect the positive (+) lead to the terminal of the solenoid con-
nector, and the negative (±) lead to the solenoid body.
OK:
The solenoid makes an operating sound.
NG Replace shift solenoid valve S2
(See page AT±10).
OK
3 Inspect valve body (See page AT±10).
OK:
There are no foreign objects on each valve.
NG Repair or replace valve body.
OK
Repair or replace transmission (See page
AT±25).

ECM command gearshift
Shift solenoid valve SR1st 2nd 3rd 4th 5th
OFF
OFF OFF
Shift solenoid valve SL1OFF
OFF OFFON
ON OFF
OFF DI±622
± DIAGNOSTICSAUTOMATIC TRANSMISSION
816 Author: Date:
2005 SEQUOIA (RM1146U) OFF malfunction (C)
Output record from ECM for 4th " 5th upshiftingRecorded
[ON malfunction]
2 detections are necessary per driving cycle
1st detection; temporary flag ON
2nd detection; temporary pending fault code ON
Turbine speed ± Output speed x 1st gear ratio
(NT ± NO x 1st gear ratio)150 rpm or more
INSPECTION PROCEDURE
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TESTº.
(g) According to the display on the tester, perform the ºACTIVE TESTº.
HINT:
While driving, the shift position can be forcibly changed with the hand±held tester.
Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you
to confirm the problem (See page DI±567).
ItemTest DetailsDiagnostic Note
SHIFT
[Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]
Less than 50 km/h (31 mph)
[Others]

Press º"º button: Shift up

Press ºuº button: Shift down
Possible to check the operation of
the shift solenoid valves.
HINT:

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

The 4th to 5th up±shiftings must be performed with the accelerator pedal released.

The 5th to 4th down±shiftings must be performed with the accelerator pedal released.

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

The shift position commanded by the ECM is shown in the DATA LIST (SHIFT) display on the hand±
held tester.

The shift solenoid valve SR and SL1 is turned on/off normally when the shift lever is in the D position:

D11993
(+) (±) Shift Solenoid Valve SR:
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±623
817 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check other DTCs output (in addition to DTC P0771).
PREPARATION:
(a) Turn the ignition switch off.
(b) Connect the OBD II scan tool or hand±held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Turn on the tester.
(e) Select the item ºDIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODESº.
CHECK:
Read the DTCs using the OBD II scan tool or the hand±held tester.
RESULT:
Display (DTC output)Proceed to
Only ºP0771º is outputA
ºP0771º and other DTCsB
HINT:
If any other codes besides ºP0771º are output, perform troubleshooting for those DTCs first.
B Go to DTC chart (See page DI±573).
A
2 Inspect shift solenoid valve SR operation.
PREPARATION:
Remove the shift solenoid valve SR (See page AT±10).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
20C (68F)
Solenoid Connector (SR) ± Solenoid
Body (SR)11 to 15 W
CHECK:
Connect the positive (+) lead to the terminal of the solenoid con-
nector, and the negative (±) lead to the solenoid body.
OK:
The solenoid makes an operating sound.
NG Replace shift solenoid valve SR
(See page AT±10).
OK

D12795
12
(±)(+)
12
Shift Solenoid Valve SL1:
DI±624
± DIAGNOSTICSAUTOMATIC TRANSMISSION
818 Author: Date:
2005 SEQUOIA (RM1146U)
3 Inspect shift solenoid valve SL1.
PREPARATION:
Remove the shift solenoid valve SL1 (See page AT±10).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
20C (68F)
1 ± 25.0 to 5.6 W
CHECK:
Connect the positive (+) lead with a 21 W bulb to terminal 2 and
the negative (±) lead to terminal 1 of the solenoid valve connec-
tor, then check the movement of the valve.
OK:
The solenoid makes an operating sound.

NG Replace the shift solenoid valve SL1
(See page AT±10).
OK
4 Inspect valve body (See page AT±10).
OK:
There are no foreign objects on each valve.
NG Repair or replace valve body.
OK
Repair or replace transmission (See page
AT±25).