2001 TOYOTA SEQUOIA Page 18

DI±572
± DIAGNOSTICSAUTOMATIC TRANSMISSION
766 Author: Date:
2005 SEQUOIA (RM1146U)
2. ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one method
to shorten labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the tester.
(f) Select the item ºDIAGNOSIS / ENHANCED OBD II / ACTIVE TESTº.
(g) According to the display on the tester, perform the ºACTIVE TESTº.
ItemTest DetailsDiagnostic Note
SHIFT
[Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]
Less than 50 km/h (31 mph)
[Others]

Press º"º button: Shift up

Press ºuº button: Shift down
Possible to check the operation of
the shift solenoid valves.
LOCK UP
[Test Details]
Control the shift solenoid SLU to set the automatic transmission to the
lock±up condition.
[Vehicle Condition]

Throttle valve opening angle: Less than 35 %

Vehicle Speed: 60 km/h (37 mph) or more
Possible to check the SLU opera-
tion.
LINE PRESS UP *
[Test Details]
Operate the shift solenoid SLT and raise the line pressure.
[Vehicle Condition]

Vehicle Stopped.

IDL: ON
[HINT]
OFF: Line pressure up (When the active test of ºControl the Line Pres-
sure Upº is performed, the ECM commands the SLT solenoid to turn
off).
ON: No action (normal operation)
±
*: ºLINE PRESS UPº in the ACTIVE TEST is performed to check the line pressure changes by connecting
the SST to the automatic transaxle, which is used in the HYDRAULIC TEST (See page DI±540) as well.
HINT:
The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.

DIDJ4±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±573
767 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the parts listed in the table below and proceed to the page
given.
HINT:
*1 :
... The MIL (Malfunction Indicator Lamp) lights up
*2 :  ... The ECM memorizes the trouble code if the ECM detects the DTC detection condition.
This DTC may be output when the clutch, brake and gear components etc. inside the automatic trans-
mission are damaged.
DTC No.
(See Page)Detection ItemTrouble AreaMIL *1Memory *2
P0500
(DI±278)Vehicle Speed Sensor ºAº
Open or short in speed sensor (SP2) circuit
Speed sensor (SP2)
ECM


P0705
(DI±576)Transmission Range Sensor Cir-
cuit Malfunction (PRNDL Input)Open or short in park/neutral position switch circuit
Park/neutral position switch
ECM


P0710
(DI±582)Transmission Fluid Temperature
Sensor ºAº CircuitOpen or short in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0711
(DI±588)Transmission Fluid Temperature
Sensor ºAº PerformanceTransmission wire (ATF temperature sensor No.1)

P0712
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit Low InputShort in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0713
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit High InputOpen in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0717
(DI±591)Input Speed Sensor Circuit No
Signal
Open or short in speed sensor (NT) circuit
Speed sensor (NT)
ECM
Automatic transmission (clutch, brake or gear, etc.)


P0722
(DI±596)Output Speed Sensor Circuit No
Signal
Open or short in speed sensor (SP2) circuit
Speed sensor (SP2)
ECM
Automatic transmission (clutch, brake or gear, etc.)


P0724
(DI±600)Brake Switch ºBº Circuit High
Short in stop light switch signal circuit
Stop light switch
ECM


P0748
(DI±603)Pressure Control Solenoid ºAº
Electrical
(Shift Solenoid Valve SL1)Open or short in shift solenoid valve SL1 circuit
Shift solenoid valve SL1
ECM


P0751
(DI±608)Shift Solenoid ºAº Performance
(Shift Solenoid Valve S1)Shift solenoid valve S1 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P0756
(DI±614)Shift Solenoid ºBº Performance
(Shift Solenoid Valve S2)Shift solenoid valve S2 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P0771
(DI±620)Shift Solenoid ºEº Performance
(Shift Solenoid Valve SR)
Shift solenoid valve SR remains open or closed
Shift solenoid valve SL1 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)



DIDJ5±01
DI±576
± DIAGNOSTICSAUTOMATIC TRANSMISSION
770 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT INSPECTION
DTC P0705 Transmission Range Sensor Circuit Mal-
function (PRNDL Input)
CIRCUIT DESCRIPTION
The park/neutral position switch detects the shift lever position and sends signals to the ECM.
DTC No.DTC Detection ConditionTrouble Area
P0705
(2±trip detection logic)

All switches are OFF simultaneously for NSW, R, N, D, 3 and
2 positions.

2 or more switches are ON simultaneously for NSW, R, D, 3
and 2 positions.

Open or short in park/neutral position switch circuit

Park/neutral position switch

ECM
MONITOR DESCRIPTION
These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral
position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that engine can be started
only when the shift lever is in the P or N position.
The park/neutral position switch sends a signal to the ECM according to the shift position (NSW, R, D, 3 or
2).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position
signal simultaneously. The ECM will turn on the MIL and store the DTC.
MONITOR STRATEGY
Related DTCsP0705Park/neutral position switch/Verify switch input
Required sensors/ComponentsPark/neutral position switch
Frequency of operationContinuous
DtiCondition (A)2 sec.DurationCondition (B)60 sec.
MIL operation2 driving cycle
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not present.See page DI±545
Ignition switchON
Battery voltage10.5 V or more

D14154
Switch Side:
(Connector Front View):
P1
DI±580
± DIAGNOSTICSAUTOMATIC TRANSMISSION
774 Author: Date:
2005 SEQUOIA (RM1146U)
1 Inspect park/neutral position switch.
PREPARATION:
(a) Jack up the vehicle.
(b) Disconnect the park/neutral position switch connector.
CHECK:
Measure the resistance according to the value(s) in the table
below when the shift lever is moved to each position.
OK:
Shift PositionTester ConnectionSpecified Condition
P2 ± 6 and 4 ± 5Below 1 W
Except P=10 kW or higher
R2 ± 1Below 1 W
Except R=10 kW or higher
N2 ± 9 and 4 ± 5Below 1 W
Except N=10 kW or higher
D2 ± 7Below 1 W
Except D=10 kW or higher
32 ± 3Below 1 W
Except 3=10 kW or higher
22 ± 8Below 1 W
Except 2=10 kW or higher
NG Replace park/neutral position switch
(See page AT±9).
OK

D14155
E8E7E6E5E4
R(+)
D(+)2(+)
3(+)
STAR/NSW(+)
ECM:
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±581
775 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check harness and connector (Park/neutral position switch ± ECM).
PREPARATION:
(a) Connect the park/neutral position switch connector.
(b) Turn the ignition switch ON.
CHECK:
Measure the voltage according to the value(s) in the table be-
low when the shift lever is moved to each position.
OK:
Shift PositionTester connectionSpecified condition
P and NE7 ± 8 (STAR/NSW) ± Body groundBelow 2 V
Except P and N=10 to 14 V
RE5 ± 11 (R) ± Body ground10 to 14 V*
Except R=Below 1 V
D and 4E5 ± 21 (D) ± Body ground10 to 14 V
Except D and 4=Below 1 V
3E5 ± 19 (3) ± Body ground10 to 14 V
Except 3=Below 1 V
2 and LE5 ± 10 (2) ± Body ground10 to 14 V
Except 2 and L=Below 1 V
HINT:
*: The voltage will drop slightly due to lighting up of the back up
light.
NG Repair or replace the harness or connector
(See page IN±35).
OK
Replace the ECM (See page SF±80).

DI±584
± DIAGNOSTICSAUTOMATIC TRANSMISSION
778 Author: Date:
2005 SEQUOIA (RM1146U)
MONITOR STRATEGY
P0710ATF temperature sensor/Range check (Fluttering)
Related DTCsP0712ATF temperature sensor/Range check (Low resistance)Related DTCs
P0713ATF temperature sensor/Range check (High resistance)
Required sensors/ComponentsATF temperature sensor (TFT sensor)
Frequency of operationContinuous
Duration0.5 sec.
MIL operationImmediate
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever these
DTCs are not present.See page DI±545
Range check (Fluttering, Low resistance)
The typical enabling condition is not avail-
able.±
Range check (High resistance)
Time after engine start15 min. or more±
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
Range check (Fluttering)
TFT (transmission fluid temperature) sensor resistance
Less than 79 W
or
More than 156 kW
Range check (Low resistance)
TFT (transmission fluid temperature) sensor resistanceLess than 79 W
Range check (High resistance)
TFT (transmission fluid temperature) sensor resistanceMore than 156 kW
COMPONENT OPERATING RANGE
ParameterStandard value
TFT (transmission fluid temperature) sensorAtmospheric temperature to approx. 130°C (266°F)

1
152 3 4 5 6 7 8
9 10 11 12
13 14
D11994OT+OT±
E1
Transmission Wire Side:
(Connector Front View):
DI±586
± DIAGNOSTICSAUTOMATIC TRANSMISSION
780 Author: Date:
2005 SEQUOIA (RM1146U)
1 Inspect transmission wire (ATF temperature sensor No.1).
PREPARATION:
Disconnect the transmission wire connector from the transmis-
sion.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
2 (OT±) ± 10 (OT+)79 W to 156 kW
2 (OT±) ± Body ground10 kW or higher
10 (OT+) ± Body ground10 kW or higher
HINT:
If the resistance is out of the specified range with either the ATF
temperature shown in the table below, the driveability of the ve-
hicle may decrease.
ATF TemperatureSpecified Condition
20°C (68°F)3 to 4 kW
110°C (230°F)0.22 to 0.28 kW
NG Repair or replace the transmission wire
(ATF temperature sensor No.1)
(See page AT±7).
OK

D14161
E8E7E6E5E4ECM:
THO1
E2
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±587
781 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check harness and connector (Transmission wire ± ECM).
PREPARATION:
(a) Connect the transmission wire connector.
(b) Disconnect the connector of the ECM.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
E7 ± 24 (THO1) ± E8 ± 28 (E2)79 W to 156 kW
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionSpecified Condition
E7 ± 24 (THO1) ± Body ground10 kW or higher
E8 ± 28 (E2) ± Body ground=
NG Repair or replace the harness or connector
(See page IN±35).
OK
Replace the ECM (See page SF±80).