2001 TOYOTA SEQUOIA warning

RS0BD±11
± SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
RS±31
3314 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
CAUTION:

If the steering wheel pad has been dropped, or there are cracks, dents or other defects in the
case or connector, replace the steering wheel pad with a new one.

When installing the steering wheel pad, take care it is not pinched between other parts.

Never use airbag parts from another vehicle. When replacing parts, replace them with new
ones.
1. INSTALL SPIRAL CABLE (SEE PAGE SR±23)
2. INSTALL STEERING COLUMN COVER LOWER (SEE PAGE SR±23)
3. INSTALL STEERING WHEEL (SEE PAGE SR±23)
4. INSTALL STEERING WHEEL PAD (SEE PAGE SR±23)
5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
6. PERFORM INITIALIZATION (SEE PAGE SR±23)
Some system need initialization when disconnecting the cable from the negative battery terminal.
7. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)

H23211
RS±44
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT PASSENGER AIRBAG ASSEMBLY
3327 Author: Date:
2005 SEQUOIA (RM1146U)
11. CONNECT AIRBAG CONNECTOR
(a) Connect the airbag connector as shown in the illustration.
(b) Attach the connector clamp to the reinforcement.
12. INSTALL COWL TRIM BOARDS
(SEE PAGE BO±97)
13. INSTALL FRONT DOOR SCUFF PLATES
(SEE PAGE BO±97)
14. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
15. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
16. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)

H24314
H24313
H24312
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY (Power Adjuster Type)
RS±59
3342 Author: Date:
2005 SEQUOIA (RM1146U)
(d) Install the 2 screws to the seat cushion lower shield.
(e) Install the 2 screws to the seat cushion inner shield.
(f) Install the 2 screws to the seat cushion outer shield.
(g) Install the screw to the seat cushion outer shield.
8. INSTALL SLIDE KNOB AND RECLINING KNOB
9. INSTALL HEADREST
10. INSTALL FRONT SEAT
Mount the front seat to the vehicle.
NOTICE:
Be careful not to damage the body.
(a) w/ Side airbag:
Connect the connectors.
(b) Connect the connectors.
(c) Slide the front seat to the rearmost position.
(d) Tighten the bolts on the front side temporarily, starting
from the bolt on the inner side.
(e) Tighten them completely.
Torque: 37 N´m (377 kgf´cm, 27 ft´lbf)
(f) Slide the front seat to the foremost position.
(g) Tighten the bolts on the rear side temporarily, starting
from the bolt on the inner side.
(h) Tighten them completely.
Torque: 37 N´m (377 kgf´cm, 27 ft´lbf)
11. INSTALL SEAT TRACK COVERS
12. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
13. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
14. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)

H24333
H24331ClawsClip
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY (Manual Adjuster Type)
RS±69
3352 Author: Date:
2005 SEQUOIA (RM1146U)
6. INSTALL VERTICAL ADJUSTER HANDLE
(a) Install the vertical adjuster handle with the 2 screws.
(b) Install the vertical adjuster handle cap.
7. INSTALL RECLINING ADJUSTER RELEASE HANDLE
8. INSTALL SEAT CUSHION OUTER SHIELD
Install the seat cushion outer shield with the screw.
9. INSTALL HEADREST
10. INSTALL FRONT SEAT
Mount the front seat to the vehicle.
NOTICE:
Be careful not to damage the body.
(a) w/ Side airbag:
Connect the airbag connector.
(b) Connect the connectors.
(c) Slide the front seat to the rearmost position.
(d) Tighten the bolts on the front side temporarily, starting
from the bolt on the inner side.
(e) Tighten them completely.
Torque: 37 N´m (377 kgf´cm, 27 ft´lbf)
(f) Slide the front seat to the foremost position.
(g) Tighten the bolts on the rear side temporarily, starting
from the bolt on the inner side.
(h) Tighten them completely.
Torque: 37 N´m (377 kgf´cm, 27 ft´lbf)
11. INSTALL SEAT TRACK COVERS
12. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
13. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
14. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)

RS0TH±07
H23897
RS±80
± SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
3363 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:

Use the same procedures for the RH side and LH side.

The procedures listed below are for the LH side.
1. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY
(a) Install the curtain shield airbag assembly with the 13
bolts.
Torque: 9.8 N´m (100 kgf´cm, 7 ft´lbf)
CAUTION:
Pay attention not to twist the deployment section of the cur-
tain shield airbag assembly.
NOTICE:

If the curtain shield airbag assembly has been
dropped, or there are cracks, dents or other defects
in the case or connector, replace the curtain shield
airbag assembly with a new one.

When installing the curtain shield airbag assembly,
take care it is not pinched between other parts.

Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
(b) Connect the connector of the curtain shield airbag as-
sembly.
2. INSTALL ROOF HEADLINING (SEE PAGE BO±108)
3. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
4. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
5. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)

RS0BO±11
H23231
± SUPPLEMENTAL RESTRAINT SYSTEMAIRBAG SENSOR ASSEMBLY
RS±85
3368 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
NOTICE:

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.

Never reuse the airbag sensor assembly involved in
a collision when the airbag has deployed.

If the airbag sensor assembly center has been
dropped, or there are any cracks, dents or other de-
fects in the case, bracket or connector, replace it with
a new one.

When installing the airbag sensor assembly center,
be careful that the SRS wiring does not interfere with
other parts and that it is not pinched between other
parts.

After installing, shake the airbag sensor assembly to
check that there is no looseness.
1. INSTALL AIRBAG SENSOR ASSEMBLY
(a) Install the airbag sensor assembly with the 4 bolts.
Torque: 17.5 N´m (179 kgf´cm, 13 ft´lbf)
(b) Connect the airbag sensor holder (with connectors).
2. INSTALL FRONT CONSOLE BOX ASSEMBLY
(SEE PAGE BO±89)
3. INSTALL REAR CONSOLE BOX ASSEMBLY
(SEE PAGE BO±89)
4. INSTALL UPPER CONSOLE PANEL
(SEE PAGE BO±89)
5. INSTALL SHIFTING HOLE COVER
(SEE PAGE BO±89)
6. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
7. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
8. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)

H23879
RS11I±01
RS±90
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
3373 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:

Use the same procedures for the RH side and LH side.

The procedures listed below are for the LH side.
NOTICE:

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.

Never reuse the front airbag sensor involved in a col-
lision when the airbag has deployed.

If the front airbag sensor center has been dropped, or
there are any cracks, dents or other defects in the
case, bracket or connector, replace it with a new one.

When installing the front airbag sensor center, be
careful that the SRS wiring does not interfere with
other parts and that it is not pinched between other
parts.

After installing, shake the front airbag sensor to
check that there is no looseness.
1. INSTALL FRONT AIRBAG SENSORS LH
(a) Install the front airbag sensors LH with the 2 nuts.
Torque: 17.5 N´m (179 kgf´cm, 13 ft´lbf)
(b) Connect the front airbag sensor connectors.
2. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
3. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
4. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)

RS11N±01
H20066
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG SENSOR ASSEMBLY
RS±95
3378 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:

Use the same procedures for the RH side and LH side.

The procedures listed below are for the LH side.
NOTICE:

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.

Never reuse the side airbag sensor assembly in-
volved in a collision when the airbag has deployed.

If the side airbag sensor assembly center has been
dropped, or there are any cracks, dents or other de-
fects in the case, bracket or connector, replace it with
a new one.

When installing the side airbag sensor assembly, be
careful that the SRS wiring does not interfere with
other parts and that it is not pinched between other
parts.

After installing, shake the side airbag sensor assem-
bly to check that there is no looseness.
1. INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH
(a) Install the side airbag sensor assembly LH with the 3
bolts.
Torque: 17.5 N´m (179 kgf´cm, 13 ft´lbf)
(b) Connect the connector to the side airbag sensor assem-
bly LH.
2. INSTALL FRONT SEAT OUTER BELT RETRACTOR
(SEE PAGE BO±172)
3. INSTALL CENTER PILLAR LOWER GARNISH
(SEE PAGE BO±108)
4. INSTALL FRONT SEAT OUTER BELT FLOOR AN-
CHOR (SEE PAGE BO±108 )
5. INSTALL REAR DOOR SCUFF PLATE
(SEE PAGE BO±97)
6. INSTALL FRONT DOOR SCUFF PLATE
(SEE PAGE BO±97)
7. CONNECT CABLE TO NEGATIVE BATTERY TERMI-
NAL
8. PERFORM INITIALIZATION (SEE PAGE BE±77)
Some system need initialization when disconnecting the cable
from the negative battery terminal.
9. INSPECT SRS WARNING LIGHT (SEE PAGE DI±1137)