2001 TOYOTA SEQUOIA abs system

A23482
Purge VSV
Vent Valve
Vacuum Pump
EVAP Pressure
Positive
Leak Pressure
sec NegativeONON
Sequence
TimeA
10
sec60
Within 15 minutes
sec ON
First 0.02 inch
BCD
OK Malfunction
ON: Open
OFF: Closed
OFF: Vent ON: Closed
10
Standard
sec60
E
EVAP Pressure when 0.02 Inch Orifice High±flow malfunction: DI±448
± DIAGNOSTICSENGINE
642 Author: Date:
2005 SEQUOIA (RM1146U)
(b) P043F: 0.02 inch orifice high±flow
In operation B, the vacuum pump creates negative pressure (vacuum) through the 0.02 inch orifice. The
EVAP system pressure is then measured by the ECM using the pressure sensor to determine the 0.02 inch
leak pressure standard. If the pressure is higher than ±1.06 kPa (±7.95 mmHg)*, the ECM interprets this as
a high±flow malfunction in the 0.02 inch orifice, and stops the EVAP system monitor. The ECM then illumi-
nates the MIL and sets the DTC (2 trip detection logic).
*: The threshold varies according to the atmospheric pressure measured in operation A. The value described
above is based on a atmospheric pressure of 100 kPa (750.1 mmHg): absolute pressure.
MONITOR STRATEGY
RltdDTCP043E0.02 inch orifice clog (built±in pump module)Related DTCsP043F0.02 inch orifice high±flow (built±in pump module)
Required sensors/componentsPump module
Frequency of operationOnce per driving cycle
DurationWithin 2 min. (varies with amount of fuel in tank)
MIL operation2 driving cycle
Sequence of operationNone

± DIAGNOSTICSENGINE
DI±463
657 Author: Date:
2005 SEQUOIA (RM1146U)Components
Operations
CanisterContains activated charcoal to absorb EVAP (Evaporative Emissions) generated in fuel tank.
Cut±off valveLocated in fuel tank. Valve floats and closes when fuel tank is 100 % full.
Purge VSV (Vacuum
Switching Valve)Opens or closes line between canister and intake manifold. ECM uses purge VSV to control EVAP purge flow. In order
to discharge EVAP absorbed by canister to intake manifold, ECM opens purge VSV. EVAP discharge volume to intake
manifold controlled by purge VSV duty cycle ratio (current±carrying time). (Open: ON, Close: OFF)
Refueling valve
Controls EVAP pressure from fuel tank to canister. Valve consists of diaphragm, spring and restrictor (diameter: 0.08
inch). When fuel vapor and pressure inside fuel tank increase, valve opens. While EVAP purged, valve closes and re-
strictor prevents large amount of vacuum from affecting pressure in fuel tank. Valve opened while refueling. When valve
open, adding fuel into fuel tank possible.
Roll±over valveLocated in fuel tank. Valve closes by its own weight when vehicle overturns to prevent fuel from spilling out.
Service portUsed for connecting vacuum gauge for inspecting EVAP system.
Soak timerBuilt into ECM. To ensure accurate EVAP monitor, measures 5 hours* after ignition switch turned to OFF. This allows
fuel to cool down, stabilizing Fuel Tank Pressure (FTP). When approx. 5 hours
* elapsed, ECM activates.
Pump moduleConsists of (a) to (d) below. Pump module cannot be disassembled.
(a) Vent valve
Vents and closes EVAP system. When ECM turns valve ON, EVAP system closed. When, ECM turns valve OFF, EVAP
system vented. Negative pressure (vacuum) created in EVAP system to check for EVAP leaks by closing purge VSV,
turning on vent valve (closed) and operating vacuum pump (refer to fig. 1).
(b) Pressure sensorIndicates pressure as voltages. ECM supplies regulated 5 V to pressure sensor, and uses feedback from sensor to
monitor EVAP system pressure (refer to fig 2).
(c) Vacuum pumpCreates negative pressure (vacuum) in EVAP system for leak check.
(d) 0.02 inch orificeHas opening with 0.02 inch diameter. Vacuum produced through orifice by closing purge VSV, turning off vent valve and
operating vacuum pump, to monitor 0.02 inch leak pressure. 0.02 inch leak pressure indicates small leak of EVAP.
HINT:
*:If the engine coolant temperature is not below 35C after 5 hours after the ignition switch is turned off, the
monitor check starts 2 hours later. If it is still not below 35C 7 hours after the ignition switch is turned off,
the monitor check starts 2.5 hours later.

D14171
Line Pressure
Control Pressure
Current Flow to Solenoid
D14172
ON
OFF
1 cycle
D14173
DI±656
± DIAGNOSTICSAUTOMATIC TRANSMISSION
850 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2714 Pressure Control Solenoid ºDº Performance
(Shift Solenoid Valve SLT)
SYSTEM DESCRIPTION
The linear solenoid valve (SLT) controls the transmission line
pressure for smooth transmission operation based on signals
from the throttle position sensor and the vehicle speed sensor.
The ECM adjusts the duty cycle of the SLT solenoid valve to
control hydraulic line pressure coming from the primary regula-
tor valve. Appropriate line pressure assures smooth shifting
with varying engine outputs.
(*): Duty Ratio
The duty ratio is the ratio of the period of continuity in one cycle.
For example, if A is the period of continuity in one cycle, and B
is the period of non±continuity, then
Duty Ratio = A/(A + B) x 100 (%)
DTC No.DTC Detection ConditionTrouble Area
P2714
ECM detects a malfunction on SLT (ON side) according to the
revolution difference of the turbine and the output shaft, and
also by the oil pressure. (2±trip detection logic)
Shift solenoid valve SLT remains open or closed

Valve body is blocked

Automatic transmission (clutch, brake or gear, etc.)
MONITOR DESCRIPTION
The ECM calculates the amount of heat absorbed by the friction material based on the difference in revolu-
tion (clutch slippage) between the turbine and output shaft. The ECM turns on the MIL and outputs this DTC
when the amount of heat absorption exceeds the specified value.
When the shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force de-
creases.
NOTE: If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer
be drivable.
DIDJL±01

DIDLU±01
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±891
1085 Author: Date:
2005 SEQUOIA (RM1146U)
ABS WITH EBD & BA & TRAC & VSC SYSTEM
PRECAUTION
NOTICE:
When disconnecting the battery terminal, initialize the following system after the terminal is recon-
nected.
System NameSee Page
Back Door Power Window Control SystemBE±77

When there is a malfunction in the contact point of the terminals or installation problems with
parts, removal and installation of the suspected problem parts may return the system to the
normal condition either completely or temporarily.

In order to determine the malfunctioning area, be sure to check the conditions at the time the
malfunction occurred, such as by DTC output and freeze frame data output, and record it before
disconnecting each connector or removing and installing parts.

Since the ABS with EBD & BA & TRAC & VSC systems may be influenced by a malfunction in
the other systems, be sure to check for DTCs in the other systems.

Be sure to remove and install the ABS & VSC actuator and each sensor with the IG switch OFF
unless specified in the inspection procedure.

When removing and installing the ABS & VSC actuator and each sensor, be sure to check that
the normal display is output in test mode inspection and in DTC output inspection after instal-
ling all the parts.

After replacing the yaw rate sensor and/or the ABS & VSC actuator assembly, make sure to per-
form yaw rate and deceleration sensors' zero point calibration
(See page DI±897).

The CAN communication system is used for data communication between the skid control ECU
(included in the actuator), the steering angle sensor, and the yaw rate sensor (the deceleration
sensor is included). If there is trouble in the CAN communication line, the DTC of the commu-
nication line is output.

If the DTC of the CAN communication line is output, repair the malfunction and troubleshoot
the ABS with EBD & BA & TRAC & VSC systems.

Since the CAN communication line has its own length and route, it can not be repaired tempo-
rarily with the bypass wire, etc.

DIDLV±01
F17996
Front Speed SensorABS & VSC Actuator
(w/ Skid Control ECU)Level Warning Switch
Rear Speed Sensor Rear Speed Sensor Rotor
Front Speed
Sensor Rotor
Parking Brake SwitchStop Light Switch
Center Diff. Lock Switch *1
TRAC OFF Switch *2
Steering Angle Sensor
DLC3Brake Inhibit RelayTranslate ECU
VSC BuzzerBrake Booster
(Including Active Brake Booster
Solenoid, Delta S Sensor and Boost-
er Pedal Switch)
Master Cylinder
Pressure Sensor
Front Speed Sensor Rotor
Front Speed Sensor
Yaw Rate Sensor
(Including Deceleration Sensor)
ABS Warning Light
VSC TRAC Warning light
VSC OFF Indicator Light *
1
TRAC OFF Indicator Light *2
BRAKE Warning Light
SLIP Indicator Light
*1: Only for 4WD
*2: Only for 2WDCenter Diff. Lock
Position Switch
DI±892
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1086 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

DIDLW±01
F19153
Speed Sensor
(Each Wheel)
Stop Lamp Switch
Parking Brake Switch
Delta S Sensor
Yaw Rate
(Deceleration) SensorABS & VSC Actuator
Skid Control
ECUCombination
Meter
Translate
ECUSteering Angle
Sensor
4WD ECU
ECM
CAN Communication SystemAir Suspension ECU (*1): CAN1 Circuit
(*2): CAN2 Circuit
(*3): Vehicle CAN Circuit(*2)
(*3) (*1)
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±893
1087 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM

DIDLX±01
DI±894
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1088 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
1. SYSTEM DESCRIPTION
HINT:

The yaw rate sensor and deceleration sensor are combined and in a single unit. This unit communi-
cates with the skid control ECU through the CAN communication system.

No changes have been made to the communication method between the VSC system and ECM. How-
ever, the communication method between the Translate ECU and ECM has been changed from serial
to CAN communication.
(a) ABS
(Anti±lock Brake System)
The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking
on a slippery surface.
(b) EBD
(Electronic Brake force Distribution)
The EBD control utilizes ABS, realizing proper brake force distribution between front and rear wheels
in accordance with driving conditions.
In addition, during braking while cornering, it also controls the brake forces of the right and left wheels,
helping to maintain vehicle behavior.
(c) BA (Brake Assist)
The primary purpose of the brake assist system is to provide an auxiliary brake force to assist the driver
who cannot generate a large enough brake force during emergency braking, thus helping to maximize
the vehicle's braking performance.
(d) TRAC
(Traction Control)
The TRAC system helps prevent the drive wheels from slipping if the driver presses down on the accel-
erator pedal excessively when starting off or accelerating on a slippery surface.
(e) VSC
(Vehicle Stability Control)
The VSC system helps prevent the vehicle from slipping sideways as a result of strong front wheel skid
or strong rear wheel skid during cornering.
2. ABS with EBD & BA & TRAC & VSC OPERATION
(a) The skid control ECU calculates vehicle stability tendency based on signals from the speed sensor,
yaw rate (deceleration) sensor and steering angle sensor. In addition, it evaluates the results of the
calculations to determine whether any control actions (control of the engine output torque by electronic
throttle control and of the wheel brake pressure by the brake actuator) should be implemented.
(b) The SLIP indicator blinks and the VSC buzzer sounds to inform the driver that the VSC system is oper-
ating. The SLIP indicator also blinks when TRAC is operating, and the operation being performed is
displayed.
3. FAIL SAFE FUNCTION
(a) When a failure occurs in the ABS & BA & TRAC & VSC systems, the ABS and VSC warning lights come
on and ABS & BA & TRAC & VSC operations are prohibited. In addition to this, when there is a failure
that disables EBD operation, the brake warning light also comes on and EBD operation is prohibited.
(b) If some control is prohibited due to a malfunction during its operation, that control will be cut off gradual-
ly not to change the stability of the vehicle suddenly.

DI939±04
Vehicle Brought to Workshop
Customer Problem Analysis
P. DI±896
Check and Clear DTC
P. DI±911Items inside
are titles of pages in this manual,
with the page number in the bottom portion. See
the pages for detailed explanations.
Problem Symptom ConfirmationSymptom Simulation
P. IN±24
Symptom
does not occur
Symptom
occurs
DTC Check
P. DI±911
Sensor CheckCircuit Inspection
DTC Chart
P. DI±921Trouble codeProblem Symptoms Table
P. DI±905
Check for Fluid Leakage
P. DI±1059
Identification of Problem
Normal system code
Repair
Confirmation Test
End
1
2
3
4
5
67
89
10
11Step 2, 5, 8, 9, 11:
P. DI±925 ± DI±1057
Diagnostic steps permitting use of the
hand±held tester.
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±895
1089 Author: Date:
2005 SEQUOIA (RM1146U)
HOW TO PROCEED WITH TROUBLESHOOTING
Troubleshoot in accordance with the following procedures: