2001 TOYOTA SEQUOIA door lock

BO45T±01
H16689
Back Door Side Garnish
Back Door Center Garnishw/o Rear spoiler:
High Mount Stop Light
Outside MouldingBack Door Hingew/ Rear spoiler:
Rear Spoiler
Back Door Hinge
Rear Wiper Arm
Wiper
Motor
Grommet
Rear Wiper
Motor
Service Hole Plug
Outside MouldingStep Liner Back Door Glass Back Door Side
Garnish
Back Door Glass Run
Outer Weatherstrip
Back Door
Glass Guide Rail
Outer Cover
Power Window Regulator
Back Door
Glass Guide RailOutside Handle
Key Cylinder
Rear Light
Lower Stopper Rear Light Opening Hole Cover
Stopper Cushion
Back Door Lock ProtectorControl
Cable
Stopper Cushion
: Specified torque Strap Cover
Back Door Pull StrapBack Door Trim Board Inner WeatherstripNo. 1 Service
Hole Cover
Opening Hole Cover
19.5 (199, 14.4)
8.0 (82, 71 in.´lbf)
5.5 (56, 49 in.´lbf)
5.5 (56, 49 in.´lbf)
8.0 (82, 71 in.´lbf)
N´m (kgf´cm, ft´lbf)No. 2 Service
Hole Cover
Back Door
Handle
Protector
Licence Plate
Light
Assembly
Outside
Garnish
Washer Nozzle
Lower Stopper
Power Window
Regulator Motor
Back Door Lock
19.5 (199, 14.4)
8.0 (82, 71 in.´lbf)
± BODYBACK DOOR
BO±25
3578 Author: Date:
2005 SEQUOIA (RM1146U)
BACK DOOR
COMPONENTS

H16680
H16681
H16682
± BODYBACK DOOR
BO±29
3582 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Employ the same manner described above to the other
side.
16. REMOVE POWER WINDOW REGULATOR
(a) Disconnect the connector.
(b) Disengage the connector and clamp.
(c) Remove the 4 nuts and power window regulator.
Torque: 5.5 N´m (56 kgf´cm, 49 in.´lbf)
HINT:
Remove the power window regulator through the service hole.
(d) Remove the 3 screws and power window regulator motor
from the power window regulator.
(e) Remove the nut and limit switch from the power window
regulator.
HINT:
At the time of reassembly, please refer to following item.
Remove the window regulator gear, then apply MP grease to
the power window regulator.
NOTICE:
At the time of reassembly, please refer to following item.
Do not apply grease to the spring of the power window reg-
ulator.
17. REMOVE REAR WIPER MOTOR
(a) Disconnect the connector.
(b) Disengage the connector and clamp.
(c) Remove the service hole plug.
(d) Unfasten the 3 bolts, then remove the rear wiper motor.
Torque: 5.5 N´m (56 kgf´cm, 49 in.´lbf)
18. REMOVE BACK DOOR LOCK
(a) Remove the back door handle protector.
(b) Disconnect the control cable from the back door outside
handle.

H16683
H16684
5 Clips BO±30
± BODYBACK DOOR
3583 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Using a screwdriver, remove the back door lock protector.
HINT:
Tape the screwdriver tip before use.
(d) Remove the 3 bolts and back door lock.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
19. REMOVE OUTSIDE GARNISH
(a) Remove the 2 service hole plugs.
(b) Remove the 2 nuts.
(c) Using a screwdriver, remove the outside garnish.
HINT:
Tape the screwdriver tip before use.
(d) Remove the 2 screws and outside handle from the out-
side garnish.
(e) Remove the nut and key cylinder from the outside gar-
nish.
(f) Remove the 4 screws and licence plate light assembly
from the outside garnish.
20. w/ Rear spoiler:
REMOVE REAR SPOILER (See page BO±174)
21. w/ o Rear spoiler:
REMOVE HIGH MOUNT STOP LIGHT

BO45V±01
H16685
H16686
H16687
H16688
± BODYBACK DOOR
BO±31
3584 Author: Date:
2005 SEQUOIA (RM1146U)
ADJUSTMENT
1. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Loosen the door side hinge bolts to adjust.
Torque: 19.5 N´m (199 kgf´cm, 14.4 ft´lbf)
2. ADJUST DOOR IN FORWARD/REARWARD AND VER-
TICAL DIRECTIONS
Loosen the body side hinge bolts and nuts to adjust.
Torque: 19.5 N´m (199 kgf´cm, 14.4 ft´lbf)
3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fit and door linkages are adjusted cor-
rectly.
(b) Loosen the striker mounting screws.
Torque: 27 N´m (275.5 kgf´cm, 19.9 ft´lbf)
(c) Using a plastic hammer, tap the striker to adjust.
4. ADJUST LOWER STOPPER
Loosen the stopper mounting bolts to adjust.

BO469±02
H16699
H16700
Adhesive
Tape
H16701
Adhesive
Tape
± BODYBODY OUTSIDE MOULDING
BO±47
3600 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE FRONT FENDER MOULDING
(a) Remove the 3 screws and front mudguard.
(b) Remove the 5 screws.
(c) Using a moulding remover, remove the front fender
moulding.
HINT:
Tape the moulding remover tip before use.
2. REMOVE FRONT DOOR OUTSIDE MOULDING
(a) Apply protective tape to the outer surface as shown in the
illustration, to keep the surface from being scratched.
(b) Using a heat light, heat the moulding to 40±60 °C (104 ±
140 °F)
NOTICE:
Do not heat moulding excessively.
(c) Tie both piano wire ends to wooden blocks or similar ob-
jects.
(d) Cut the adhesive tape by pulling the piano wire.
NOTICE:

If reusing the moulding, take care not to damage the
moulding.

Do not damage the door panel.
(e) Remove the moulding.
3. REMOVE REAR DOOR OUTSIDE MOULDING
(a) Apply protective tape to the outer surface as shown in the
illustration, to keep the surface from being scratched.
(b) Using a heat light, heat the moulding to 40 ± 60 °C (104
± 140 °F)
NOTICE:
Do not heat moulding excessively.
(c) Tie both piano wire ends to wooden blocks or similar ob-
jects.
(d) Cut the adhesive tape by pulling the piano wire.
NOTICE:

If reusing the moulding, take care not to damage the
moulding.

Do not damage the door panel.
(e) Remove the moulding.

H16780
42 (430, 31)
No. 2 Rear Window
Side Garnish
Rear Trim
Rear No. 1 Seat
Outer BeltRear Seat Shoulder
Belt Cover Rear Window
Side Garnish Adjustable Anchor
Rear Door
Opening Trim
Weatherstrip
Rear Door
Scuff PlateRear No. 2 Seat
Outer Belt
Rear Seat
Shoulder
Belt Guide
Rear
Outer BeltRear No. 2 Inner BeltChild Comfort Guide
Rear Seat LockDome Light
Lens
Rear Trim Cover
Rear Floor Mat
Support Plate Rear No. 2 Seat
Outer Center Belt
Quarter Trim
Panel
Rear No. 1
Inner Belt
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
8.5 (87, 76 in.´lbf)
8.5 (87, 76 in.´lbf)
N´m (kgf´cm, ft´lbf) : Specified torque
42 (430, 31)
42 (430, 31)
42 (430, 31)
Front
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
42 (430, 31)
BO±160
± BODYSEAT BELT
3713 Author: Date:
2005 SEQUOIA (RM1146U)

H18975
H18975
H02612
SST SST
R13455
10 m (33 ft) or more BO±168
± BODYSEAT BELT PRETENSIONER
3721 Author: Date:
2005 SEQUOIA (RM1146U)
(5) Disconnect the pretensioner connector as shown in
the illustration.
(6) Buckle the front seat belt and check that there is no
looseness and slack in the front seat inner belt and
front seat outer belt.
(c) Other front seat outer belts:
Disconnect the pretensioner connector.
(1) Remove the front door scuff plate.
(2) Remove the slide door scuff plate.
(3) Remove the center pillar lower garnish.
(4) Disconnect the pretensioner connector as shown in
the illustration.
(5) Buckle the front seat belt and check that there is no
looseness and slack in the front seat inner belt and
front seat outer belt.
(6) Connect the 2 SST each other, then connect them
to the seat belt pretensioner.
SST 09082±00700, 09082±00740
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock secondary lock of the twin lock.
(7) Move the SST to at least 10mm (33 ft) away from the
front of the vehicle.
(8) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(9) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the negative (±) termi-
nal.
(d) Activate seat belt pretensioner.
(1) Confirm that no one is inside the vehicle or within 10
m (33 ft) area around the vehicle.
(2) Press the SST activation switch and activate the
seat belt pretensioner.
HINT:
The seat belt pretensioner operates simultaneously as the LED
of the SST activation switch lights up.
(e) Dispose of the front seat outer belt (with seat belt preten-
sioner).

05_SEQUOIA_U (L/O 0408)
2
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
1. Side vents
2. Instrument cluster
3. Center vents
4. Multi±information display
5. Personal lights
6. Garage door opener box or auxiliary
box
7. Electric moon roof switches
8. Side defroster outlet
9. Glove box
10. Power door lock switches
11. Power window switches
12. Power outlets
13. Seat heater switches
14. Rear console box
15. Rear air conditioning controls
16. Headphone input jacks and headphone
volume control dials
17. Input terminal adapter
18. Cup holders
19. Power rear view mirror control switches
20. Lower vent
Instrument panel overview

View A