2001 TOYOTA SEQUOIA door lock

BO45L±02
H16656
Upper Window Frame Moulding
Door Glass Run
Front Door Weatherstrip
Door Glass
Rear Lower
FrameTweeter Speaker
Lower Frame
Bracket Garnish
No. 2 Glass Run
Front Lower
Frame
Door Belt Moulding
Outside Rear View Mirror No. 2 Front Door
Weatherstrip
Outside Handle
Lock Cylinder
Cable Protector
Door Lock
Door Lock Outer Cover
Window Regular
MotorWindow Regular
Sub±Assembly
Service Hole Cover
Inside Handle
Upper Armrest base panel
Power Window Switch
Speaker
Courtesy Light

Precoated part Inside Handle Bezel Door TrimInner WeatherstripDoor Hinge
Door
Check
Door Hinge
5.0 (51, 44 in.´lbf)
5.0 (51, 44 in.´lbf)
5.5 (56, 49 in.´lbf)
8.0 (82, 71 in.´lbf)
8.0 (82, 71 in.´lbf)
8.0 (82, 71 in.´lbf)
23 (235, 17)
23 (235, 17)
30 (306, 22)
: Specified torque


N´m (kgf´cm, ft´lbf)
± BODYFRONT DOOR
BO±9
3562 Author: Date:
2005 SEQUOIA (RM1146U)
FRONT DOOR
COMPONENTS

H16651
12 3
5
64
H16652
H16653
± BODYFRONT DOOR
BO±13
3566 Author: Date:
2005 SEQUOIA (RM1146U)
(d) Remove the 3 screws and window regulator motor from
the window regulator sub±assembly.
HINT:
At the time of reassembly, please refer to the following items.

Tighten the bolts in the order shown in the illustration.

Apply MP grease to the window regulator assembly.
NOTICE:
At the time of reassembly, please refer to the following
item.
Do not apply grease to the spring of the window regulator
assembly.
18. REMOVE DOOR LOCK
(a) Disengage the 2 control cables from the clamp.
(b) Remove the clamp.
(c) Remove the screw and cable protector.
(d) Disconnect the 2 control links from the outside handle and
lock cylinder.
(e) Disconnect the connector.
(f) Remove the bolt, 3 screws and door lock.
HINT:
Remove the door lock through the service hole.
Torque:
Bolt: 5.0 N´m (51 kgf´cm, 44 in.´lbf)
Screw: 5.0 N´m (51 kgf´cm, 44 in.´lbf)
HINT:

At the time of reassembly, please refer to the following
items.

Apply adhesive to 3 screws.
Part No. 08833±00070, THREE BOND 1324 or equiva-
lent.

H16654
H16655
BO±14
± BODYFRONT DOOR
3567 Author: Date:
2005 SEQUOIA (RM1146U)

Install the door lock as shown in the illustration.
(g) Remove the 2 screws and door lock outer cover from the
door lock.
HINT:
At the time of reassembly, please refer to the following item.
Apply MP grease to the sliding and rotating parts of the door
lock.
19. REMOVE OUTSIDE HANDLE WITH LOCK CYLINDER
(a) Remove the service hole plug.
(b) Remove the 2 bolts and outside handle with lock cylinder.
Torque: 5.5 N´m (56 kgf´cm, 49 in.´lbf)
(c) Remove the bolt and lock cylinder from the outside han-
dle.
Torque: 5.5 N´m (56 kgf´cm, 49 in.´lbf)
20. REMOVE FRONT DOOR WEATHERSTRIP
Using a clip remover, remove the front door weatherstrip.
21. REMOVE NO. 2 FRONT DOOR WEATHERSTRIP

BO45N±01
H16657
H16658
Z06435
± BODYFRONT DOOR
BO±15
3568 Author: Date:
2005 SEQUOIA (RM1146U)
ADJUSTMENT
1. ADJUST DOOR IN FORWARD/REARWARD AND VER-
TICAL DIRECTIONS
Using SST, adjust the door by loosening the body side hinge
bolts.
SST 09812±00010
Torque: 23 N´m (235 kgf´cm, 17 ft´lbf)
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Adjust the door by loosening the door side hinge bolts.
HINT:
Substitute the standard bolt for the centering bolts.
(See page BO±7)
Torque: 23 N´m (235 kgf´cm, 17 ft´lbf)
3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fit and door lock linkages are adjusted
correctly.
(b) Adjust the striker position by slightly loosening the striker
mounting screws, and hitting the striker with a hammer.
(c) Tighten the striker mounting screws again.
Torque: 23 N´m (235 kgf´cm, 17 ft´lbf)

BO45P±01
H16670
Rear Door
Quarter Window GlassUpper Window Frame Moulding
Door Glass Run
Division Bar
Rear Door Weatherstrip
Door Glass Quarter Window
Weatherstrip
Door Lock Striker
Outside Handle
Door Lock Outer Cover
Window Regulator Motor
No. 2 Rear Door
Weatherstrip
Door Hinge
Child Protection Cover
Door Lock
Cable Protection
Door Belt Moulding
Inner Weatherstrip
Door Trim
Courtesy Light Inside Handle BezelSpeaker Upper Armrest Base PanelPower Window SwitchService Hole Cover
Inside Handle
Ash Tray Window Regulator
Sub±assemblyDoor HingeDoor Check

Precoated part: Specified torque
N´m (kgf´cm, ft´lbf)


23 (230, 17)
23 (230, 17)
23 (230, 17)
23 (230, 17)
23 (230, 17)
30 (306, 22)
5.5 (56, 49 in.´lbf)
5.5 (56, 49 in.´lbf)
8.0 (82, 71 in.´lbf)
5.0 (51, 44 in.´lbf)
5.5 (56, 49 in.´lbf)
± BODYREAR DOOR
BO±17
3570 Author: Date:
2005 SEQUOIA (RM1146U)
REAR DOOR
COMPONENTS

H16663
1
3
2 4
4
H16664
H16665
H16666
± BODYREAR DOOR
BO±21
3574 Author: Date:
2005 SEQUOIA (RM1146U)
(d) Remove the 3 screws and window regulator motor from
the window regulator sub±assembly.
HINT:
At the time of reassembly, please refer to the following items.

Tighten the bolts in the order shown in the illustration.

Apply MP grease to the window regulator assembly.
NOTICE:
At the time of reassembly, please refer to the following
item.
Do not apply grease to the spring of the window regulator
assembly.
14. REMOVE DOOR LOCK
(a) Disengage the 2 control cables from the clamp.
(b) Remove the clamp.
(c) Remove the screw and cable protector.
(d) Disconnect the connector.
(e) Remove the bolt, 3 screws and door lock.
HINT:
Remove the door lock through the service hole.
Torque:
Bolt: 5.0 N´m (51 kgf´cm, 44 in.´lbf)
Screw: 5.5 N´m (56 kgf´cm, 49 in.´lbf)

H16667
BO±22
± BODYREAR DOOR
3575 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:

At the time of reassembly, please refer to the following
items.

Apply adhesive to 3 screws.
Part No. 08833±00070, THREE BOND 1324 or equiva-
lent.

Install the door lock as shown in the illustration.
(f) Remove the 2 screws and door lock outer cover from the
door lock.
HINT:
At the time of reassembly, please refer to the following item.
Apply MP grease to the sliding and rotating part of the door lock.
15. REMOVE OUTSIDE HANDLE
Torque: 5.5 N´m (56 kgf´cm, 49 in.´lbf)
16. REMOVE REAR DOOR WEATHERSTRIP
17. REMOVE REAR DOOR OUTSIDE LOWER MOULDING
18. REMOVE NO. 2 REAR DOOR WEATHERSTRIP

BO45R±01
H16668
H16669
BO2556
± BODYREAR DOOR
BO±23
3576 Author: Date:
2005 SEQUOIA (RM1146U)
ADJUSTMENT
1. ADJUST DOOR IN FORWARD/ REARWARD AND VER-
TICAL DIRECTIONS
(a) Remove the front and rear door scuff plates.
(b) Remove the center pillar lower garnish.
(c) Remove the front seat outer belt (See page BO±101).
(d) Loosen the body side hinge nuts to adjust.
Torque: 23 N´m (230 kgf´cm, 17 ft´lbf)
(e) Install the front seat outer belt and center pillar lower gar-
nish (See page BO±101).
(f) Install the front and rear door scuff plates.
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Loosen the door side hinge bolts to adjust.
Torque: 23 N´m (230 kgf´cm, 17 ft´lbf)
3. ADJUST DOOR LOCK STRIKER
(a) Check that the door fit and door lock linkages are adjusted
correctly.
(b) Loosen the striker mounting screws to adjust.
Torque: 23 N´m (230 kgf´cm, 17 ft´lbf)
(c) Using a plastic hammer, tap the striker to adjust it.