2001 TOYOTA SEQUOIA lights

A21044
Engine
Room
R/BR±B
7ECM
W
E4 11
C8
C10 12
B
R±L15 2
2
Battery7
6I18
Ignition
Switch
41D
1G 6
B±R R
GAUGE
Combination
Meter Malfunction
Indicator
Lamp AM2
IG2 AM2
DI±512
± DIAGNOSTICSENGINE
706 Author: Date:
2005 SEQUOIA (RM1146U)
MIL Circuit
CIRCUIT DESCRIPTION
If the ECM detects a trouble, the MIL lights up. At this time, the ECM records a DTC in the memory.
WIRING DIAGRAM
DICFG±02

DI±514
± DIAGNOSTICSENGINE
708 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check that MIL lights up.
CHECK:
Check that MIL lights up when turning the ignition switch ON.
OK:
Standard: MIL lights up
OK System OK.
NG
4 Inspect combination meter assy (MIL circuit).
See the combination meter troubleshooting on page BE±55.
NG Repair or replace bulb or combination meter as-
sembly.
OK
Check and repair harness and connector be-
tween combination meter and ECM.

DIDIK±01
D13871
Combination Meter
DLC3 Stop Light SwitchECM
Park/Neutral Position SwitchSpeed Sensor (SP2) Shift Solenoid Valve S1
Shift Solenoid Valve SR
Shift Solenoid Valve SLU
Shift Solenoid Valve SL2 ATF Temperature
Sensor No. 2Integration Control and Panel
(Shift Position L Switch)
MIL
Shift Solenoid Valve SL1
Shift Solenoid
Valve SLT
ATF Temperature
Sensor No.1
Shift Solenoid Valve S2
Speed Sensor (NT)

AT Oil Temp Warning LightShift Lever
(O/D Main Switch)
4WD:
4WD Control ECU
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±519
713 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

DIDJ4±01
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±573
767 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the parts listed in the table below and proceed to the page
given.
HINT:
*1 :
... The MIL (Malfunction Indicator Lamp) lights up
*2 :  ... The ECM memorizes the trouble code if the ECM detects the DTC detection condition.
This DTC may be output when the clutch, brake and gear components etc. inside the automatic trans-
mission are damaged.
DTC No.
(See Page)Detection ItemTrouble AreaMIL *1Memory *2
P0500
(DI±278)Vehicle Speed Sensor ºAº
Open or short in speed sensor (SP2) circuit
Speed sensor (SP2)
ECM


P0705
(DI±576)Transmission Range Sensor Cir-
cuit Malfunction (PRNDL Input)Open or short in park/neutral position switch circuit
Park/neutral position switch
ECM


P0710
(DI±582)Transmission Fluid Temperature
Sensor ºAº CircuitOpen or short in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0711
(DI±588)Transmission Fluid Temperature
Sensor ºAº PerformanceTransmission wire (ATF temperature sensor No.1)

P0712
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit Low InputShort in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0713
(DI±582)Transmission Fluid Temperature
Sensor ºAº Circuit High InputOpen in ATF temperature sensor No.1 circuit
Transmission wire (ATF temperature sensor No.1)
ECM


P0717
(DI±591)Input Speed Sensor Circuit No
Signal
Open or short in speed sensor (NT) circuit
Speed sensor (NT)
ECM
Automatic transmission (clutch, brake or gear, etc.)


P0722
(DI±596)Output Speed Sensor Circuit No
Signal
Open or short in speed sensor (SP2) circuit
Speed sensor (SP2)
ECM
Automatic transmission (clutch, brake or gear, etc.)


P0724
(DI±600)Brake Switch ºBº Circuit High
Short in stop light switch signal circuit
Stop light switch
ECM


P0748
(DI±603)Pressure Control Solenoid ºAº
Electrical
(Shift Solenoid Valve SL1)Open or short in shift solenoid valve SL1 circuit
Shift solenoid valve SL1
ECM


P0751
(DI±608)Shift Solenoid ºAº Performance
(Shift Solenoid Valve S1)Shift solenoid valve S1 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P0756
(DI±614)Shift Solenoid ºBº Performance
(Shift Solenoid Valve S2)Shift solenoid valve S2 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)


P0771
(DI±620)Shift Solenoid ºEº Performance
(Shift Solenoid Valve SR)
Shift solenoid valve SR remains open or closed
Shift solenoid valve SL1 remains open or closed
Valve body is blocked
Automatic transmission (clutch, brake or gear, etc.)



DIDLX±01
DI±894
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1088 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
1. SYSTEM DESCRIPTION
HINT:

The yaw rate sensor and deceleration sensor are combined and in a single unit. This unit communi-
cates with the skid control ECU through the CAN communication system.

No changes have been made to the communication method between the VSC system and ECM. How-
ever, the communication method between the Translate ECU and ECM has been changed from serial
to CAN communication.
(a) ABS
(Anti±lock Brake System)
The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking
on a slippery surface.
(b) EBD
(Electronic Brake force Distribution)
The EBD control utilizes ABS, realizing proper brake force distribution between front and rear wheels
in accordance with driving conditions.
In addition, during braking while cornering, it also controls the brake forces of the right and left wheels,
helping to maintain vehicle behavior.
(c) BA (Brake Assist)
The primary purpose of the brake assist system is to provide an auxiliary brake force to assist the driver
who cannot generate a large enough brake force during emergency braking, thus helping to maximize
the vehicle's braking performance.
(d) TRAC
(Traction Control)
The TRAC system helps prevent the drive wheels from slipping if the driver presses down on the accel-
erator pedal excessively when starting off or accelerating on a slippery surface.
(e) VSC
(Vehicle Stability Control)
The VSC system helps prevent the vehicle from slipping sideways as a result of strong front wheel skid
or strong rear wheel skid during cornering.
2. ABS with EBD & BA & TRAC & VSC OPERATION
(a) The skid control ECU calculates vehicle stability tendency based on signals from the speed sensor,
yaw rate (deceleration) sensor and steering angle sensor. In addition, it evaluates the results of the
calculations to determine whether any control actions (control of the engine output torque by electronic
throttle control and of the wheel brake pressure by the brake actuator) should be implemented.
(b) The SLIP indicator blinks and the VSC buzzer sounds to inform the driver that the VSC system is oper-
ating. The SLIP indicator also blinks when TRAC is operating, and the operation being performed is
displayed.
3. FAIL SAFE FUNCTION
(a) When a failure occurs in the ABS & BA & TRAC & VSC systems, the ABS and VSC warning lights come
on and ABS & BA & TRAC & VSC operations are prohibited. In addition to this, when there is a failure
that disables EBD operation, the brake warning light also comes on and EBD operation is prohibited.
(b) If some control is prohibited due to a malfunction during its operation, that control will be cut off gradual-
ly not to change the stability of the vehicle suddenly.

DIDLZ±01
F09750
DLC3Ts
CG
BR3904
0.13 sec. 0.13 sec.
ON
OFF
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±899
1093 Author: Date:
2005 SEQUOIA (RM1146U)
TEST MODE PROCEDURE
1. When not using the hand±held tester:
SENSOR CHECK (TEST MODE)
NOTICE:
When having replaced the master cylinder pressure, yaw
rate and deceleration sensors and/or the ECU, perform
zero point calibration of the master cylinder pressure, yaw
rate and deceleration sensors (See page DI±897).
HINT:
If the ignition switch is turned from the ON to the ACC or LOCK
position in test mode, test mode DTCs will be erased.
(a) Procedures for test mode:
(1) Turn the ignition switch OFF.
(2) Check that the shift lever is in the P position, and
turn the steering wheel to the neutral position.
(3) Using SST, connect terminals Ts and CG of the
DLC3.
SST 09843±18040
(4) Start the engine.
(5) Check that the ABS and VSC TRAC warning lights
blink.
HINT:
If the ABS and VSC TRAC warning lights do not blink, inspect
the ABS warning light circuit, VSC TRAC warning light circuit
and Ts terminal circuit.
(6) Keep the vehicle in a stationary condition on a level
surface for 4 sec. or more.
ABS warning light circuitDI±1021 or DI±1025
VSC TRAC warning light circuitDI±1027 or DI±1031
Ts terminal circuitDI±1057

D05981
Hand±held
Tester
DLC3
BR3904
0.13 sec. 0.13 sec.
ON
OFF
F02135
Start Position
End PositionWithin ± 5° DI±902
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1096 Author: Date:
2005 SEQUOIA (RM1146U)
2. When using the hand±held tester:
SENSOR CHECK (TEST MODE)
NOTICE:
When having replaced the master cylinder pressure, yaw
rate and deceleration sensors and/or ECU, perform zero
point calibration of the master cylinder pressure, yaw rate
and deceleration sensors (See page DI±897). Make sure
that this operation is done before performing the following.
(a) Procedures for test mode:
(1) Connect the hand±held tester to the DLC3.
(2) Check that the shift lever is in the P position, and
turn the steering wheel to the neutral position.
(3) Start the engine.
(4) Select the SIGNAL CHECK on the hand±held tes-
ter.
(5) Check that the ABS warning light and VSC TRAC
warning light blink.
HINT:
If the ABS and VSC TRAC warning lights do not blink, inspect
the ABS warning light circuit, VSC TRAC warning light circuit
and Ts terminal circuit.
(6) Keep the vehicle in a stationary condition on a level
surface for 4 sec. or more.
ABS warning light circuitDI±1021 or DI±1025
VSC TRAC warning light circuitDI±1027 or DI±1031
Ts terminal circuitDI±1057
(b) Check the yaw rate and deceleration sensor.
Shift the shift lever to the D position and drive the vehicle
at a vehicle speed of approx. 3 mph (5 km/h), turn the
steering wheel either to the left or right for 90° or more,
and turn the vehicle through 180 degrees. Check that the
VSC buzzer sounds for 3 seconds upon start off.
Stop the vehicle and shift the shift lever to the P position,
check that the VSC buzzer sounds again for 3 seconds.

DIDM1±01
F13444
USA: CANADA:USA: CANADA:2WD: 4WD:
DI±910
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1104 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSIS SYSTEM
1. CHECK WARNING LIGHT
(a) Release the parking brake pedal.
(b) When the ignition switch is turned ON, check that the ABS
warning light, VSC TRAC warning light, VSC OFF (TRAC
OFF) indicator light, BRAKE warning light and SLIP indi-
cator light come on for approx. 3 seconds.
HINT:

When the parking brake is applied or the level of the brake
fluid is low, the BRAKE warning light comes on.

If the indicator check result is not normal, proceed to trou-
bleshooting for the ABS warning light circuit, VSC TRAC
warning light circuit, VSC OFF (TRAC OFF) indicator light
circuit, BRAKE warning light circuit or SLIP indicator light
circuit.
Trouble AreaSee page
ABS warning light circuitDI±1021 or
DI±1025
VSC TRAC warning light circuitDI±1027 or
DI±1031
VSC OFF (TRAC OFF) indicator light circuitDI±1048
BRAKE warning light circuitDI±1033 or
DI±1038
SLIP indicator light circuitDI±1041 or
DI±1045

The DTCs are simultaneously stored in the memory. The
DTCs can be read by connecting the SST between TC
and CG terminals of the DLC3 and observing the blinking
of the ABS and VSC warning lights, or by connecting a
hand±held tester.

This system has a sensor signal check function (TEST
MODE) (See page DI±899).
The DTC can be read by connecting the SST between ter-
minals TS and CG of the DLC3 and observing the blinking
of the ABS and VSC TRAC warning lights, or by connect-
ing a hand±held tester.