2001 TOYOTA SEQUOIA ECO mode

I03487
GARAGE DOOR
OPENER SWITCH
LEARN MODE
INDICATOR
OPERATION
ORIGINAL
TRANSMITTERPRESSED
ENTER
EXIT
ON
OFF20 sec.
INDICATOR flashes
at a rate of 1 Hz
INDICATOR
flashes at a
rate of 5.6 Hz RELEASED
ON
OFF BE±130
± BODY ELECTRICALGARAGE DOOR OPENER SYSTEM
3534 Author: Date:
2005 SEQUOIA (RM1146U)
New code registration timing chart
If a code can not be registered, observe the following condi-
tions.
HINT:

If the battery of original transmitter is consumed.

Press the switch of the transmitter repeatedly in registra-
tion mode, as some transmitters stop transmitting for 1 to
2 seconds.

This system is not applicable to the garage door opener
which had been made before 1982.
2. CODE DELETION
(a) Press the switches at both ends of the garage door open-
er simultaneously for 20 seconds.
HINT:
When transferring to deletion mode, garage door indicator
(green) blinks in 6 Hz cycle.
(b) When releasing the switch within 10 seconds after trans-
ferring to deletion mode, all the registered codes will be
erased.
HINT:
Press the switch until 6 Hz cycle blinking stops, so that the de-
fault code for check is set.

START
Insert the key in the key cylinder.
Under registration
Registration completion
Remove the key.
Will you register the
next key?
NoSecurity indicator blinks until the first
key is inserted. The indicator comes
on after the key registration.
Security Indicator
OFF
END Ye s
Security Indicator ON
(After the last key (sub±key) has been
registered, the indicator remains OFF
until the key is removed. After the key
is removed, the indicator blinks.)
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE±137
3541 Author: Date:
2005 SEQUOIA (RM1146U)
ENGINE IMMOBILISER SYSTEM
REGISTRATION PROCEDURE
HINT:
If you lose all the registered master keys, you cannot registrar or delete additionally. Change the transponder
key ECU and then register the new key codes following the registration procedure of the automatic registra-
tion mode below.
1. KEY REGISTRATION IN AUTOMATIC REGISTRATION MODE
(a) Registration of a new transponder key.
HINT:

This procedure must be done when you install a new transponder key ECU.

The new transponder key ECU is in automatic key code registration mode. The key codes already fixed
for this transponder key ECU can be registered.
For this type of vehicle, up to 3 key codes can be registered.

In the automatic registration mode, the last key registered becomes a sub±key.

BE±140
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
3544 Author: Date:
2005 SEQUOIA (RM1146U)
*1: Insert the master key into the key cylinder.
Turn the ignition switch to the LOCK " ON position 5 times within 15 seconds.
*2: Open and close the driver's door 6 times within 20 seconds after completion of the previous operation.
*3: Remove the master key from the ignition switch and insert another key to be registered in the key cylinder
within 10 seconds after completion of the previous operation.
*4: Turn the ignition switch to the ON position and wait for 60 seconds or more, then key registration will be
completed.
*5: 10 seconds or more elapse after removal of the key or open and close the driver's door, then key registra-
tion will be completed.
*6: When registering multiple keys, insert the key to be registered in the key cylinder.
HINT:

It is possible to register up to 4 master key codes including the registered key code.

It is possible to register up to 2 sub key codes including the registed key code.

When any operation time described above is over, registration mode completes.

When the next procedure is performed while the timer is working, the timer completes counting time,
then the next timer starts.

Insert the master key in the key cylinder.
Driver's door: Open " Close 7 times Ignition switch: LOCK " ON 6 times
Remove the master key.START
END
*1
*2within
15 secs.
within
20 secs.
All doors closed. No key in the key cylinder.
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE±141
3545 Author: Date:
2005 SEQUOIA (RM1146U)
3. ERASURE OF TRANSPONDER KEY CODE
Do this operation to erase transponder key registration from the transponder key computer.
HINT:
Delete all other master and sub±key codes leaving the master key code to use the operation. When using
the key which was used before deletion, it is necessary to register the code again.
*1: Insert the master cylinder into the key cylinder.
Turn the ignition switch to LOCK " ON 6 times within 15 seconds.
*2: Open and close driver's door 7 times and remove the master key within 20 seconds after completion of
the previous operation.
HINT:

When any operation time described above is over, registration mode completes.

When the next procedure is performed while the timer is working, the timer completes counting time,
then the next timer starts.
4. ECU COMMUNICATION ID REGISTRATION
NOTICE:

The ECU communication ID should be registered when the transponder key ECU and/or the
ECM is replaced, in order to match these ECM COMMUNICATION ID.

The engine cannot be started unless the ECM COMMUNICATION ID matches.
(a) Register the ECU communication ID.
(1) After the transponder key ECU and/or the ECM is replaced, turn the ignition switch ON (the en-
gine is not running).
(2) Short the Tc and CG terminals of the DLC3 and leave it as it is for 30 minutes.
(3) Check that the engine starts.

05_SEQUOIA_U (L/O 0408)
18
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
1. ªLOCKº switch
2. ªUNLOCKº switch
3. Back window open switch
4. ªPANICº switchThe wireless remote control system is
designed to lock or unlock all the side
doors and back door, open the back
window or activate the ªPANICº mode
from a distance within approximately 1
m (3 ft.) of the vehicle.
When you operate any switch, push it
slowly and securely.
The wireless remote control transmitter is
an electronic component. Observe the fol-
lowing instructions in order not to cause
damage to the transmitter.

Do not leave the transmitter in places
where the temperature becomes high
such as on the dashboard.

Do not disassemble it.

Avoid knocking it hard against other
objects or dropping it.

Avoid putting it in water.
You can use up to 4 wireless remote con-
trol transmitters for the same vehicle.
Contact your Toyota dealer for detailed
information.If the wireless remote control transmitter
does not actuate the doors or alarm, or
operate from a normal distance:

Check for closeness to a radio trans-
mitter such as a radio station or an
airport which can interfere with normal
operation of the transmitter.

The battery may have been consumed.
Check the battery in the transmitter. To
replace the battery, see ªÐReplacing
batteryº on page 23.
If you lose your transmitter, contact your
Toyota dealer as soon as possible to
avoid the possibility of theft, or an acci-
dent. (See ªIf you lose your wireless re-
mote control transmitterº on page 402 in
Section 4.)
Wireless remote controlÐ

05_SEQUOIA_U (L/O 0408)
22
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
To open the back window, push the
back window open switch of the trans-
mitter for about 1 second. The window
will fully open.
At this time, you can hear a beep.
If the ignition switch is in the ªONº posi-
tion, the back window cannot be opened
by the back window open switch.
To open the back window with the master
key, see ªPower back windowº on page 31
in this Section.
The back window opening program by
wireless remote control can be changed or
disabled. For details, contact your Toyota
dealer.Pushing the ªPANICº switch blows the
horn intermittently and flashes the
headlights and tail lights.
The ªPANICº switch is used to deter ve-
hicle theft when you witness anyone at-
tempting to break into or damage your
vehicle.
The alarm will last for one minute. To stop
alarm midway, push the ªPANICº or
ªUNLOCKº switch, or unlock any side door
or back door with key. You can also stop
the alarm by turning the ignition key from
ªLOCKº to the ªONº position.The ªPANICº mode does not work when
the ignition key is in the ªONº position.
This alarm function can be disabled. For
details, contact your Toyota dealer.
ÐOpening back window ÐActivating panic mode

05_SEQUOIA_U (L/O 0408)
36
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
To open the hood:
1. Pull the hood lock release lever. The
hood will spring up slightly.
CAUTION
Before driving, be sure that the hood
is closed and securely locked. Other-
wise, the hood may open unexpected-
ly while driving and an accident may
occur.
2. In front of the vehicle, pull up the
auxiliary catch lever and lift the
hood.
Before closing the hood, check to see that
you have not forgotten any tools, rags,
etc. Then lower the hood make sure it
locks into place. If necessary, press down
gently on the front edge to lock it.To deter vehicle theft, the system is
designed to sound an alarm if any of
the side doors, back door or hood is
forcibly unlocked or opened or the bat-
tery terminal is disconnected and then
reconnected when the vehicle is locked.
On some models, the alarm also
sounds, when someone attempts to
break the side windows.
The alarm blows the horn intermittently
and flashes the headlights and tail lights.
HoodTheft deterrent system

05_SEQUOIA_U (L/O 0408)
37
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
Indicator light
Glass breakage sensor (on some models)
SETTING THE SYSTEM
1. Turn the ignition key to the ªLOCKº
position and remove it.
The indicator light will start flashing when
the key is removed from the ignition
switch. (See ªEngine immobilizer systemº
on page 16 in this Section for details.)
2. Have all passengers get out of the
vehicle.
3. Close and lock all the side doors, back
door and hood.
The indicator light will remain on when all
the side doors, back door and hood are
closed and locked.
The system will automatically be set after
30 seconds. When the system is set, the
indicator light will start flashing again.
4. After making sure the indicator light
starts flashing, you may leave the ve-
hicle.
Never leave anyone in the vehicle when
you set the system, because unlocking
from the inside will activate the system.WHEN THE SYSTEM IS SET
Activating the system
The system will sound the alarm under
the following conditions:

If any of the side doors is unlocked or
opened without the key or wireless re-
mote control transmitter, or if the back
door or hood is forcibly opened

If the battery terminal is disconnected
and then reconnected
Vehicles with the glass breakage sensorÐ

The side windows are tapped or bro-
ken.
The indicator light will come on when the
system is activated.
If the alarm has been activated and the
key is not in the ignition switch, all the
side doors and back door will re±lock au-
tomatically.
After one minute, the alarm will automati-
cally stop and the indicator light will starts
flashing again.