2001 TOYOTA SEQUOIA ECO mode

TOYOTA
Hand±held
Tester
D05981DLC3
BR1NG±05
BR±48
± BRAKEABS & VSC ACTUATOR
3215 Author: Date:
2005 SEQUOIA (RM1146U)
ABS & VSC ACTUATOR
ON±VEHICLE INSPECTION
1. CONNECT TOYOTA HAND±HELD TESTER:
(a) Connect the TOYOTA hand±held tester to the DLC3.
(b) Start the engine and run it at idle.
(c) Select the ACTIVE TEST mode on the TOYOTA hand±
held tester.
HINT:
Please refer to the TOYOTA hand±held tester operator's manu-
al for further details.
2. INSPECT ACTUATOR MOTOR OPERATION
(a) With the motor relay ON, check the actuator motor opera-
tion noise.
(b) Turn the motor relay OFF.
(c) Depress the brake pedal and hold it for about 15 seconds.
Check that the pedal does not go down any further while
holding.
(d) With the motor relay ON, check that the pedal does not
pulsate.
NOTICE:
Do not keep motor relay ON for more than 5 seconds con-
tinuously. When operating it continuously, set the interval
of more than 20 seconds.
(e) Turn the motor relay OFF and release the brake pedal.
3. INSPECT RIGHT FRONT WHEEL OPERATION
NOTICE:
Never turn ON the solenoid which is not described below.
(a) With the brake pedal depressed, perform the following
operations.
(b) Turn the SFRH and SFRR solenoid ON simultaneously,
and check that the pedal cannot be depressed.
NOTICE:
Do not keep solenoid ON for more than 10 seconds contin-
uously. When operating it continuously, set the interval of
more than 20 seconds.
(c) Turn the SFRH and SFRR solenoid OFF simultaneously,
and check that the pedal can be depressed.
(d) Turn the motor relay ON and check that the pedal returns.
NOTICE:
Do not keep motor relay ON for more than 5 seconds con-
tinuously. When operating it continuously, set the interval
of more than 20 seconds.
(e) Turn the motor relay OFF and release the brake pedal.
4. INSPECT OTHER WHEEL OPERATION
As in the same procedure, check the solenoids of other wheels.
HINT:
Left front wheel: SFLH, SFLR
Right rear wheel: SRRH, SRRR
Left rear wheel: SRLH, SRLR

± BODY ELECTRICALCOMBINATION METER
BE±59
3463 Author: Date:
2005 SEQUOIA (RM1146U)
15. INSPECT DRIVER'S SEAT BELT WARNING BUZZER
(a) Check warning buzzer function.
(1) Turn the ignition switch ON and check that the driver's seat belt warning buzzer sounds if the
driver 's seat belt is not fastened.
(2) Check that the buzzer stops after about 6 seconds.
16. INSPECT KEY REMINDER WARNING BUZZER
(a) Check warning buzzer function.
(1) Turn the ignition switch OFF and check that the key reminder warning buzzer sounds if the igni-
tion key is inserted into the key cylinder and the front driver side door is opened.
17. MAINTENANCE LIQUID RESETTING PROCEDURE
Indicator Condition:
StateConditionSpecified State
BlinkingThe vehicle has traveled 4,500 miles after the
previous settingThe indicator blinks for 12 seconds after the igni-
tion switch is turned on (including 3 seconds for a
valve check).
Continuously IlluminatedThe vehicle has traveled 5,000 miles after the
previous settingThe indicator is continuously illuminated after the
ignition switch is turned on.
(a) Set the display window to ODO.
(b) Turn the ignition switch off.
(c) Pressing the reset switch, turn the ignition switch to the ON position (keep pressing for at least 5 se-
conds).
(d) Reset procedure is completed.
HINT:

If the ignition switch is turned off during the reset procedure, reset mode is canceled.

If the reset switch is turned off during the reset procedure, reset mode is canceled and the display
shows the condition prior to the reset procedure.

BE2MQ±01
Press E/M and Mode Switches
at the same time.
On Duration
Normal Mode
Pressed for 5 sec.
6. Zone Setting ModeIgnition switch ON.
Pressed for 10 sec.
Zone area +1 E/M Switch ON
7. Calibration Mode
Leaving it untouched
for a while
Normal Mode
± BODY ELECTRICALCOMPASS
BE±61
3465 Author: Date:
2005 SEQUOIA (RM1146U)
CALIBRATION
1. SELECTING COMPASS DISPLAY MODE
The mode select switch allows you to select a Display or Non±display mode of the compass.
2. SETTING ZONE
Deviation between the magnetic north and ºactual northº differs depending on the terrestrial location, there-
fore, an adjustment in magnetism is required. Since the magnetic condition differs according to the area
where the vehicle will be used, it is necessary for each user to set the zone. (Refer to ºCompass Zone Mapº).
The zone setting can be changed using the E/M switch of the display.
3. PERFORMING CALIBRATION
Because each vehicle has its own magnetic field, calibration should be performed for each vehicle. This com-
pass function is used when storing the record of the vehicle's magnetic field.
4. WHEN COMPASS MAGNETIZED:
A compass could be magnetized during shipping by vessels or freight cars. Before delivery, therefore, make
sure to perform calibration and ensure that calibration can be done. If it cannot be done (cannot complete
in spite of driving round several times), it may be caused by magnetization. Demagnetize the vehicle using
a demagnetizer and perform calibration again.
5. SETTING COMPASS

± BODY ELECTRICALCOMPASS
BE±63
3467 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:
In the initial status, º8º is displayed.
(c) The displayed number increases +1 every time the E/M switch is pressed. Referring to the map, check
the number for the area where the vehicle will be used and set the zone number.
(d) Leave it untouched for several seconds after setting and check that the compass display shows an
azimuthal direction (N, NE, E, SE, S, SW, W, or NW) or ºVARº.
7. CALIBRATION SETTING MODE
(a) After the set zone is displayed, if the E/M switch and MODE switch remains pressed for another 5 se-
conds, calibration setting mode will be activated.
(b) Keep pressing the E/M switch and MODE switch for 10 sec. when outer temperature is displayed will
also activate this mode.
(c) Drive the vehicle at a speed of 5 MPH (8 km/h) or less in a circle.
(d) Driving in a circle 1 to 3 times will display the azimuthal direction on the display, completing the calibra-
tion.
HINT:
Once calibration is completed, it is not necessary to perform the above procedures unless the magnetic field
strength is drastically changed. If this happens, the azimuthal display will be changed to ºCALº.

BE2ML±01
BE±82
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
3486 Author: Date:
2005 SEQUOIA (RM1146U)
THEFT DETERRENT SYSTEM
ON±VEHICLE INSPECTION
1. OUTLINE OF THEFT DETERRENT SYSTEM
When the theft deterrent system detects any theft, it informs
people around by flashing lights and sound.
All initial settings are performed in active mode. It can be
switched to passive mode by using the hand±held tester. (See
step 3. CHANGING METHOD OF PASSIVE MODE.)
HINT:
There are 4 conditions in this system: disarmed state, arming
preparation, armed state and alarm sounding.
(1) Disarmed state
Alarm function does not operate.
Theft deterrent function is not performed.
(2) Arming preparation
Time until transferring to armed state.
Theft deterrent function is not performed.
(3) Armed state
Theft deterrent function is ready.
(4) Alarm sounding:
When the system detects a theft, it informs people
around the vehicle using light and sound.
Refer to the table below for alarming method or
time.
Horn
Security horn
Alarm methodHeadlightAlarm method
Taillight
Interior light
Alarm time60 seconds
Alarm outputContinuous 0.4 secs. (ON)
0.4 secs. (OFF)
HINT:
Alarm output for the hazard is the same as the one for the haz-
ard on the vehicle.
If any of the doors is unlocked not by the key or wireless remote
control in the armed state, a force lock signal will be output.

Disarmed state
Perform any of the following and the system will go on to ºArming preparationº:

With all the doors, the engine hood and the back door closed, lock all doors with the key.

With all the doors, the engine hood and the back door closed, lock all doors by the
wireless remote control.

With all the doors, engine hood and back door locked, open and close any of the doors, the
engine hood or the back door, then close and lock all doors, the engine hood and the back door.
Arming preparation
Perform the following and the system will
go on to ºArmed stateº:

Let 30 seconds elapse with all the doors,
engine hood and the back door closed and
locked.
Perform any of the following and the system
will return to ºDisarmed stateº:

Open any of the doors, the engine hood or
the back door .

Unlock any of the doors or the back door.

Put the key in the key cylinder.

Reconnect the battery.
Armed state
Perform any of the following and the system
will return to ºDisarmed stateº:

Unlock any of the doors or the back door by
the wireless remote control.

Unlock any of the doors or the back door with
the key.

Put the key in the key cylinder and turn it ON.
Perform any of the following and the system
will go on to ºAlarm soundingº:

Open any of the doors or the back door.

Unlock any of the doors or the back door in
any way other than with a key or by the wireless
remote control.

Open the engine hood.

Reconnect the battery.

When input from the optional glass break sensor
is detected (Dealer option).(Key not inserted in key cylinder.)
Alarm sounding
The vehicle's horn and security horn will sound,
and the hazard, interior, tail and head lights come
on for 60 seconds.
After the alarm has stopped, the system will
return to ºArmed stateº. Perform any of the following and the system
will return to ºDisarmed stateº:

Unlock any of the doors and the back door by
the wireless remote control.

Unlock any of the doors or the back door with
the key.

Put the key in the key cylinder and turn it ON.
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±83
3487 Author: Date:
2005 SEQUOIA (RM1146U)
2. ACTIVE ARMING MODE

Perform any of the following and the system will go to disarmed state (B):

Turn the key from IG to OFF and remove the key from the ignition, open the driver's door.
Disarmed state (A)
Perform any of the following and the system
will return to disarmed state (A):

Push the unlock switch on the transmitter.

Put the key in the key cylinder.

Reconnect the battery.

Turn the ignition from OFF to ON.

Unlock any of the doors or back door with
the key.Disarmed state (B)Perform the following and the system will go
to arming preparation:

Close all the doors, hood and
back door.
Perform any of the following
and the system
will return to disarmed state
(B):

Open any of the doors, the
hood or the back door.
Arming preparation
Perform the following and the
system will go to armed state:

Allow 30 seconds to elapse
with all the doors, hood and
back door closed.
Perform any of the following and
the system
will return to disarmed state (A):

Push the unlock switch on the
transmitter.

Put the key in the ignition.

Reconnect the battery.

Turn the ignition from OFF to
ON.

Unlock any of the doors or back
door with the key.
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±85
3489 Author: Date:
2005 SEQUOIA (RM1146U)
3. PASSIVE ARMING MODE
This mode can be switched by the C±BEST customizing
function (See page DI±1684).
All modes are initially set to active when shipped from fac-
tory (no passive mode).

Door
Indicator
Alarming output
System condition
Armed state Alarm
sounding Entry delay time Close
Open
ON
OFF
ON
OFF
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±87
3491 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:
If any door is opened in the armed state, entry delay will occur
for 14 seconds.
During this time, the mode transfers to disarmed state if the
condition * is met.
When the condition is not met, the system judges that theft oc-
curs and transfers to the alarm sounding state.