2001 TOYOTA SEQUOIA ECU

DIDIK±01
D13871
Combination Meter
DLC3 Stop Light SwitchECM
Park/Neutral Position SwitchSpeed Sensor (SP2) Shift Solenoid Valve S1
Shift Solenoid Valve SR
Shift Solenoid Valve SLU
Shift Solenoid Valve SL2 ATF Temperature
Sensor No. 2Integration Control and Panel
(Shift Position L Switch)
MIL
Shift Solenoid Valve SL1
Shift Solenoid
Valve SLT
ATF Temperature
Sensor No.1
Shift Solenoid Valve S2
Speed Sensor (NT)

AT Oil Temp Warning LightShift Lever
(O/D Main Switch)
4WD:
4WD Control ECU
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±519
713 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

DIDIL±01
D14205
Shift Solenoid Valve S1
MIL
(Malfunction Indicator Lamp) S1
S2
SL1
SL2
SLT
SLU
SR
WShift Solenoid Valve S2
Shift Solenoid Valve SL1
Shift Solenoid Valve SL2
Shift Solenoid Valve SLT
Shift Solenoid Valve SLU
Shift Solenoid Valve SR
OILW
AT Oil Temp Warning Light ECM Crankshaft Position Sensor
Engine CoolantTemperature Sensor
Combination Meter
Stop Lamp Switch Assy
DLC3
(Data Link Connector 3)THW VTA1, 2
VC
SPD
STPTH01
TC Throttle Position Sensor
ATF (Automatic Transmission
Fluid) Temperature Sensor No. 1Mass Air Flow Meter
Accelerator Pedal Position SensorVPA
VPA2
Shift Lever
(O/D Main Switch)
Input Speed Sensor (NT)NT
Output Speed Sensor (SP2)SP2
TH02
ATF (Automatic Transmission
Fluid) Temperature Sensor No. 2Skid Control ECUNSW
Park/Neutral Position Switch
R, D, 3, 2
VG
NE
L
ODMSIntegration Control and Panel
(Shift Position L Switch)
L4



: 4WD4WD Control ECU
CAN DI±520
± DIAGNOSTICSAUTOMATIC TRANSMISSION
714 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM
The configuration of the electronic control system in the A750E/A750F automatic transmission is as shown
in the following chart.

DIDIZ±01
D14150
D13872DLC3
OBD II Scan Tool
(Hand±held Tester)
CAN VIM
D14151
DLC3
1314 1516 12 11 10 9 12345678 DI±562
± DIAGNOSTICSAUTOMATIC TRANSMISSION
756 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSIS SYSTEM
DESCRIPTION
When troubleshooting On±Board Diagnostic (OBD II) vehicles,
the vehicle must be connected to the OBD II scan tool (comply-
ing with SAE J1987). Various data output from the vehicle's
ECM can then be read.
OBD II regulations require that the vehicle's on±board comput-
er illuminates the Malfunction Indicator Lamp (MIL) on the
instrument panel when the computer detects a malfunction in:
1) The emission control system/components
2) The powertrain control components (which affect vehicle
emissions)
3) The computer
In addition, the applicable Diagnostic Trouble Codes (DTCs)
prescribed by SAE J2012 are recorded in the ECM memory.
If the malfunction does not reoccur in 3 consecutive trips, the
MIL turns off automatically but the DTCs remain recorded in the
ECM memory.
To check DTCs, connect the scan tool to the Data Link Connec-
tor 3 (DLC3) of the vehicle. The scan tool displays DTCs, the
freeze frame data and a variety of the engine data.
The DTCs and freeze frame data can be erased with the scan
tool (See page DI±565).
NORMAL MODE AND CHECK MODE
The diagnosis system operates in ºnormal modeº during normal
vehicle use. In normal mode, º2±trip detection logicº is used to
ensure accurate detection of malfunctions. ºCheck modeº is
also available to technicians as an option. In check mode,
º1±trip detection logicº is used for simulating malfunction symp-
toms and increasing the system's ability to detect malfunctions,
including intermittent malfunctions.
2±TRIP DETECTION LOGIC
When a malfunction is first detected, the malfunction is tempo-
rarily stored in the ECM memory (1st trip). If the ignition switch
is turned OFF and then ON again, and the same malfunction is
detected again, the MIL will illuminate.

DIDJ0±01
D13872DLC3
OBD II Scan Tool
(Hand±held Tester)
CAN VIM
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±565
759 Author: Date:
2005 SEQUOIA (RM1146U)
DTC CHECK / CLEAR
1. CHECK DTC
DTCs which are stored in the ECM can be displayed with the
hand±held tester or generic OBD II scan tool.
These scan tools can display pending DTCs and current DTCs.
Some DTC aren't stored if the ECM doesn't detect a malfunc-
tion during consecutive driving. However, the detected mal-
function during once driving is stored as pending DTC.
(a) Connect the hand±held tester to the Controller Area Net-
work Vehicle Interface Module (CAN VIM). Then connect
the CAN VIM to the Data Link Connector 3 (DLC3).
(b) Turn the ignition switch ON.
(c) Enter the following menus: DIAGNOSIS / ENHANCED
OBD II / DTC INFO / CURRENT CODES (or PENDING
CODE).
(d) Confirm the DTCs and freeze frame data and then write
them down.
(e) See page DI±573 to confirm the details of the DTCs.
NOTICE:
When simulating a symptom with the scan tool to check for
DTCs, use normal mode. For codes on DIAGNOSTIC
TROUBLE CODE CHART subject to º2±trip detection log-
icº, perform the following actions.
Turn the ignition switch OFF after the symptom is simulated
once. Then repeat the simulation process again. When the
problem has been simulated twice, the MIL illuminates and the
DTCs are recorded in the ECM.
2. CLEAR DTC
(a) Connect the hand±held tester to the CAN VIM. Then con-
nect the CAN VIM to the DLC3.
(b) Turn the ignition switch ON.
(c) Enter the following menus: DIAGNOSIS / ENHANCED
OBD II / DTC INFO / CLEAR CODES and press YES.

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±575
769 Author: Date:
2005 SEQUOIA (RM1146U)P2772*
(DI±685)
Transfer L4 SW Circuit
Short in transfer L4 position switch circuit
Transfer L4 position switch
4WD control ECU
ECM


HINT:
*: 4WD

DIDJ5±01
DI±576
± DIAGNOSTICSAUTOMATIC TRANSMISSION
770 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT INSPECTION
DTC P0705 Transmission Range Sensor Circuit Mal-
function (PRNDL Input)
CIRCUIT DESCRIPTION
The park/neutral position switch detects the shift lever position and sends signals to the ECM.
DTC No.DTC Detection ConditionTrouble Area
P0705
(2±trip detection logic)

All switches are OFF simultaneously for NSW, R, N, D, 3 and
2 positions.

2 or more switches are ON simultaneously for NSW, R, D, 3
and 2 positions.

Open or short in park/neutral position switch circuit

Park/neutral position switch

ECM
MONITOR DESCRIPTION
These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral
position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that engine can be started
only when the shift lever is in the P or N position.
The park/neutral position switch sends a signal to the ECM according to the shift position (NSW, R, D, 3 or
2).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position
signal simultaneously. The ECM will turn on the MIL and store the DTC.
MONITOR STRATEGY
Related DTCsP0705Park/neutral position switch/Verify switch input
Required sensors/ComponentsPark/neutral position switch
Frequency of operationContinuous
DtiCondition (A)2 sec.DurationCondition (B)60 sec.
MIL operation2 driving cycle
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
The monitor will run whenever this DTC is
not present.See page DI±545
Ignition switchON
Battery voltage10.5 V or more

D14218
ECM
R
D
2 3 E78
STAR/NSW
11
E5
E521
E519
E510 J52
J52
J52
J52
J52
J52 J/C
J51
J51
J51
J51
J51
J51B
L±Y
B±Y
W±R
L
LG LGL W±RB±YL±Y
L±R
L±R
B±Y W±L
W BG±R* G±R P
PL
RL
NL
DL
2L
LL IG49
1D 1C
IPOGAUGE
IG1
AM1 74
8
7
1C
1L16AM1
2 1 ALT
BatteryF10
FL BlockCowl Side J/B LHI18
Ignition SW Cowl Side J/B RHTo 4WD Control ECU
To Translate ECU To Starter RelayP1
Park/Neutral Position SW
*: 4WD 21 N
8 54
5
6
1
9
7
3
8AEG GF HA H
C C
F
E
2
RB DI±578
± DIAGNOSTICSAUTOMATIC TRANSMISSION
772 Author: Date:
2005 SEQUOIA (RM1146U)
WIRING DIAGRAM

± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±685
879 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P2772 Transfer L4 SW Circuit
CIRCUIT DESCRIPTION
The ECM detects the signal from the transfer L4 position switch.
This DTC indicates that the transfer L4 position switch remains ON.
DTC No.DTC Detecting ConditionTrouble Area
P2772
Transfer L4 position switch remains ON while vehicle running
under conditions for 18 seconds or more (1±trip detection log-
ic)
(a) Output shaft speed 3000 rpm or less
(b) Transfer shift position is H
Short in transfer L4 position switch circuit

Transfer L4 position switch

4WD control ECU

ECM
MONITOR DESCRIPTION
The ECM monitors the transfer±case L4 position switch to determine when the transfer±case L4 gear is en-
gaged. If the transfer±case L4 gears remain engaged under the following conditions, the ECM will conclude
that there is a malfunction of the L4 position switch:

L4 switch indicated that the L4 transfer±case gears are engaged.

Transfer±case shifter is in the ºHº position.

Transfer±case output shaft rpm is between 750 and 3,000 rpm.

The specified time period has elapsed.
If all of the above conditions are detected, the ECM will conclude that there is a malfunction of the L4 switch,
and illuminate the MIL and store the DTC.
MONITOR STRATEGY
Related DTCsP2772Transfer L4 position switch/ON malfunction
Required sensors/ComponentsTransfer L4 position switch
Frequency of operationContinuous
DtiON malfunction (A)1.8 sec.DurationON malfunction (B)0.5 sec.
MIL operation1 driving cycle
Sequence of operationNone
TYPICAL ENABLING CONDITIONS
ItSpecificationItemMinimumMaximum
All:
Output speed sensor circuitNot circuit malfunction
Vehicle speed sensor circuitNot circuit malfunction
Transfer neutral position switchOFF
ON malfunction (A)
Output speed (Transfer output speed)1,000 to 3,000 rpm
ON malfunction (B)
Output speed (Transfer output speed)143 rpm or more±
DIDJQ±01