2001 TOYOTA AVALON oil

SS0ET-02
SS-22
- SERVICE SPECIFICATIONSCHARGING
138 Author
: Date
:
2001 AVALON (RM808U)
CHARGING
SERVICE DATA
BatterySpecific gravity
(Except maintenance-free battery) at 20°C (68°F)
Voltage
(Maintenance-free battery) at 20°C (68°F)
1.25 - 1.29
12.5 - 12.9 V
Drive beltTension
New belt
Used belt
175 ± 5 lbf
115 ± 20 lbf
GeneratorRated output
Rotor coil resistance at 20°C (68°F)
Slip ring diameter STD
Minimum
Brush exposed length STD
Minimum12 V 100 A
2.1 - 2.5 W
14.2 - 14.4 mm (0.559 - 0.567 in.)
12.8 mm (0.504 in.)
10.5 mm (0.413 in.)
1.5 mm (0.059 in.)
Voltage regulatorRegulating voltage13.2 - 14.8 V

SS0EU-02
- SERVICE SPECIFICATIONSCHARGING
SS-23
139 Author
: Date
:
2001 AVALON (RM808U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Bearing retainer x Drive end frame3.03127 in.´lbf
Rectifier end frame x Drive end frame4.54640 in.´lbf
Cord clamp x Rectifier end frame5.45548 in.´lbf
Generator pulley x Rotor110.51,12581
Rectifier holder x Coil lead on rectifier end frame2.93026 in.´lbf
Voltage regulator and brush holder x Rectifier end frame2.02018 in.´lbf
Plate terminal x Rectifier holder3.93935 in.´lbf
Rear end cover x Rectifier holder4.44539 in.´lbf
Terminal insulator x Rectifier holder4.14236 in.´lbf
Generator x Generator bracket5657041
Generator x Adjusting bar1818013
Generator wire x Generator9.810086 in.´lbf

SS0EF-02
SS-6
- SERVICE SPECIFICATIONSENGINE MECHANICAL
122 Author
: Date
:
2001 AVALON (RM808U)
ENGINE MECHANICAL
SERVICE DATA
Compression
pressureat 250 rpm STD
Minimum
Difference of pressure between each cylinder1,500 kPa (15.3 kgf/cm2, 218 psi)
1,000 kPa (10.2 kgf/cm2, 145 psi)
100 kPa (1.0 kgf/cm2, 15 psi) or less
Valve
clearanceat cold Intake
Exhaust
Adjusting shim for repair part Mark 2.500
Mark 2.550
Mark 2.600
Mark 2.650
Mark 2.700
Mark 2.750
Mark 2.800
Mark 2.850
Mark 2.900
Mark 2.950
Mark 3.000
Mark 3.050
Mark 3.100
Mark 3.150
Mark 3.200
Mark 3.250
Mark 3.3000.15 - 0.25 mm (0.006 - 0.010 in.)
0.25 - 0.35 mm (0.010 - 0.014 in.)
2.500 mm (0.0984 in.)
2.550 mm (0.1004 in.)
2.600 mm (0.1024 in.)
2.650 mm (0.1043 in.)
2.700 mm (0.1063 in.)
2.750 mm (0.1083 in.)
2.800 mm (0.1102 in.)
2.850 mm (0.1122 in.)
2.900 mm (0.1142 in.)
2.950 mm (0.1161 in.)
3.000 mm (0.1181 in.)
3.050 mm (0.1201 in.)
3.100 mm (0.1220 in.)
3.150 mm (0.1240 in.)
3.200 mm (0.1260 in.)
3.250 mm (0.1280 in.)
3.300 mm (0.1299 in.)
Ignition timingw/ Terminals TE1 and E1 connected of DLC18 - 12° BTDC @ idle
Idle speed-650 ± 50 rpm
Timing belt
tensionerProtrusion from housing side10.0 - 10.8 mm (0.394 - 0.425 in.)
Cylinder headWarpage Maximum
Valve seat
Refacing angle
Contacting angle
Contacting width
Valve guide bushing bore diameter STD
O/S 0.05
12 pointed head cylinder head bolt diameter
at tension portion STD
Minimum0.10 mm (0.039 in.)
30°, 45°, 75°
45°
1.0 - 1.4 mm (0.039 - 0.055 in.)
10.295 - 10.313 mm (0.4053 - 0.4080 in.)
10.345 - 10.363 mm (0.4073 - 0.4080 in.)
8.95 - 9.05 mm (0.3524 - 0.3563 in.)
8.75 mm (0.3445 in.)
Valve guide
bushingInside diameter
Outside diameter for repair part STD
O/S 0.055.510 - 5.530 mm (0.2169 - 0.2177 in.)
10.333 - 10.344 mm (0.4068 - 0.4072 in.)
10.383 - 10.394 mm (0.4088 - 0.4092 in.)
ValveValve overall length STD Intake
Exhaust
Minimum Intake
Exhaust
Valve face angle
Stem diameterIntake
Exhaust
Stem oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Margin thickness STD
Maximum95.45 mm (3.5779 in.)
95.40 mm (3.7559 in.)
94.95 mm (3.7382 in.)
94.90 mm (3.7362 in.)
44.5°
5.470 - 5.485 mm (0.2154 - 0.2159 in.)
5.465 - 5.480 mm (0.2152 - 0.2157 in.)
0.025 - 0.060 mm (0.0010 - 0.0024 in.)
0.030 - 0.065 mm (0.0012 - 0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
1.0 mm (0.039 in.)
0.5 mm (0.020 in.)

- SERVICE SPECIFICATIONSENGINE MECHANICAL
SS-7
123 Author
: Date
:
2001 AVALON (RM808U) Valve spring
Deviation Maximum
Free length
Installed tension at 33.8 mm (1.331 in.)2.0 mm (0.079 in.)
45.50 mm (1.7913 in.)
186 - 206 N (19.0 - 21.0 kgf, 41.9 - 46.3 lbf)
Valve lifterLifter diameter
Lifter bore diameter
Oil clearance STD
Maximum30.966 - 30.976 mm (1.2191 - 2.2195 in.)
31.000 - 31.016 mm (1.2205 - 1.2211 in.)
0.024 - 0.050 mm (0.0009 - 0.0020 in.)
0.07 mm (0.0028 in.)
CamshaftThrust clearance STD
Maximum
Journal oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Journal diameter
Circle runout Maximum
Cam lobe height STD Intake
Exhaust
Minimum Intake
Exhaust
Camshaft gear backlash STD
Maximum
Camshaft gear spring end free distance0.040 - 0.090 mm (0.0016 - 0.0035 in.)
0.12 mm (0.0047 in.)
0.035 - 0.072 mm (0.0014 - 0.0028 in.)
0.025 - 0.062 mm (0.0010 - 0.0024 in.)
0.10 mm (0.0039 in.)
0.09 mm (0.0035 in.)
26.949 - 26.965 mm (1.0610 - 1.0616 in.)
0.06 mm (0.0024 in.)
42.11 - 42.21 mm (1.6579 - 1.6618 in.)
41.96 - 42.06 mm (1.6520 - 1.6559 in.)
41.96 mm (1.6520 in.)
41.81 mm (1.6461 in.)
0.020 - 0.200 mm (0.0008 - 0.0079 in.)
0.30 mm (0.0188 in.)
18.2 - 18.8 mm (0.712 - 0.740 in.)
Air intake
chamberWarpage Maximum0.10 mm (0.0039 in.)
Intake
manifoldWarpage
Air intake chamber side Maximum
Cylinder head side Maximum
0.15 mm (0.0059 in.)
0.08 mm (0.0031 in.)
Exhaust
manifoldWarpage Maximum0.50 mm (0.0196 in.)
Cylinder blockCylinder head surface warpage Maximum
Cylinder bore diameter
Maximum
12 pointed head main bearing cap bolt diameter
at tension portion STD
Minimum0.07 mm (0.0028 in.)
87.500 - 87.512 mm (3.4449 - 3.4453 in.)
87.52 mm (3.4457 in.)
7.500 - 7.600 mm (0.2953 - 0.2992 in.)
7.20 mm (0.2835 in.)
Piston and
piston ringPiston diameter
AISIN made
at 23.2 mm (0.913 in.) from the piston head
MAHLE made
at 41.2 mm (1.622 in.) from the piston head
Piston oil clearance
AISIN made STD
Maximum
MAHLE made STD
Maximum
Piston ring groove clearance No.1
No.2
Piston ring end gap STD No.1
No.2
Oil
Maximum No.1
No.2
Oil
87.406 - 87.416 mm (3.4412 - 3.4416 in.)
87.453 - 87.467 mm (3.4430 - 3.4436 in.)
0.084 - 0.106 mm (0.0033 - 0.0042)
0.13 mm (0.0051 in.)
0.033 - 0.059 mm (0.0013 - 0.0023)
0.08 mm (0.0031 in.)
0.020 - 0.070 mm (0.0008 - 0.0028 in.)
0.020 - 0.060 mm (0.0008 - 0.0024 in.)
0.25 - 0.35 mm (0.0098 - 0.0138 in.)
0.35 - 0.45 mm (0.0138 - 0.0177 in.)
0.15 - 0.40 mm (0.0059 - 0.0157 in.)
0.95 mm (0.0374 in.)
1.05 mm (0.0413 in.)
1.00 mm (0.0394 in.)

SS-8
- SERVICE SPECIFICATIONSENGINE MECHANICAL
124 Author
: Date
:
2001 AVALON (RM808U) Connecting
rod
Thrust clearance STD
Maximum
Connecting rod thickness
Connecting rod bearing center wall thickness
Reference Mark 1
Mark 2
Mark 3
Mark 4
Connecting rod oil clearance STD
Maximum
Rod bend Maximum per 100 mm (3.94 in.)
Rod twist Maximum per 100 mm (3.94 in.)
Bushing inside diameter
Piston pin diameter
Bushing oil clearance STD
Maximum
Connecting rod bolt diameter
at tension portion STD
Minimum0.15 - 0.30 mm (0.0059 - 0.0118 in.)
0.35 mm (0.0138 in.)
20.80 - 20.85 mm (0.8189 - 0.8209 in.)
1.484 - 1.487 mm (0.0584 - 0.0585 in.)
1.487 - 1.490 mm (0.0585 - 0.0587 in.)
1.490 - 1.493 mm (0.0587 - 0.0588 in.)
1.493 - 1.496 mm (0.0588 - 0.0589 in.)
0.038 - 0.064 mm (0.0015 - 0.0025 in.)
0.08 mm (0.0031 in.)
0.05 mm (0.0020 in.)
0.15 mm (0.0059 in.)
22.005 - 22.014 mm (0.8663 - 0.8667 in.)
21.997 - 22.006 mm (0.8660 - 0.8664 in.)
0.005 - 0.011 mm (0.0002 - 0.0004 in)
0.05 mm (0.0020 in.)
7.2 - 7.3 mm (0.284 - 0.287 in.)
7.0 mm (0.276 in.)
CrankshaftThrust clearance STD
Maximum
Thrust washer thickness
Main journal oil clearance STD No.1 and No.4
No.2 and No.3
Maximum No.1 and No.4
No.2 and No.3
Main journal diameter
Main bearing center wall thickness
Reference Mark 10.04 - 0.24 mm (0.0016 - 0.0095 in.)
0.30 mm (0.0118 in.)
1.930 - 1.980 mm (0.0760 - 0.0780 in.)
0.016 - 0.036 mm (0.0006 - 0.0014 in.)
0.028 - 0.048 mm (0.0011 - 0.0019 in.)
0.05 mm (0.0020 in.)
0.06 mm (0.0024 in.)
60.988 - 61.000 mm (2.4011 - 2.4016 in.)
2.485 - 2.488 mm (0.0978 - 0.0980 in.)
Reference Mark 1
Mark 2
Mark 3
Mark 4
Mark 5
Mark 6
Mark 7
Crank pin diameter
Circle runout Maximum
Main journal taper and out-of-round Maximum
Crank pin taper and out-of-round Maximum
2.485 2.488 mm (0.0978 0.0980 in.)
2.488 - 2.491 mm (0.0980 - 0.0981 in.)
2.491 - 2.494 mm (0.0981 - 0.0982 in.)
2.494 - 2.497 mm (0.0982 - 0.0983 in.)
2.497 - 2.500 mm (0.0983 - 0.0984 in.)
2.500 - 2.503 mm (0.0984 - 0.0985 in.)
2.503 - 2.506 mm (0.0985 - 0.0987 in.)
52.992 - 53.000 mm (2.0863 - 2.0866 in.)
0.06 mm (0.0024 in.)
0.02 mm (0.0008 in.)
0.02 mm (0.0008 in.)

SS0EG-02
- SERVICE SPECIFICATIONSENGINE MECHANICAL
SS-9
125 Author
: Date
:
2001 AVALON (RM808U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Timing belt plate x Oil pump88069 in.´lbf
No.1 idler pulley x Oil pump3435025
No.2 idler pulley x No.2 idler pulley bracket4344032
Camshaft timing pulley x Camshaft
for SST125
881,300
90094
65
Timing belt tensioner x Oil pump2728020
RH engine mounting bracket x Cylinder block2829021
No.2 timing belt cover x No.3 timing belt cover8.58574 in.´lbf
No.1 timing belt cover x Oil pump8.58574 in.´lbf
Crankshaft pulley x Crankshaft2152,200159
No.2 generator bracket x Engine RH mounting bracket2829021
Cylinder head x Cylinder block 12 pointed head 1st
2nd
Recessed head54
Turn 90°
18.5550
Turn 90°
18540
Turn 90°
13
Camshaft bearing cap x Cylinder head1616012
Cylinder head cover x Cylinder head88069 in.´lbf
Exhaust manifold x Cylinder head4950036
Exhaust manifold stay x Exhaust manifold California
Except California34
20350
20025
15
Exhaust manifold stay x Transmission housing California
Except California34
20350
20025
15
No.1 EGR pipe x RH exhaust manifold121209
No.1 EGR pipe x EGR cooler121209
PS pump bracket x RH cylinder head4344032
Oil dipstick guide x LH cylinder head88069 in.´lbf
Water inlet pipe x LH cylinder head19.520014
Cylinder head rear plate x LH cylinder head88069 in.´lbf
No.3 timing belt cover x Cylinder head8.58574 in.´lbf
Water outlet x Intake manifold1515011
Fuel inlet hose x Fuel filter2930021
Intake manifold x Cylinder head1515011
Air intake chamber x Intake manifold4344032
No.2 EGR pipe x Air intake chamber121209
No.2 EGR pipe x EGR cooler121209
No.1 engine hanger x Air intake chamber3940029
No.1 engine hanger x RH cylinder head3940029
Air intake chamber stay x Air intake chamber19.520014
Air intake chamber stay x RH cylinder head19.520014
Main bearing cap x Cylinder block 12 pointed head 1st
2nd
6 pointed head22
Turn 90°
27225
Turn 90°
27516
Turn 90°
20
Connecting rod cap x Connecting rod 1st
2nd24.5
Turn 90°250
Turn 90°18
Turn 90°
Rear oil seal retainer x Cylinder block88069 in.´lbf
EGR cooler x Cylinder block99078 in.´lbf

SS-10
- SERVICE SPECIFICATIONSENGINE MECHANICAL
126 Author
: Date
:
2001 AVALON (RM808U) Engine coolant drain union x Cylinder block
3940029
Water seal plate x Cylinder block1818013
Oil filter union x Cylinder block3031022
Water inlet housing x Cylinder block88069 in.´lbf
Knock sensor x Cylinder block3940029
No.2 idler pulley bracket x Cylinder block2829021
A/C compressor housing bracket x Cylinder block2525018
Generator bracket x Cylinder block4344032
Drive plate x Crankshaft8385061
Transaxle x Engine6465047
No.1 oil pan x Transaxle37.238027
Drive plate x Torque convertor clutch4142030
Flywheel housing under cover x Transaxle7.88069 in.´lbf
Rear engine mounting insulator x Cylinder block6465047
Front engine mounting insulator x Cylinder block6465047
Engine moving control rod x RH engine mounting bracket6465047
Engine moving control rod x RH fender apron6465047
RH engine mounting stay x Water outlet3232023
RH engine mounting stay x Engine moving control rod3232023
RH engine mounting stay x No.2 RH engine mounting bracket3232023
Front engine mounting insulator x Front frame Silver color bolt
Green color bolt44
66450
67032
49
Engine mounting absorber x Front frame4849035
Engine mounting absorber x Transaxle4849035
Rear engine mounting insulator x Front frame6667048
LH engine mounting insulator x Transaxle6465047
PS pump x PS pump bracket4344031
A/C compressor x Housing bracket25.526019
A/C compressor x No.1 oil pan25.526019
Generator adjusting bar x Drive belt adjusting bar bracket1818513
Fuel inlet hose x Fuel filter2930021
Front exhaust pipe support bracket x No.1 oil pan20.621015
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Center exhaust pipe5657041
Center exhaust pipe x Tailpipe5657041
Front exhaust pipe bracket x Sub frame3333024
Front exhaust pipe support bracket x Front exhaust pipe stay3333024

SS0EQ-01
- SERVICE SPECIFICATIONSIGNITION
SS-19
135 Author
: Date
:
2001 AVALON (RM808U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Spark plug x Cylinder head1818013
Ignition coil x Cylinder head88069 in.´lbf
Camshaft position sensor x Cylinder head88069 in.´lbf
Crankshaft position sensor x Oil pump88069 in.´lbf