2001 CHRYSLER VOYAGER light

TEST ACTION APPLICABILITY
7 Turn the ignition off.
Disconnect the BCM C4 harness connector.
Disconnect the Instrument Cluster harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Instrument Cluster Wake
Up Sense circuit.
Is the test light illuminated?All
Ye s®Repair the Instrument Cluster Wake Up Sense circuit for a short
to voltage.
Perform BODY VERIFICATION TEST - VER 1.
No®Replace the Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.
8 Turn the ignition off.
Reconnect the BCM C4 harness connector.
Disconnect the Instrument Cluster harness connector.
Measure the resistance between ground and the Instrument Cluster Wake Up Sense
circuit at the Instrument Cluster connector.
Open and close a door. This is done to ensure the BCM is awake.
Is the resistance below 50.0 ohms?All
Ye s®Replace the Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.
No®Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
9 Turn the ignition off.
Disconnect the Instrument Cluster harness connector.
Disconnect the BCM C4 harness connector.
Measure the resistance of the Instrument Cluster Wake Up Sense circuit between the
BCM C4 connector and the MIC connector.
Is the resistance below 5.0 ohms?All
Ye s®Replace the Instrument Cluster.
Perform BODY VERIFICATION TEST - VER 1.
No®Repair the Instrument Cluster Wake Up Sense circuit for an
open.
Perform BODY VERIFICATION TEST - VER 1.
385
COMMUNICATION
*BUS +/- SIGNALS OPEN OR NO RESPONSE FROM INSTRUMENT CLUS-
TER Ð
Continued

Symptom:
*BUS +/- SIGNALS OPEN OR NO RESPONSE FROM LEFT SLIDING
DOOR CONTROL MODULE
POSSIBLE CAUSES
FUSED B(+) CIRCUIT OPEN
LEFT SLIDING DOOR WAKE UP SIGNAL WIRE OPEN
LEFT SLIDING DOOR WAKE UP SIGNAL WIRE SHORT TO VOLTAGE
GROUND CIRCUIT OPEN
LEFT SLIDING DOOR WAKE UP SIGNAL WIRE SHORT TO GROUND
PCI BUS CIRCUIT OPEN
BODY CONTROL MODULE - LEFT SLIDING DOOR WAKE UP GROUND OPEN
LEFT SLIDING DOOR CONTROL MODULE - OPEN
TEST ACTION APPLICABILITY
1Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the Left Sliding Door Control Module C1 connector.
Measure the voltage between Fused B(+) circuit and ground.
Is the voltage above 10.0 volts?All
Ye s®Go To 2
No®Repair the Fused B(+) circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
2Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the Left Sliding Door Control Module C1 connector.
Using a 12-volt test light connected to 12-volts, check the Ground circuit.
Does the test light illuminate brightly?All
Ye s®Go To 3
No®Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
386
COMMUNICATION

Symptom:
*BUS +/- SIGNALS OPEN OR NO RESPONSE FROM POWER LIFT-
GATE MODULE
POSSIBLE CAUSES
BODY CONTROL MODULE - LIFTGATE WAKE UP GROUND OPEN
FUSED B(+) CIRCUIT OPEN
LIFTGATE MODULE WAKE UP SIGNAL WIRE OPEN
LIFTGATE MODULE WAKE UP SIGNAL WIRE SHORT TO VOLTAGE
GROUND CIRCUIT OPEN
LIFTGATE MODULE WAKE UP SIGNAL WIRE SHORT TO GROUND
PCI BUS CIRCUIT OPEN
POWER LIFTGATE MODULE - OPEN
TEST ACTION APPLICABILITY
1Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the Power Liftgate Module C1 connector.
Measure the voltage between Fused B(+) circuit and ground.
Is the voltage above 10.0 volts?All
Ye s®Go To 2
No®Repair the Fused B(+) circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
2Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the Power Liftgate Module C2 connector.
Using a 12-volt test light connected to 12-volts, check the Ground circuit.
Does the test light illuminate brightly?All
Ye s®Go To 3
No®Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
389
COMMUNICATION

Symptom:
*BUS +/- SIGNALS OPEN OR NO RESPONSE FROM RIGHT SLID-
ING DOOR CONTROL MODULE
POSSIBLE CAUSES
FUSED B(+) CIRCUIT OPEN
RIGHT SLIDING DOOR WAKE UP SIGNAL WIRE OPEN
RIGHT SLIDING DOOR WAKE UP SIGNAL WIRE SHORT TO VOLTAGE
GROUND CIRCUIT OPEN
RIGHT SLIDING DOOR WAKE UP SIGNAL WIRE SHORT TO GROUND
PCI BUS CIRCUIT OPEN
BODY CONTROL MODULE - RIGHT SLIDING DOOR WAKE UP GROUND OPEN
RIGHT POWER SLIDING DOOR MODULE - OPEN
TEST ACTION APPLICABILITY
1Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the Right Sliding Door Control Module C1 connector.
Measure the voltage between Fused B(+) circuit and ground.
Is the voltage above 10.0 volts?All
Ye s®Go To 2
No®Repair the Fused B(+) circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
2Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the Right Sliding Door Control Module C1 connector.
Using a 12-volt test light connected to 12-volts, check the Ground circuit.
Does the test light illuminate brightly?All
Ye s®Go To 3
No®Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
392
COMMUNICATION

Symptom:
*BUS +/- SIGNALS OPEN OR NO RESPONSE FROM THATCHAM
ALARM MODULE
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE BCM
GROUND CIRCUIT OPEN
FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN
OPEN PCI BUS CIRCUIT
THATCHAM ALARM MODULE
TEST ACTION APPLICABILITY
1 Turn the ignition on.
With the DRB, enter Body then Body Computer.
Was the DRB able to I/D or communicate with the BCM?All
Ye s®Go To 2
No®Refer to the symptom list for problems related to no communica-
tion with the BCM.
Perform BODY VERIFICATION TEST - VER 1.
2 Turn the ignition off.
Disconnect the RKE Module 6-way harness connector.
Measure the resistance between ground and the ground circuit.
Is the resistance below 5.0 ohms?All
Ye s®Go To 3
No®Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
3 Turn the ignition off.
Disconnect the Thatcham Alarm Module C1 harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Fused Ignition Switch
Output circuit.
Is the test light illuminated?All
Ye s®Go To 4
No®Repair the Fused Ignition Switch Output circuit for an open or
short.
Perform BODY VERIFICATION TEST - VER 1.
395
COMMUNICATION

Symptom:
*NO RESPONSE FROM CABIN HEATER ASSIST - DIESEL ONLY
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE ECM
FUSED B+ CIRCUIT OPEN
GROUND CIRCUIT OPEN
SCI TRANSMIT CIRCUIT OPEN
CABIN HEATER ASSIST
TEST ACTION APPLICABILITY
1 Turn the ignition on.
With the DRB, attempt to communicate with the ECM.
Was the DRB able to I/D or communicate with the ECM?All
Ye s®Go To 2
No®Refer to the symptom list for problems related to no communica-
tion with the ECM.
Perform CABIN HEATER VERIFICATION TEST - VER 1.
2 Turn the ignition off.
Disconnect the Cabin Heater Assist C2 harness connector.
Using a 12-volt test light connected to ground, probe the Fused B+ circuit.
Is the test light illuminated?All
Ye s®Go To 3
No®Check the IPM Fuse #15 for an open. If open, check for a short to
ground on the Fused B+ circuit. If not open, repair the Fused B+
circuit for an open.
Perform CABIN HEATER VERIFICATION TEST - VER 1.
3 Turn the ignition off.
Disconnect the Cabin Heater Assist C2 harness connector.
Measure the resistance between ground and the ground circuit.
Is the resistance below 5.0 ohms?All
Ye s®Go To 4
No®Repair the ground circuit for an open.
Perform CABIN HEATER VERIFICATION TEST - VER 1.
4 Turn the ignition off.
Disconnect the Cabin Heater Assist C1 harness connector.
Disconnect the DRB from the DLC.
Measure the resistance of the SCI Transmit circuit between the Cabin Heater Assist
connector and the DLC.
Is the resistance below 5.0 ohms?All
Ye s®Go To 5
No®Repair the SCI Transmit circuit for an open.
Perform CABIN HEATER VERIFICATION TEST - VER 1.
397
COMMUNICATION

Symptom:
*NO RESPONSE FROM CONTROLLER ANTILOCK BRAKE
POSSIBLE CAUSES
NO RESPONSE FROM CAB
GROUND CIRCUIT OPEN
OPEN FUSED IGNITION SWITCH OUTPUT CIRCUIT
OPEN PCI BUS CIRCUIT
CONTROLLER ANTILOCK BRAKE
TEST ACTION APPLICABILITY
1 Turn the ignition on.
Note: As soon as one or more module communicates with the DRB, answer
the question.
With the DRB, attempt to communicate with the Airbag Control Module (ACM).
With the DRB, attempt to communicate with the Body Control Module (BCM).
Was the DRB able to I/D or establish communications with either of the modules?All
Ye s®Go To 2
No®Refer to the Communications category and perform the symptom
PCI Bus Communication Failure.
Perform ABS VERIFICATION TEST - VER 1.
2 Turn the ignition off.
Disconnect the CAB harness connector.
Measure the resistance between ground and both ground circuits.
Is the resistance below 5.0 ohms for both measurements?All
Ye s®Go To 3
No®Repair the ground circuit(s) for an open.
Perform ABS VERIFICATION TEST - VER 1.
3 Turn the ignition off.
Disconnect the CAB harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Fused Ignition Switch
Output circuit.
Is the test light illuminated?All
Ye s®Go To 4
No®Repair the Fused Ignition Switch Output circuit for an open.
Perform ABS VERIFICATION TEST - VER 1.
399
COMMUNICATION

Symptom:
*NO RESPONSE FROM ORC
POSSIBLE CAUSES
CHECKING FOR VOLTAGE AT ORC
ORC GROUND CIRCUIT OPEN
PCI BUS CIRCUIT OPEN
OCCUPANT RESTRAINT CONTROLLER
TEST ACTION APPLICABILITY
1NOTE: Check the FCM for DTC's. If DTC's are present, go to the appropriate
category and perform the DTC.
Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
Disconnect the Occupant Restraint Controller harness connector.
Turn the ignition on and then reconnect the Battery.
Using a 12-volt test light connected to ground, probe the ORC Run Only Driver
Circuit and the ORC Run/Start Driver Circuit at the ORC connector.
NOTE: One open circuit will not cause a NO RESPONSE condition.
Is the test light illuminated on both circuits?All
Ye s®Go To 2
No®Repair the ORC Run Only Driver and ORC Run/Start Driver
circuits for an open.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting airbag system components, the ignition must be
turned off and the battery must be disconnected.
2Ensure that the battery is fully charged.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
Disconnect the Occupant Restraint Controller harness connector.
Measure the resistance between ground and the ground circuit.
Is the resistance below 5.0 ohms?All
Ye s®Go To 3
No®Repair the Ground circuit for an open.
Perform AIRBAG VERIFICATION TEST - VER 1.
When reconnecting Airbag system components, the ignition must be turned
off and the battery must be disconnected.
408
COMMUNICATION