2000 TOYOTA CAMRY codes

READINESS MONITOR DRIVE PATTERNS ± EG003-02 RevisedMarch 29, 2002
Page 18 of 23
DRIVE PATTERN NO. 7: EVAP Monitor (Without Leak Detection)
43 ± 56 mph
(70 ± 90 km/h)
Idling
IG SW off
3 ± 5 min 3 ± 5 min3 ± 5 min
(a) (b)3 ± 5 min
(c) Warm up
ECT.181F
Preconditions
The monitor will not run unless:

MIL is OFF.

Altitude is 7800 feet (2400 m) or less.

ECT (Coolant Temp) is 181F (83C) or greater.

IAT (Intake Air) is 41F (5C) or greater.
Drive Pattern Procedure
Connect the OBDII Scantool to DLC3 to check monitor status and preconditions.
a. Drive the vehicle at 43 ± 56 mph (70 ± 90 km/h) for a period of 3 ± 5 minutes.
NOTE:

Do not allow the Throttle Position (TP) to exceed 30%.

Drive with smooth throttle operation and avoid sudden acceleration.
b. Stop the vehicle and let the engine idle for 3 ± 5 minutes.
c. Repeat steps ªaº and ªbº once.
If readiness status does not switch to ªcomplete,º ensure preconditions are met, turn the
ignition OFF, then repeat steps ªaº through ªc.º
NOTE:
The readiness status may not switch to ªcompleteº after the first drive pattern trip if a
Pending Code has been set (first trip for a two±trip DTC).

Pending Codes are available from the DTC Info Menu in Enhanced OBDII.

Pending Codes indicate a POTENTIAL problem was detected. A second trip is
needed to confirm the DTC prior to diagnosis.

Once a second trip is completed, a current DTC will be stored. Readiness
Monitor
Drive
Patterns:
EVAP
Monitors
(Continued)

READINESS MONITOR DRIVE PATTERNS ± EG003-02 RevisedMarch 29, 2002
Page 21 of 23
DRIVE PATTERN NO. 9: Oxygen Sensor Monitor (Front and Rear O2S System)
Once
Twice 3 times 10 times
25 mph
(40 km/h)
(over 900
rpm)
Idling
IG SW off
Over
2 min
(a)Over
50 sec Over
50 sec
(b)50 sec 50 sec Over
40
sec
(c)Over
40
sec40
sec
(d)
Preconditions
The monitor will not run unless:

MIL is OFF.
Drive Pattern Procedure
Connect the OBDII Scantool to DLC3 to check monitor status and preconditions.
a. Start the engine and allow it to idle for 2 minutes or more.
b. Drive the vehicle at 25 mph (40 km/h) or more for at least 50 seconds.
Be sure engine speed remains above 900 rpm.
c. Stop the vehicle and allow the engine to idle for 40 seconds or more.
d. Perform steps ªbº and ªcº ten times.
If readiness status does not switch to ªcomplete,º ensure preconditions are met, turn the
ignition OFF, then repeat steps ªaº through ªd.º
NOTE:
The readiness status may not switch to ªcompleteº after the first drive pattern trip if a
Pending Code has been set (first trip for a two±trip DTC).

Pending Codes are available from the DTC Info Menu in Enhanced OBDII.

Pending Codes indicate a POTENTIAL problem was detected. A second trip is
needed to confirm the DTC prior to diagnosis.

Once a second trip is completed, a current DTC will be stored. Readiness
Monitor
Drive
Patterns:
Oxygen
Monitors

READINESS MONITOR DRIVE PATTERNS ± EG003-02 RevisedMarch 29, 2002
Page 22 of 23
DRIVE PATTERN NO. 10: Oxygen/Air Fuel Ratio Sensor Monitor
(Front AF Sensor and Rear O2S System)
40 ± 70 mph
(64 ± 112 km/h)
(900 ± 3,200 rpm)
Idling
IG SW offOnce Twice 10 times
Over
2 min
(a)Over
40 sec
(d) 25 mph
(40 km/h)
(over 900 rpm)
Over
3 min
(b)
Over
10 sec
(c)Over
10 sec
(e)Over
40 sec
Over
10 sec40 sec
(f)
Preconditions
The monitor will not run unless:

MIL is OFF.
Drive Pattern Procedure
Connect the OBDII Scantool to DLC3 to check monitor status and preconditions.
a. Start the engine and allow it to idle for 2 minutes or more.
b. Drive the vehicle at 40 ± 70 mph (64 ± 112 km/h) or more for at least 3 minutes.
Be sure to maintain engine speed between 900 and 3,200 rpm.
c. Stop the vehicle and allow the engine to idle for 10 seconds or more.
d. Drive the vehicle at 25 mph (40 km/h) for at least 40 seconds or more.
Be sure to maintain engine speed above 900 rpm.
e. Stop the vehicle and allow the engine to idle for 10 seconds or more.
f. Perform steps ªdº and ªeº ten times.
If readiness status does not switch to ªcomplete,º ensure preconditions are met, turn the
ignition switch OFF, then repeat steps ªaº through ªf.º
NOTE:
The readiness status may not switch to ªcompleteº after the first drive pattern trip if a
Pending Code has been set (first trip for a two±trip DTC).

Pending Codes are available from the DTC Info Menu in Enhanced OBDII.

Pending Codes indicate a POTENTIAL problem was detected. A second trip is
needed to confirm the DTC prior to diagnosis.

Once a second trip is completed, a current DTC will be stored. Readiness
Monitor
Drive
Patterns:
Oxygen
Monitors
(Continued)

READINESS MONITOR DRIVE PATTERNS ± EG003-02 RevisedMarch 29, 2002
Page 23 of 23
DRIVE PATTERN NO. 11: Oxygen/AF Sensor Heater Monitor
Idling
IG SW off
2 min
(b) 9 min
(a) 25 mph
(40 km/h)
Preconditions
The monitor will not run unless:

MIL is OFF.
Drive Pattern Procedure
Connect the OBDII Scantool to DLC3 to check monitor status and preconditions.
a. Start the engine and allow it to idle for 9 minutes.
b. Drive the vehicle at 25 mph (40 km/h) or more for at least 2 minutes.
If readiness status does not switch to ªcomplete,º ensure preconditions are met, turn the
ignition OFF, then repeat steps ªaº and ªb.º
NOTE:
The readiness status may not switch to ªcompleteº after the first drive pattern trip if a
Pending Code has been set (first trip for a two±trip DTC).

Pending Codes are available from the DTC Info Menu in Enhanced OBDII.

Pending Codes indicate a POTENTIAL problem was detected. A second trip is
needed to confirm the DTC prior to diagnosis.

Once a second trip is completed, a current DTC will be stored. Readiness
Monitor
Drive
Patterns:
Oxygen
Monitors
(Continued)

Toyota Supports ASE CertificationPage 1 of 2
EG013±99
Title:
SINGLE CYLINDER MISFIRES
Models:
'99 Avalon, Camry, Sienna & Solara
Technical Service
BULLETIN
December 17, 1999

Some 1999 Avalon, Camry (1MZ±FE), Sienna & Solara (1MZ±FE) vehicles may exhibit a
rough idle, and or a M.I.L. ªONº condition, in which a single cylinder misfire code, or
codes are present. Changes have been made in the fuel injector production process to
correct this condition.
1999 TMMK produced Avalon, Camry (1MZ±FE), Sienna & TMMC produced Solara
(1MZ±FE) vehicles built between the VIN numbers listed below.
MODELSTARTING VINENDING VIN
Avalon4T1BF1#B * XU2985044T1BF1#B*XU319557
Camry4T1BF2#K * XU0764034T1BF2#K*XU081214
Camry (cont.)4T1BF2#K * XU9300244T1BF2#K*XU931330
Sienna4T3ZF1#C * XU0908874T3ZF1#C*XU122589
Solara (U.S.)2T1CF2#P * XC1110832T1CF2#P*XC757508
Solara (Canada)2T1CF2#P * XC7441132T1CF2#P*XC162681
APPLICABLE PARTSQUANTITYPART NAME
23209±0A0106Fuel Injector
OP CODEVWCDESCRIPTIONTIMEOPNT1T2
895221NR & R Fuel Injector Assembly ± All1.823209±0A0100256
Applicable Warranty*:
This repair is covered under the Toyota Federal Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
Coverage is extended to 36 months or 50,000 miles, whichever occurs first, in the
states of California, Massachusetts, and Vermont due to state emission warranty
legislation.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
NOTE:
Be sure to enter the DTC No. in the Condition/Cause/Remedy section, if a DTC Code
appeared.
ENGINE
Introduction
Applicable
Vehicles
Parts
Information
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 2
EL008±98Title:
PROGRAMMING OEM WIRELESS
DOOR LOCK REMOTE TRANSMITTERS
Models:
'97 ± '99 Camry
Technical Service
BULLETIN
December 4, 1998

This bulletin describes procedures used to program the three button remote transmitter to
vehicles that are equipped with Wireless Door Lock Control. The following information
applies
only to the Factory Wireless Door Lock Control, not dealer or port installed
options that also utilize remotes, such as VIP Keyless Entry/RS3000 or any aftermarket
system.
Verification of
Factory Wireless Door Lock Control can easily be performed by identifying
the TDS status monitor, functioning remote, or model grade.
The Remote Transmitter has LOCK,
UNLOCK, and PANIC features.The TDS Status Monitor is located in
the Tachometer.
Transmitter Identification TDS Status Montior Indentification
NOTE:
When a new remote is programmed, all previous codes are erased. Because of this,
all remotes should be entered during the same programming session, otherwise a
remote may no longer be registered and operate the vehicle.
For Customer Satisfaction, request that any existing remote be furnished when
programming a new or replacement unit.
1997 ± 1999 Camrys:
1997 ± 1998 All XLE (standard equipment) and some LE (optional)
1999 All XLE only
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
ELECTRICAL
Introduction
Applicable
Vehicles
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 5
PA002±99Title:
1999 PAINT AND REFINISH FORMULA
CODES
Models:
All 1999 Models
Technical Service
BULLETIN
March 12, 1999

Attached for your reference is a list of all 1999 OEM paint codes and refinish paint codes
for the following paint manufacturers:
BASF, DuPont, ICI Autocolor, PPG, Sherwin Williams, Sikkens,
Spies±Hecker, and Standox
NOTE:
The body color code is on the vehicle Certification Regulation Label, located on the
left front door ªBº Pillar or door rear lower surface.
Please contact your local paint representative for the actual paint
mixing formulas or if you need help in color matching.
All 1999 Models.
OPCODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty±±±±
COLOR
CODECOLOR NAMEBASFDUPONTICI
AUTOCOLORPPGSHERWIN
WILLIAMSSIKKENSSPIES±
HECKERSTANDOX
040Super WhiteTOY040W8430KK479028835000TOY04017143040
049White PearlTOY049N9033
L9018TA99G
PC61B90673
9067440881
40882TOY04997746049
051Diamond White PearlTOY051L9246
L9247PF76B
TD86G90822
9082642872
42873TOY05198125
16329051
056Natural WhiteTOY056F1858BAB59145252893TOY05615217056
PAINT
Introduction
Affected
Vehicles
Warranty
Information
Paint Codes &
Color Names

1999 PAINT AND REFINISH FORMULA CODES ± PA002±99 March 12, 1999
Page 2 of 5
COLOR
CODECOLOR NAMEBASFDUPONTICI
AUTOCOLORPPGSHERWIN
WILLIAMSSIKKENSSPIES±
HECKERSTANDOX
181Silver MetallicTOY181L9245C523B3487844337TOY18198127181
199Alpine Silver MetallicTOY199L99905TX1B490048976TOY19970706199
1A0Platinum MetallicTOY1A0N99236ED5B489649700TOY1A0708091A0
1A2Topaz MetallicTOY1A2F00166ED9B489849701TOY1A2708551A2
1A3Silver MetallicTOY1A3F06977DJ9B3584153001TOY1A3723191A3
1A5Desert Dune PearlTOY1A5F14588NH3B3609052139TOY1A5727591A5
1B1Champagne PearlTOY1B1F2186FLT9B525253074TOY1B1206991B1
1B2Antique Sage PearlTOY1B2F2201HRE5B532454757TOY1B2736221B2
1B9Quiksilver FXTOY1B9F4996LJC5B544956738TOY1B9743321B9
1C0Millennium SilverTOY1C0F4928LCJ4B3664356793TOY1C0745001C0
1C3River Rock Green MicaTOY1C3F4513LVT2B4870357226TOY1C3744881C3
1C4Silverstream OpTOY1C4F5137NPD6B556057927TOY1C4747711C4
1C7Thunder Gray MetallicTOY1C7F5581PEJ6B560058581TOY1C7748061C7
1C8Lunar Mist MetallicTOY1C8F8569PEJ7B553958582TOY1C8748071C8
202BlackTOY202FO22001229510057871TOY20272941202
204Black MetallicTOY204H8645A237B962435533TOY20496020204
205Satin Black MetallicTOY205L9024B941B975640888TOY20597765205
3E5Super RedTOY3E5W8431KK417271735001TOY3E5382363E5
3H7Cardinal RedTOY3H7L9026WJ917327940890TOY3H7388053H7
3J8Prussian Red PearlTOY3J8W9463PT73B459646590TOY3J8998273J8
3K4Sunfire Red PearlTOY3K4W9546PM54B451146144TOY3K4997223K4
3L2Renaissance RedTOY3L2L99925TX3B490248978TOY3L2304913L2
3L5Radiant RedTOY3L5F2688GNK8528754291TOY3L5334763L5
3M5Sandrift MetallicTOY3M5F3531LCP1B544456742TOY3M5342613M5
3M6Napa Burgundy PearlTOY3M6F3747LJC2B544756739TOY3M6342623M6
3M8Venetian Red PearlTOY3M8F4929LCJ5B556156795TOY3M8343003M8
3M9Baroque Red MetallicTOY3M9F4464KWB9B542156658TOY3M9342573M9
3N1Cinnabar PearlTOY3N1F4483LPC9B543556752TOY3N1342543N1
3N2Mahogany PearlTOY3N2F1744LVT3B2876357227TOY3N2343173N2
3N5Red Flame MetallicTOY3N5F5138NPD7B556357928TOY3N5345873N5
3N6Vintage Red PearlTOY3N6F8568PEB8B552558338TOY3N6346223N6
4J6Sadona Sunset MetallicTOY4J6L9028B945B2660140892TOY4J6977534J6
4M4Sierra Beige MetallicTOY4M4H98794SS7B474347606TOY4M4201574M4
Paint Codes &
Color Names
(Continued)