2000 TOYOTA CAMRY codes

Toyota Supports ASE CertificationPage 1 of 2
EG001±00
Title:
SINGLE CYLINDER MISFIRES
Models:
'99 Avalon, Camry, Sienna & Solara (CA Spec.)
Technical Service
BULLETIN
January 14, 2000

NOTE:
The information contained in this TSB updates EG013±99 dated December 17, 1999.
Some 1999 California Emission Specification Avalon, Camry (1MZ±FE), Sienna & Solara
(1MZ±FE) vehicles may exhibit a rough idle, and or a M.I.L. ªONª condition, in which a
single cylinder misfire code, or codes are present. Changes have been made in the fuel
injector production process to correct this condition.
1999 CA Emission Spec. TMMK produced Avalon, Camry (1MZ±FE), Sienna &
TMMC produced Solara (1MZ±FE) vehicles built between the VIN numbers listed
below.
MODELSTARTING VINENDING VIN
Avalon4T1BF1#B*XU2985044T1BF1#B*XU319557
Camry4T1BF2#K*XU0764034T1BF2#K*XU081214
Camry (cont.)4T1BF2#K*XU9300244T1BF2#K*XU931330
Sienna4T3ZF1#C*XU0908874T3ZF1#C*XU122589
Solara (U.S.)2T1CF2#P*XC1110832T1CF2#P*XC757508
Solara (Canada)2T1CF2#P*XC7441132T1CF2#P*XC162681
APPLICABLE PARTSQUANTITYPART NAME
23209±0A0106Fuel Injector
OP CODEVWCDESCRIPTIONTIMEOPNT1T2
895221NR & R Fuel Injector Assembly ± All1.823209±0A0100256
Applicable Warranty*:
This repair is covered under the Toyota Federal Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
Coverage is extended to 36 months or 50,000 miles, whichever occurs first, in the
states of California, Massachusetts, and Vermont due to state emission warranty
legislation.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
NOTE:
Be sure to enter the DTC No. in the Condition/Cause/Remedy section, if a DTC Code
appeared.
ENGINE
Introduction
Applicable
Vehicles
Parts
Information
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 23
EG003-02Title:
READINESS MONITOR DRIVE PATTERNS
Models:
All '96 ± '02
Technical Service
BULLETIN
March 29, 2002

TSB REVISION NOTICE:
The information updated in this TSB is red
and underlined.
The On±Board Diagnostic (OBDII) system is designed to monitor the performance of
emission±related components and report any detected abnormalities in the form of
Diagnostic Trouble Codes (DTCs). Since the various components need to be monitored
during different driving conditions, the OBDII system is designed to run separate
monitoring programs called Readiness Monitors. Many state Inspection and
Maintenance (I/M) programs require that vehicles complete their Readiness Monitors
prior to beginning an emissions test.
The current status of the Readiness Monitors can be seen by using the Toyota Diagnostic
Tester with version 9.0 software (or newer), or a generic OBDII Scantool.
To view the Readiness Monitor status using the Toyota Diagnostic Tester, select ªMonitor
Statusº from the Enhanced OBDII Menu.
A status of ªcompleteº indicates that the necessary conditions have been met to run the
performance tests for the related Readiness Monitor.
The Readiness Monitor will be reset to ªincompleteº if:

ECU has lost power (battery or fuse).

DTCs have been cleared.

The conditions for running the Readiness Monitor have not been met.
In the event that any Readiness Monitor shows ªincomplete,º follow the appropriate
Readiness Monitor Drive Pattern to change the readiness status to ªcomplete.º
Refer to the Readiness Monitor Drive Pattern Application Table to determine which
drive pattern should be followed.
SECTIONPAGE(S)
Readiness Monitor Drive Pattern Application Tables3±9
Readiness Monitor Drive Patterns
1EGR Monitor (All Except 1FZ±FE Engine)10
2EGR Monitor (For 1FZ±FE Engine)11
3Catalyst Monitor (O2S Type)12
4Catalyst Monitor (AF Sensor Type)13
5EVAP Monitor (Internal Pressure Monitor/Non±Intrusive Type)14±15
6EVAP Monitor (Vacuum Pressure Monitor/Intrusive Type)16±17
7EVAP Monitor (Without Leak Detection)18
8EVAP Monitor (For Prius)19±20
9Oxygen Sensor Monitor (Front and Rear O2S System)21
10Oxygen/AF Sensor Monitor (Front AF Sensor and Rear O2S System)22
11Oxygen/AF Sensor Heater Monitor23

All 1996 ± 2002 model year Toyota vehicles.
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty±±±±
ENGINE
Introduction
Contents
Applicable
Vehicles
Warranty
Information

READINESS MONITOR DRIVE PATTERNS ± EG003-02 RevisedMarch 29, 2002
Page 10 of 23
DRIVE PATTERN NO. 1: EGR Monitor (All Except 1FZ±FE Engine)
Warm up
10 min
43 ± 56 mph
(70 ± 90 km/h)
Idling
IG SW off
3 ± 5 min 3 ± 5 min3 ± 5 min
(b)3 ± 5 min
(c)
(d) (a)
Preconditions
The monitor will not run unless:

MIL is OFF.

Altitude is 7800 feet (2400 m) or less.

IAT (Intake Air) is 14F (±10C) or greater.
Drive Pattern Procedure
Connect the OBDII Scantool to the DLC3 connector to check monitor status and
preconditions.
a. If IAT (Intake Air) is less than 50F (10C) when starting the engine, idle the
engine for approximately 10 minutes.
b. Drive the vehicle at 43 ± 56 mph (70 ± 90 km/h) for a period of 3 ± 5 minutes.
NOTE:

Do not allow the Throttle Position (TP) to exceed 30%.

Drive with smooth throttle operation and avoid sudden acceleration.
c. Stop the vehicle and let the engine idle for 3 ± 5 minutes.
d. Repeat steps ªbº and ªcº once.
If readiness status does not switch to ªcomplete,º ensure preconditions are met, turn the
ignition OFF, then repeat steps ªbº through ªd.º
NOTE:
The readiness status may not switch to ªcompleteº after the first drive pattern trip if a
Pending Code has been set (first trip for a two±trip DTC).

Pending Codes are available from the DTC Info Menu in Enhanced OBDII.

Pending Codes indicate a POTENTIAL problem was detected. A second trip is
needed to confirm the DTC prior to diagnosis.

Once a second trip is completed, a current DTC will be stored. Readiness
Monitor
Drive
Patterns:
EGR Monitors

READINESS MONITOR DRIVE PATTERNS ± EG003-02 RevisedMarch 29, 2002
Page 11 of 23
DRIVE PATTERN NO. 2: EGR Monitor (for 1FZ±FE Engine)
43 ± 56 mph
(70 ± 90 km/h)
Idling
IG SW off
3 ± 5 min 3 ± 5 min
3 ± 5 min
(b)3 ± 5 min
(c) (a)
Preconditions
The monitor will not run unless:

MIL is OFF.

Altitude is 7800 feet (2400 m) or less.

IAT (Intake Air) is 14F (±10C) or greater.

ECT (Coolant Temp) is less than 104F (40C).
Drive Pattern Procedure
Connect the OBDII Scantool to DLC3 to check monitor status and preconditions.
a. Start the engine and as soon as safely possible begin driving the vehicle at 43 ±
56 mph (70 ± 90 km/h) for a period of 3 ± 5 minutes.
NOTE:

Do not allow the Throttle Position (TP) to exceed 30%.

Drive with smooth throttle operation and avoid sudden acceleration.
b. Stop the vehicle and let the engine idle for 3 ± 5 minutes.
c. Repeat steps ªaº and ªbº once.
If readiness status does not switch to ªcomplete,º ensure preconditions are met, turn the
ignition OFF, then repeat steps ªaº through ªc.º
NOTE:
The readiness status may not switch to ªcompleteº after the first drive pattern trip if a
Pending Code has been set (first trip for a two±trip DTC).

Pending Codes are available from the DTC Info Menu in Enhanced OBDII.

Pending Codes indicate a POTENTIAL problem was detected. A second trip is
needed to confirm the DTC prior to diagnosis.

Once a second trip is completed, a current DTC will be stored. Readiness
Monitor
Drive
Patterns:
EGR Monitors
(Continued)

READINESS MONITOR DRIVE PATTERNS ± EG003-02 RevisedMarch 29, 2002
Page 12 of 23
DRIVE PATTERN NO. 3: Catalyst Monitor (O2S Type)
40 ± 50 mph
(64 ± 88 km/h)
35 ± 45 mph
(56 ± 72 km/h)
Idling
IG SW off
Warm up
ECT.176FIAT < 50F = 7 min
IAT > 50F = 3 min
(a)7 min
(b)
Preconditions
The monitor will not run unless:

MIL is OFF.

ECT (Coolant Temp) is 176F (80C) or greater.

IAT (Intake Air) is 14F (±10C) or greater.*
* For 2002 MY and later vehicles: The readiness test can be completed in cold ambient conditions
(less than 14F / ±10C), if the drive pattern is repeated a second time after cycling the ignition OFF.
Drive Pattern Procedure
Connect the OBDII Scantool to DLC3 to check monitor status and preconditions.
Note the IAT (Intake Air) value during engine startup. The driving time must be adjusted
during step ªaº based upon IAT (Intake Air) value at startup.
a. Drive the vehicle at 40 ± 55 mph (64 ± 88 km/h) for the time described below:

If IAT (Intake Air) was less than 50F (10C) when the engine was started,
drive for 7 minutes.

If IAT (Intake Air) was greater than 50F (10C) when the engine was started,
drive for 3 minutes.
b. Drive the vehicle at 35 ± 45 mph (56 ± 72 km/h) for approximately 7 minutes.
NOTE:

Drive with smooth throttle operation.

Avoid sudden acceleration.

Avoid sudden deceleration as much as possible with the throttle fully closed.
If readiness status does not switch to ªcomplete,º ensure preconditions are met, turn the
ignition OFF, then repeat steps ªaº and ªb.º
NOTE:
The readiness status may not switch to ªcompleteº after the first drive pattern trip if a
Pending Code has been set (first trip for a two±trip DTC).

Pending Codes are available from the DTC Info Menu in Enhanced OBDII.

Pending Codes indicate a POTENTIAL problem was detected. A second trip is
needed to confirm the DTC prior to diagnosis.

Once a second trip is completed, a current DTC will be stored. Readiness
Monitor
Drive
Patterns:
Catalyst
Monitors

READINESS MONITOR DRIVE PATTERNS ± EG003-02 RevisedMarch 29, 2002
Page 13 of 23
DRIVE PATTERN NO. 4: Catalyst Monitor (AF Sensor Type)
IAT < 50F = 7 min
IAT > 50F = 3 min
(a)
40 ± 50 mph
(64 ± 88 km/h)
Idling
IG SW off
16 min
(b) 35 ± 45 mph
(56 ± 72 km/h)
Warm up
ECT.176F
Preconditions
The monitor will not run unless:

MIL is OFF.

ECT (Coolant Temp) is 176F (80C) or greater.

IAT (Intake Air) is 14F (±10C) or greater.*
* For 2002 MY and later vehicles: The readiness test can be completed in cold ambient conditions
(less than 14F / ±10C), if the drive pattern is repeated a second time after cycling the ignition OFF.
Drive Pattern Procedure
Connect the OBDII Scantool to DLC3 to check monitor status and preconditions.
Note the IAT (Intake Air) value during engine startup. The driving time must be adjusted
during step ªaº based upon IAT (Intake Air) value at startup.
a. Drive the vehicle at 40 ± 55 mph (64 ± 88 km/h) for the time described below:

If IAT (Intake Air) was less than 50F (10C) when the engine was started,
drive for 7 minutes.

If IAT (Intake Air) was greater than 50F (10C) when the engine was started,
drive for 3 minutes.
b. Drive the vehicle allowing speed to fluctuate between 35 ± 45 mph (56 ± 72 km/h)
for about 16 minutes.
NOTE:

Drive with smooth throttle operation.

Avoid sudden acceleration.

Avoid sudden deceleration as much as possible with the throttle fully closed.
If readiness status does not switch to ªcomplete,º ensure preconditions are met, turn the
ignition OFF, then repeat steps ªaº and ªb.º
NOTE:
The readiness status may not switch to ªcompleteº after the first drive pattern trip if a
Pending Code has been set (first trip for a two±trip DTC).

Pending Codes are available from the DTC Info Menu in Enhanced OBDII.

Pending Codes indicate a POTENTIAL problem was detected. A second trip is
needed to confirm the DTC prior to diagnosis.

Once a second trip is completed, a current DTC will be stored. Readiness
Monitor
Drive
Patterns:
Catalyst
Monitors
(Continued)

READINESS MONITOR DRIVE PATTERNS ± EG003-02 RevisedMarch 29, 2002
Page 15 of 23
Drive Pattern Preconditions
The monitor will not run unless:

MIL is OFF.

Fuel level is between 1/2 to 3/4 full (for faster completion)
.

Altitude is 7800 feet (2400 m) or less.

ECT (Coolant Temp) is between 40F and 95F (4.4C ± 35C).

IAT (Intake Air) is between 40F and 95F (4.4C ± 35C).

Cold Soak Procedure has been completed.
NOTE:
Before starting the engine, the difference between ECT (Coolant Temp) and IAT (Intake
Air) must be less than 13F (7C). (Refer to Examples 1 and 2 on previous page.)
Drive Pattern Procedure

Connect the OBDII Scantool to DLC3 to check monitor status and preconditions.

Release the pressure in the fuel tank by removing and then reinstalling the fuel tank
cap.

Start the engine and begin driving as directed.
NOTE:

Do not turn the ignition off until the drive pattern is complete.

Drive on smooth roads to reduce excessive fuel sloshing.
2a. Start the engine and as soon as safely possible begin driving at approximately 45
mph (72km/h) for 5 minutes. (See illustration on previous page.)
2b. Drive the vehicle at approximately 25 mph (40 km/h) for 15 minutes and include a
minimum of two stops for approximately 30 seconds. (See illustration on previous
page.)
The monitor should complete within approximately 20 minutes. If it does not, ensure
preconditions are met and repeat the drive pattern process beginning with the Cold Soak
Procedure.
NOTE:
The readiness status may not switch to ªcompleteº after the first drive pattern trip if a
Pending Code has been set (first trip for a two±trip DTC).

Pending Codes are available from the DTC Info Menu in Enhanced OBDII.

Pending Codes indicate a POTENTIAL problem was detected. A second trip is
needed to confirm the DTC prior to diagnosis.

Once a second trip is completed, a current DTC will be stored. Readiness
Monitor
Drive
Patterns:
EVAP
Monitors
(Continued)

READINESS MONITOR DRIVE PATTERNS ± EG003-02 RevisedMarch 29, 2002
Page 17 of 23
Drive Pattern Preconditions
The monitor will not run unless:

MIL is OFF.

Fuel level is between 1/2 to 3/4 full (for faster completion)
.

Altitude is 7800 feet (2400 m) or less.*

ECT (Coolant Temp) is between 40F and 95F (4.4C ± 35C).

IAT (Intake Air) is between 40F and 95F (4.4C ± 35C).*

Cold Soak Procedure has been completed.
* For 2002 MY and later vehicles: The readiness test can be completed in cold ambient conditions
(less than 40F / 4.4C) and/or at high altitudes (more than 7800 feet / 2400 m) if the complete drive
pattern (including Cold Soak) is repeated a second time after cycling the ignition OFF.
NOTE:
Before starting the engine, the difference between ECT (Coolant Temp) and IAT (Intake
Air) must be less than 13F (7C). (Refer to Examples 1 and 2 on previous page.)
Drive Pattern Procedure

Connect the OBDII Scantool to DLC3 to check monitor status and preconditions.

Release the pressure in the fuel tank by removing and then reinstalling the fuel tank
cap.
2a. Start the engine and allow it to idle until ECT (Coolant Temp) is 167F (75C) or
greater. (See illustration on previous page.)
2b. Race the engine at 3,000 rpm for approximately 10 seconds. (See illustration on
previous page.)
2c. Allow the engine to idle with the A/C ON (to create a slight load) for 15 ± 50
minutes. (See illustration on previous page.)
NOTE:
If the vehicle is not equipped with A/C put a slight load on the engine by doing the
following:

Securely set the parking brake.

Block the drive wheels with wheel chocks.

Allow the vehicle to idle in drive for 15 ± 50 minutes.
NOTE:
The readiness status may not switch to ªcompleteº after the first drive pattern trip if a
Pending Code has been set (first trip for a two±trip DTC).

Pending Codes are available from the DTC Info Menu in Enhanced OBDII.

Pending Codes indicate a POTENTIAL problem was detected. A second trip is
needed to confirm the DTC prior to diagnosis.

Once a second trip is completed, a current DTC will be stored. Readiness
Monitor
Drive
Patterns:
EVAP
Monitors
(Continued)