2000 TOYOTA CAMRY steering wheel

MA00N±01
N01022
± MAINTENANCECHASSIS
MA±7
50 Author: Date:
CHASSIS
INSPECTION
1. INSPECT STEERING LINKAGE
(a) Check the steering wheel freeplay. (See page SR±8)
(b) Check the steering linkage for looseness or damage.
Check that:

Tie rod ends do not have excessive play.

Dust seals and boots are not damaged.

Boot clamps are not loose.
2. INSPECT SRS AIRBAG (See page RS±2)
3. INSPECT STEERING GEAR HOUSING OIL
Check the steering gear housing for oil leakage.
4. INSPECT DRIVE SHAFT BOOTS
Check the drive shaft boots for clamp looseness, leakage or
damage.
5. INSPECT BALL JOINTS AND DUST COVERS
(a) Inspect the ball joints for excessive looseness.

Jack up the front of the vehicle and place wooden
blocks with a height of 180 ± 200 mm (7.09 ± 7.87
in.) under the front tires.

Lower the jack until there is about half a load on the
front coil spring. Place stands under the vehicle for
safety.

Check that the front wheels are pointing straight
ahead, and block them with chocks.

Using a lever, pry up the end of the lower arm, and
check the amount of play.
Maximum ball joint vertical play: 0 mm (0 in.)
If there is play, replace the ball joint.
(b) Check the dust cover for damage.
6. CHECK TRANSAXLE OIL (FLUID)
(a) Visually check the transaxle for oil (fluid) leakage.
If leakage is found, check for the cause and repair.
7. REPLACE TRANSAXLE OIL (FLUID)
(a) M/T:
Replace the transaxle oil.
S51: (See page MX±4)
E153: (See page MX±4)
(b) A/T:
Replace the transaxle fluid.
A140E: (See page DI±389)
A541E: (See page DI±438)

± MAINTENANCEBODY
MA±9
52 Author: Date:

Check that the brakes work properly and do not
drag.

Do setting of the parking brake shoes and drum.
(c) Be sure to deliver a clean car. Especially check:

Steering wheel

Shift lever knob

All switch knobs

Door handles

Seats

MX04Z±01
Q09981
Hood
14 (150, 10)
w/ Cruise Control :
Cruise Control Actuator
12 (120, 9)
Clutch Line Bracket
21 (210, 15)
12 (120, 9)
Clutch Release Cylinder
26 (270, 20)
RH Drive Shaft


32 (330, 24)
7.8 (80, 69 in.´lbf)
Flywheel Housing Under CoverRH Fender
Apron SealClutch Accumulator
Vehicle Speed Sensor
Connector
46 (470, 34)
Engine LH Mounting
Insulator with Bracket
Rear RH Suspension Member Brace
37 (380, 27)
Transaxle
64 (650, 47)
36 (370, 27)
10 (100, 7)
Steering Return Pipe
19 (195, 14)
32 (330, 24)
181 (1,850, 134)
Silver Bolt : 44 (450, 33)
Green Bolt : 66 (670, 48)
Suspension Member with
Lower Suspension Arm
Front RH Suspension
Member Brace
181 (1,850, 134)
Control
Cable
Clip13 (130, 9)
Clip
Washer
Starter
21 (210, 15)
39 (400, 29)
Air Cleaner
Case Assembly
with Air Hose
64 (650, 47)Ground Cable
x5Back±Up Light Switch Connector
Engine Wire
20 (200, 14)Hold±Down
Clamp
Battery
LH Drive Shaft
LH Fender Apron Seal RH Exhaust Manifold Stay
64 (650, 47)
181 (1,850, 134)PS Gear Assembly
No.1 Fuel Tube Protector
49 (500, 36)
294 (3,000, 217)
Lock Cap
Rear LH Suspension Member Brace
Stabilizer Bar Link
Hole
Plug
127 (1,300, 94)
39 (400, 29)
80 (820, 59)48 (490, 35)
Silver Bolt : 44 (450, 33)
Green Bolt : 66 (670, 48)
Front LH Suspension
Member Brace RH Fender
Liner
Engine Rear Side
Shutter Plate
56 (570, 41)




62 (630, 46)

62 (630, 46)

Front Exhaust Pipe
No.1 Exhaust Pipe
Support Bracket
33 (330, 24)
Exhaust Pipe Support Stay
33 (330, 24)LH Fender
Liner
66 (670, 48)
Snap Ring

Snap Ring

Cotter Pin

Cotter Pin

Gasket

Gasket

Gasket
Non±reusable part: Specified torque
N´m (kgf´cm, ft´lbf)


36 (370, 27)
± MANUAL TRANSAXLE (E153)MANUAL TRANSAXLE UNIT
MX±3
1804 Author: Date:
MANUAL TRANSAXLE UNIT
COMPONENTS

Q09994
Q09995
Q09996
CA
C
A
CB
AAB
C
Q09997
14 mm Head B14 mm Head B
14 mm Head A
± MANUAL TRANSAXLE (E153)MANUAL TRANSAXLE UNIT
MX±7
1808 Author: Date:
21. REMOVE LH ENGINE MOUNTING INSULATOR WITH
BRACKET
(a) Remove the 2 hole plugs, nuts and 3 bolts.
Torque:
Bolt: 64 N´m (650 kgf´cm, 47 ft´lbf)
Nut: 80 N´m (820 kgf´cm, 59 ft´lbf)
(b) Lift up the transaxle and remove the left engine mounting
insulator with the bracket.
22. REMOVE HOLE PLUG AND 4 ENGINE REAR SIDE
MOUNTING NUTS
Torque: 66 N´m (670 kgf´cm, 48 ft´lbf)
23. ATTACH ENGINE SLING DEVICE TO ENGINE HANG-
ER
(See page EM±69)
24. DISCONNECT STEERING RETURN PIPE FROM
FRONT SUSPENSION MEMBER
Remove the 2 bolts.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
25. REMOVE FRONT SUSPENSION MEMBER WITH LOW-
ER SUSPENSION ARM
(a) Remove the LH and RH fender liner set screws.
(b) Remove the 6 bolts, 4 nuts, front LH and RH suspension
member braces, rear LH and RH suspension member
braces and front suspension member with the lower sus-
pension arm.
Torque:
Bolt A: 181 N´m (1,850 kgf´cm, 134 ft´lbf)
Bolt B: 32 N´m (330 kgf´cm, 24 ft´lbf)
Nut C: 36 N´m (370 kgf´cm, 27 ft´lbf)
26. JACK UP TRANSAXLE SLIGHTLY
Using a transmission jack, support the transaxle.
27. REMOVE FLYWHEEL HOUSING UNDER COVER AND
TRANSAXLE LOWER SIDE MOUNTING BOLT
(a) Remove the 2 bolts and cover.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
(b) Remove the 3 bolts of the transaxle lower side.
Torque:
14 mm head A: 46 N´m (470 kgf´cm, 34 ft´lbf)
14 mm head B: 37 N´m (380 kgf´cm, 27 ft´lbf)

PP0KZ±01
PP±102
± PREPARATIONBODY ELECTRICAL
154 Author: Date:
RECOMMENDED TOOLS
09082±00040TOYOTA Electrical Tester.
09041±00030Torx Driver T30 .For removing and installing
steering wheel pad
09042±00010Torx Socket T30 .For removing and installing
steering wheel pad

SS09P±01
SS±48
± SERVICE SPECIFICATIONSMANUAL TRANSAXLE (E153)
211 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Transaxle x Engine 17 mm head
14 mm head A
(See page MX±4) 14 mm head B64
46
37650
470
38047
34
27
Cruise control actuator x Body (w/ Cruise control)131309
Starter x Transaxle3940029
Clutch release cylinder x Transaxle121209
Clutch acummulator x Transaxle Bolt
Nut21
26210
27015
20
Clutch line bracket x Transaxle121209
Front wheel1031,05076
Exhaust pipe support stay3333024
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Center exhaust pipe5657041
No.1 exhaust pipe support bracket x Front suspension member3333024
Stabilizer bar link x Stabilizer bar3940029
Stabilizer bar bracket x Front suspension member1919514
PS gear assembly x Front suspension member1811,850134
Front engine absorber x Transaxle4849035
RH exhaust manifold stay2020014
Front engine mounting insulator x Front suspension member Silver bolt
Green bolt44
66450
67033
48
LH engine mounting insulator x Front suspension member8082059
LH engine mounting bracket x Transaxle6465047
Rear engine mounting insulator x Front suspension member6667048
Steering return pipe x Front suspension member101007
Front suspension member with lower suspension arm Bolt A
Bolt B
(See page MX±4) Nut C181
32
361,850
330
370134
24
27
Flywheel housing under cover x Transaxle7.88069 in.´lbf
Shift cable grommet retainer x Body4.95043 in.´lbf
Shift lever assembly x Body121209
No.2 selecting bellcrank with selecting bellcrank support2020014
Shift and select lever shaft lock bolt4950036
Shift and select lever shaft assembly x Transmission case2020014
Transmission case cover x Transmission case2930022
Breather plug4950036
Output shaft lock nut1231,25090
Shift fork and shift head set bolt2424017
Rear bearing retainer x Transmission case4243031
Straight screw plug2525018
Straight screw plug (Reverse restrict pin)131309
Reverse idler gear shaft lock bolt2930022
Transmission case x Transaxle case2930022
Transmission oil pipe x Transaxle case1717513
Reverse shift arm bracket assembly x Transaxle case1717513

SS09N±01
SS±52
± SERVICE SPECIFICATIONSMANUAL TRANSAXLE (S51)
215 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Transaxle x Engine 17 mm head6465047Transaxle x Engine 17 mm head
14 mm head
64
46
650
470
47
34
Cruise control actuator x Body (w/ Cruise control)131309
Starter x Transaxle3737828
Clutch release cylinder x Transaxle121209
Clutch line bracket x Transaxle Bolt A121209Clutch line bracket x Transaxle Bolt A
(See page MX±4) Bolt B
12
6.9
120
70
9
61 in.´lbf
Manifold stay Front side4242531
Manifold stay Rear side3940029
Front wheel1031,05076
Exhaust pipe bracket Bolt1919514Exhaust ie bracket Bolt
Nut
19
33
195
330
14
24
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Center exhaust pipe5657041
No.1 exhaust pipe support bracket x Front suspension member3333024
Stabilizer bar link x Stabilizer bar3940029
Stabilizer bar bracket x Front suspension member1919514
PS gear assembly x Front suspension member1811,850134
Front engine mounting insulator x Front suspension member Silver bolt4445033Front engine mounting insulator x Front sus ension member Silver bolt
Green bolt
44
66
450
670
33
48
LH engine mounting insulator x Front suspension member8082059
LH engine mounting bracket x Transaxle6465047
Rear engine mounting insulator x Front suspension member6667048
Steering return pipe x Front suspension member101007
Front suspension member with lower suspension arm Bolt A1811,850134Front sus ension member with lower sus ension arm Bolt A
Bolt B
181
32
1,850
330
134
24Bolt B
(See page MX±4) Nut C
32
36
330
370
24
27
LH stiffener plate3738027
RH stiffener plate3940029
Rear end plate9.39582 in.´lbf
Shift cable grommet retainer x Body4.95043 in.´lbf
Shift lever assembly x Body121209
Transmission case x Transaxle case2930022
Transmission case x Case cover2930022
Transmission case protector1818513
Rear bearing retainer4243031
Output shaft front bearing lock plate1818513
Transaxle case receiver set bolt7.47565 in.´lbf
5th driven gear lock nut1231,25090
Reverse idler shaft lock bolt2930022
Control shaft cover3737527
Control shift lever x Lever shaft6.46556 in.´lbf
Ring gear x Differential case8385061
Selecting bellcrank x Transmission case3738027

SS04W±01
± SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS±59
222 Author: Date:
SUSPENSION AND AXLE
SERVICE DATA
P195/70R14 90SFront, Rear*1210 kPa (2.1 kgf/cm2, 30 psi)
Cold tire inflationP195/70R14 90SFront, Rear*2210 kPa (2.1 kgf/cm2, 30 psi)pressure
(Normal driving)P205/65R15 92HFront, Rear*1220 kPa (2.2 kgf/cm2, 32 psi)(Normal driving)P205/65R15 92HFront, Rear*2200 kPa (2.0 kgf/cm2, 29 psi)
P195/70R14 90SFront, Rear*3210 kPa (2.1 kgf/cm2, 30 psi)
Cold tire inflationP195/70R14 90SFront, Rear*4240 kPa (2.4 kgf/cm2, 35 psi)pressure
(Trailer towing)P205/65R15 92HFront, Rear*3220 kPa (2.2 kgf/cm2, 32 psi)(Trailer towing)P205/65R15 92HFront, Rear*4240 kPa (2.4 kgf/cm2, 35 psi)
V hi l h i ht 195/70R14Front*5212 mm (8.35 in.)Vehicle height195/70R14Rear*6264 mm (10.39 in.)
205/65R15Front*5215 mm (8.46 in.)205/65R15Rear*6266 mm (10.49 in.)
Camber 5S±FE±0°36'±45'(0.6°±0.75°)Camber 5S ± FE
1MZ ± FE
±036 ± 45 (0.6 ± 0.75)
±0°37' ± 45' (0.62° ± 0.75°)1MZ ± FE±037 ± 45 (0.62 ± 0.75)
Left ± right error45' (0.75°) or less
Front wheel
alignment
Caster 5S ± FE
1MZ ± FE
Left ± right error2°10' ± 45' (2.17° ± 0.75°)
2°11' ± 45' (2.18° ± 0.75°)
45' (0.75°) or less
alignmentSteering axis inclination 5S ± FE
1MZ ± FE
Left ± right error13°01' ± 45' (13.02° ± 0.75°)
13°04' ± 45' (13.07° ± 0.75°)
45' (0.75°) or less
Toe±in (Total)
Rack end length difference0° ± 12' (0° ± 0.2°)
0 ± 2 mm (0 ± 0.08 in.)
1.5 mm (0.059 in.) or less
Wh l l 195/70R14Inside wheel 37°12' ± 2° (37.2° ± 2°)Wheel angle195/70R14Outside wheel 32°21' (32.45°)
205/65R15Inside wheel 35°47' ± 2° (35.78° ± 2°)205/65R15Outside wheel 31°25' (31.42°)
Rear wheel
li t
Camber 5S ± FE
1MZ ± FE
Left ± right error±0°42' ± 45' (±0.7° ± 0.75°)
±0°45' ± 45' (±0.75° ± 0.75°)
45' (0.75°) or less
alignmentToe±in (Total)
No.2 lower suspension arm length difference0°24' ± 12' (0.4° ± 0.2°)
4 ± 2 mm (0.16 ± 0.08 in.)
1 mm (0.04 in.) or less
*1: For all loads including rated loads
*2: For reduced loads (1 to 4 passengers)
*3: For driving under 160 km/h (100 mph)
*4: For driving at 160 km/h (100 mph) or over
*5: Front measuring point
Measure from the ground to the center of the front side lower suspension arm mounting bolt.
*6: Rear measuring point
Measure from the ground to the center of the strut rod mounting bolt.