2000 TOYOTA CAMRY power steering

SR06Y±01
W04224
SST
Fulcrum
Length
± STEERINGPOWER STEERING GEAR
SR±49
2144 Author: Date:
INSTALLATION
1. INSTALL PS GEAR ASSEMBLY
(a) Install the gear assembly from the LH of the vehicle.
NOTICE:
Do not damage the turn pressure tubes.
(b) Torque the 2 gear assembly set bolts and nuts.
Torque: 181 N´m (1,850 kgf´cm, 134 ft´lbf)
HINT:
Lift up the stabilizer bar and install the bolts.
2. INSTALL NO.1 FUEL TUBE PROTECTOR
Install the 2 bolts and nut.
3. CONNECT STABILIZER BAR
Torque the 4 bolts.
Torque: 19 N´m (195 kgf´cm, 14 ft´lbf)
4. CONNECT PRESSURE FEED AND RETURN TUBES
Using SST, connect the tube.
SST 09631±22020
Torque: 32 N´m (326 kgf´cm, 24 ft´lbf)
HINT:

Use a torque wrench with a fulcrum length of 300 mm
(11.81 in.).

This torque value is effective in case that SST is parallel
to a torque wrench.
5. CONNECT CLAMP PLATE
Torque the nut.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
6. CONNECT INTERMEDIATE SHAFT ASSEMBLY
(See page SR±16)
7. CONNECT RH AND LH TIE ROD ENDS
(See page SA±10)
8. POSITION FRONT WHEELS FACING STRAIGHT
AHEAD
HINT:
Do it with the front of the vehicle jacked up.
9. CENTER SPIRAL CABLE
(See page SR±16)
10. INSTALL STEERING WHEEL
(a) Install the wheel at straight±ahead position.
(b) Temporarily tighten the wheel set nut.
(c) Connect the connector.
11. BLEED POWER STEERING SYSTEM
(See page SR±4)
12. CHECK STEERING WHEEL CENTER POINT

SR±50
± STEERINGPOWER STEERING GEAR
2145 Author: Date:
13. TORQUE STEERING WHEEL SET NUT
Torque: 35 N´m (360 kgf´cm, 26 ft´lbf)
14. INSTALL STEERING WHEEL PAD
(See page SR±16)
15. CHECK FRONT WHEEL ALIGNMENT
(See page SA±4)

WARRANTY PARTS MARKING PROCEDURE ± PG006-03September 26, 2003
Page 2 of 3
Dealers are requested to mark the location of the failure of all warranty parts that are
listed below.
This list is not inclusive. There may be other components that can be
marked in the area of failure. All other parts that can be marked should be marked.
assist grip assy headlamps
audio (blemish) headliner
back door garnish hoses
bumper covers instrument panel safety pad sub±assy
cargo cover (retractable) Interior light assemblies and covers
carpet knobs, levers, handles
clutch disc l/pulley pump assy
clutch flywheel mirrors (side and rearview)
combination meter glass navigation or VES screens
console and components pillar garnish
cowl assy rack and pinion/power steering gear assy
cowl side trim sub±assy radiator
cupholders room partition board
cylinder head cover sub±assy rotors (mark where min. runout is exceeded or warped)
dash panel insulator assy seat covers/cushions
dashboard and trim seat tracks
disc wheel soft trim
display panels spare tire cover
door handle assy steering column cover
door moulding steering wheel
door trim panel & molding tail lamps and covers
emblems transmission oil pan
engine oil pan visor
exhaust manifold washer jar
floor and cargo mats wheel cap
gear shift knob wheels
grills
Parts
Marking
Requirement
Parts
Marking
List

Page 1 of 1Toyota Supports ASE Certification
ST004±00Title:
STEERING RACK END NOISE
Models:
'97 ± '00 Camry (NAP) & '99 ± '00 Solara
Technical Service
BULLETIN
June 16, 2000

Some 1997 ± 2000 model year Camry (NAP) and 1999 ± 2000 Solara vehicles may
experience a squeaking noise from the front suspension. To improve this condition,
production parts have been changed.
1997 ± 2000 model year Camry (North American Produced)
1999 ± 2000 model year Solara
MODELSTARTING VIN
NAP Camry
4T1BG2*K*YU668756
4T1BG2*K*YU986504
4T1BF2*K*YU104860
4T1BF2*K*YU947590
Solara2T1C*2*P*YC359722
MODELPREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
Camry
and
Solara
45503±09030
or
45503±39055
or
45503±39135
45503±39135Steering Rack End
Sub±Assembly
HINT:
A quick reference in differentiating
between the previous and new parts is
that the previous Rack End Shaft is
BLACK and the current part is GRAY.Previous Part (BLACK SHAFT)
Current Part (GRAY SHAFT)
OP CODEDESCRIPTIONTIMEOPNT1T2
444631R & R Power Steering Rack End
Sub±Assembly (One Side)2.2
45503±09030
or
45503±39055
9199
Combo Code AOther Side0.5
45503 39055
or
45503±39135
9199
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
STEERING
Introduction
Applicable
Vehicles
Production
Change
Information
Parts
Information
Warranty
Information

Page 1 of 1Toyota Supports ASE Certification
ST008-01Title:
STEERING RACK END NOISE
Models:
'97 ± '00 Camry (NAP) & '99 ± '00 Solara
Technical Service
BULLETIN
December 21, 2001

TSB Update Notice:
The information contained in this TSB updates ST004±00 dated June 16, 2000.
Revised text is red
and underlined.
Some 1997 ± 2000 model year Camry (NAP) and 1999 ± 2000 Solara vehicles may
experience a squeaking noise from the front suspension. To improve this condition,
production parts have been changed.
1997 ± 2000 model year Camry (North American Produced) vehicles.
1999 ± 2000 model year Solara vehicles.
MODELSTARTING VIN
NAP Camry
4T1BG2#K#YU668756
4T1BG2#K#YU986504
4T1BF2#K#YU104860
4T1BF2#K#YU947590
Solara2T1C#2#P#YC359722
MODELPREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
Camry
and
Solara
45503±09030
or
45503±39055
or
45503±39135
45503±39135Steering Rack End
Sub±Assembly
NOTE:
Current service parts may be GRAY or BLACK in color.
OP CODEDESCRIPTIONTIMEOPNT1T2
444631R & R Power Steering Rack End
Sub±Assembly (One Side)2.245503±09030
or
45503±39055
9199
Combo Code AOther Side0.5
45503 39055
or
45503±39135
9199
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
STEERING
Introduction
Applicable
Vehicles
Production
Change
Information
Parts
Information
Warranty
Information