2000 CHRYSLER CARAVAN Service Manual

TEST TC-20BREPAIRING - BRAKE SWITCH PLAUSIBILITY WITH REDUNDANT CONTACT
Perform TEST TC-20A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST
TC-20B. TURN IGNITION OFF.
DISCONNECT THE KEY ON. USING A
BRAKE LAMP SWITCH VOLTMETER, MEASURE IS THE VOLTAGE NO CONTINUE TEST
HARNESS HARNESS CONNECTOR ABOVE 9.0 VOLTS? TC-20B ON THE
CONNECTOR.** CAVITY 1. NEXT PAGE.
FIG.1
YES
CONNECT A FUSEDREPAIR THE
JUMPER WIRE (5 AMP),YES SECONDARY BRAKE SW
ACROSS BRAKE LAMP CHECK THE FUSE. DID FUSE OPEN? SENSE CIRCUIT FOR
SWITCH HARNESS CONN A SHORT TO
CAVITIES 1 AND 2. VOLTAGE.*
NO
DID THE DRB
DISPLAY CHANGE YES ADJUST OR REPLACE
FROM "PRESSED" TO THE BRAKE LAMP
"RELEASED"? SWITCH.*
NO
KEY OFF. BRAKE LAMP SWITCH REPAIR THE OPEN
USING AN OHMMETER, HARNESS CONNECTOR IS THE RESISTANCE NO SECONDARY BRAKE
MEASURE THE CAVITY 2 AND GROUND. BELOW 5.0 OHMS? LAMP SWITCH GROUND
RESISTANCE CIRCUIT.*
BETWEEN... FIG.1
YES
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
91
ProCarManuals.com

TEST TC-20BCONTINUED - REPAIRING - BRAKE SWITCH PLAUSIBILITY WITH REDUNDANT
CONTACT
FIG.1
FIG. 2
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
92
ProCarManuals.com

TEST TC-20BCONTINUED - REPAIRING - BRAKE SWITCH PLAUSIBILITY WITH REDUNDANT
CONTACT
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-20B KEY OFF.
CONTINUED FROM DISCONNECT THE ECM
THE PREVIOUS HARNESS
PAGE. CONNECTORS.**
OF THE SECONDARY REPAIR OPEN IN THE
USING AN OHMMETER, BRAKE LAMP SWITCH IS THE RESISTANCE NO SECONDARY BRAKE
MEASURE THE SIGNAL CIRCUIT. BELOW 5.0 OHMS? LAMP SWITCH SIGNAL
RESISTANCE...CIRCUIT.*
FIG.1
YES
USING AN OHMMETER, THE BRAKE LAMP REPAIR SHORT TO
MEASURE THE SWITCH HARNESS IS THE RESISTANCE YES GROUND IN THE
RESISTANCE CONNECTOR CAVITY 1 BELOW 5.0 OHMS? SECONDARY BRAKE
BETWEEN... AND GROUND. LAMP SWITCH SIGNAL
FIG.2 CIRCUIT.*
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
93
ProCarManuals.com

TEST TC-21AREPAIRING - CLUTCH SIGNAL PLAUSIBILITY
Perform TEST DTC Before Proceeding
FIG.1
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
94
ProCarManuals.com

TEST TC-21AREPAIRING - CLUTCH SIGNAL PLAUSIBILITY
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST
TC-21A. TURN IGNITION ON.
WITH THE DRB, WHILE OBSERVING
MONITOR THE CLUTCH THE DISPLAY, PRESS DID THE DRB CHANGE NO CONTINUE TEST
PEDAL SWITCH AND RELEASE THE FROM "RELEASED" TO TC-21A ON THE
INPUT. CLUTCH PEDAL "PRESSED"? NEXT PAGE.
SEVERAL TIMES.
YES
THE CONDITION TO SET USING THE SCHEMATIC
THE TROUBLE CODE IS AS A GUIDE, INSPECT WERE ANY PROBLEMS YES REPAIR AS
NOT PRESENT. THE WIRING AND FOUND? NECESSARY.*
CONNECTORS.
FIG.1 FIG.2
NO
WIGGLE THE WIRING DID THE DRB REPAIR AS
HARNESS FROM THE DISPLAY CHANGE YES NECESSARY WHERE
CLUTCH PEDAL SWITCH FROM "RELEASED" TO THE WIGGLING
TO THE ENGINE "PRESSED"? CAUSED THE SWITCH
CONTROL MODULE.STATUS TO CHANGE.*
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETED.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
95
ProCarManuals.com

TEST TC-21ACONTINUED - REPAIRING - CLUTCH SIGNAL PLAUSIBILITY
FIG.1
FIG.2
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
96
ProCarManuals.com

TEST TC-21ACONTINUED - REPAIRING - CLUTCH SIGNAL PLAUSIBILITY
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-21A
CONTINUED FROM
THE PREVIOUS TURN IGNITION OFF.
PAGE.
DISCONNECT THE USING AN OHMMETER, REPAIR OPEN IN
CLUTCH PEDAL MEASURE THE CLUTCH IS THE RESISTANCE NO CLUTCH PEDAL
SWITCH HARNESS PEDAL SWITCH HARNESS BELOW 5.0 OHMS. SWITCH GROUND
CONNECTOR.** CONNECTOR CAVITY 2 CIRCUIT.*
AND GROUND. FIG.1
YES
WHILE OBSERVING THE CLUTCH PEDAL CHECK ADJUSTMENT OF
THE DRB, CONNECT A SWITCH HARNESS DID THE DRB CHANGE YES CLUTCH PEDAL SWITCH.
JUMPER WIRE CONNECTOR. FROM "RELEASED" TO IF ADJUSTMENT IS OK,
ACROSS... "PRESSED"? REPLACE THE CLUTCH
FIG.1 PEDAL SWITCH.*
NO
USING AN OHMMETER,
DISCONNECT THE ECM MEASURE CLUTCH PEDAL IS THE RESISTANCE NO REPAIR OPEN CLUTCH
HARNESS SWITCH SENSE CIRCUIT BELOW 5.0 OHMS? PEDAL SWITCH SENSE
CONNECTORS.** RESISTANCE. CIRCUIT.*
FIG.2
YES
ENGINE CONTROL REPAIR CLUTCH
USING AN OHMMETER MODULE HARNESS IS THE RESISTANCE NO PEDAL SWITCH SENSE
MEASURE RESISTANCE CONNECTOR CAVITY ABOVE 5.0 OHMS? CIRCUIT FOR SHORT
BETWEEN... 46 AND GROUND. TO GROUND.*
YES
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
97
ProCarManuals.com

TEST TC-22AREPAIRING - CONTROL SLEEVE SENSOR SIGNAL HIGH EXCEEDED
Perform TEST DTC Before Proceeding
FIG.1
FIG.2
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
98
ProCarManuals.com