Page 2925 of 4592

MA002±11
MA±2
± MAINTENANCEINSIDE VEHICLE
45 Author: Date:
INSIDE VEHICLE
GENERAL MAINTENANCE
These are maintenance and inspection items which are considered to be the owner's responsibility.
They can be done by the owner or they can have them done at a service shop.
These items include those which should be checked on a daily basis, those which, in most cases, do not
require (special) tools and those which are considered to be reasonable for the owner to do.
Items and procedures for general maintenance are as follows.
1. GENERAL NOTES
Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).
Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.
Failure to do even one item an cause the engine to run poorly and increase exhaust emissions.
2. LIGHTS
(a) Check that the headlights, stop lights, taillights, turn signal lights, and other lights are all working.
(b) Check the headlight aim.
3. WARNING LIGHTS AND BUZZERS
Check that all warning lights and buzzers function properly.
4. HORN
Check that it is working.
5. WINDSHIELD GLASS
Check for scratches, pits or abrasions.
6. WINDSHIELD WIPER AND WASHER
(a) Check operation of the wipers and washer.
(b) Check that the wipers do not streak.
7. WINDSHIELD DEFROSTER
Check that air comes out from the defroster outlet when operating the heater or air conditioner.
8. REAR VIEW MIRROR
Check that it is mounted securely.
9. SUN VISORS
Check that they move freely and are mounted securely.
10. STEERING WHEEL
Check that it has the specified freeplay. Be alert for changes in steering condition, such as hard steering,
excessive freeplay or strange noises.
11. SEATS
(a) Check that the seat adjusters operate smoothly.
(b) Check that all latches lock securely in any position.
(c) Check that the head restraints move up and down smoothly and that the locks hold securely in any
latch position.
(d) For fold±down seat backs, check that the latches lock securely.
12. SEAT BELTS
(a) Check that the seat belt system such as the buckles, retractors and anchors operate properly and
smoothly.
(b) Check that the belt webbing is not cut, frayed, worn or damaged.
Page 2982 of 4592
MX05K±01
Q10281
Shift Lever Knob
Center Console Upper Panel
Heater Control Assembly
Center Cluster
Finish Panel
Front Console Box
12 (120, 9)
Shift Lever Assembly
Clip
Washer Shift Control Cable
Select Control Cable Clip
Clip ClipClip
Clip
Clip Shift Cable Grommet Retainer
4.9 (50, 43 in.´lbf)Shift Cable
Grommet
Grommet Shift Cable Grommet
Retainer
4.9 (50, 43 in.´lbf)
Washer
Clip
N´m (kgf´cm, ft´lbf): Specified torqueRear Console Box
Washer
± MANUAL TRANSAXLE (E153)SHIFT LEVER AND CONTROL CABLE
MX±49
1850 Author: Date:
SHIFT LEVER AND CONTROL CABLE
COMPONENTS
Page 3025 of 4592
MX04V±02
Q10340
Shift Lever Knob
Center Console Upper Panel
Heater Control Assembly
Center Cluster
Finish Panel
Front Console Box
Shift Cable Grommet RetainerRear Console Box
Shift Lever Assembly
Select Control CableShift Control Cable Shift Cable Grommet
GrommetShift Cable
Grommet
Retainer
ClipWasher
12 (120, 9)
Clip Clip
ClipWasher
Washer
4.9 (50, 43 in.´lbf)
Clip ClipClip
Clip
4.9 (50, 43 in.´lbf)
N´m (kgf´cm, ft´lbf): Specified torque
± MANUAL TRANSAXLE (S51)SHIFT LEVER AND CONTROL CABLE
MX±43
1893 Author: Date:
SHIFT LEVER AND CONTROL CABLE
COMPONENTS
Page 3031 of 4592
PP0JS±04
PP±6
± PREPARATIONENGINE MECHANICAL (5S±FE)
58 Author: Date:
EQUIPMENT
Abrasive compoundValve
Caliper gauge
CO/HC meter
Compression gauge
Connecting aligner
Cylinder gauge
Dial indicator
Dye penetrant
Engine tune±up tester
Groove cleaning toolPiston ring groove
Heater
Magnetic finger
Micrometer
OBDII scan tool
Pin hole grinderPiston pin hole of piston
Piston ring compressor
Piston ring expander
Plastigage
Precision straight edge
Press
Ridge reamerCylinder
Soft brush
Solvent
Spring testerValve spring
Steel squareValve spring
Thermometer
Torque wrench
Valve seat cutter
V±block
Vernier calipers
Wire brushValve
Page 3037 of 4592
PP0BT±03
PP±12
± PREPARATIONENGINE MECHANICAL (1MZ±FE)
64 Author: Date:
EQUIPMENT
Abrasive compound
Caliper gauge
CO/HC meter
Connecting rod aligner
Cylinder gauge
Dial indicator
Dye penetrant
Engine tune±up tester
Groove cleaning tool
Heater
Magnetic finger
Micrometer
OBDII scan tool
Pin hole grinderPiston pin hole
Piston ring compressor
Piston ring expander
Plastigage
Precision straight edge
Ridge reamer
Soft brush
Spring testerValve spring
Steel squareValve spring
Thermometer
Torque wrench
Valve seat cutter
Vernier calipers
Wire brushValve
Page 3051 of 4592
PP0K1±03
PP±26
± PREPARATIONCOOLING (5S±FE)
78 Author: Date:
EQUIPMENT
HeaterECT switch, Thermostat
Radiator cap tester
ThermometerECT switch, Thermostat
Torque wrench
Vernier calipers
Page 3055 of 4592
PP0C2±02
PP±30
± PREPARATIONCOOLING (1MZ±FE)
82 Author: Date:
EQUIPMENT
HeaterECT switch
Radiator cap tester
ThermometerECT switch
Torque wrench
Page 3259 of 4592

SS109±02
± SERVICE SPECIFICATIONSSFI (1MZ±FE)
SS±21
184 Author: Date:
SFI (1MZ±FE)
SERVICE DATA
Fuel pressure
regulatorFuel pressure at no vacuum301 ± 347 kPa (3.1 ± 3.5 kgf/cm2, 44 ± 50 psi)
Fuel pumpResistance at 20°C (68°F)0.2 ± 3.0 W
InjectorResistance
Injection volume
Difference between each cylinder
Fuel leakage13.4 - 14.2 W
60 ± 73 cm3 (3.4 ± 4.5 cu in.) per 15 sec.
13 cm3 (0.8 cu in.) or less
1 drop or less per 12 minute
MAF meterResistance (THA ± E2) at ±20°C (±4°F)
at 20°C (68°F)
at 60°C (140°F)14.6 ± 17.8 kW
2.21 ± 2.69 kW
0.29 ± 0.35 kW
Throttle bodyThrottle opener setting speed900 ± 1,950 rpm
Throttle
position
sensorResistance
Throttle valve fully closed VTA ± E2
Throttle valve fully open VTA ± E2
± VC ± E2
0.2 ± 6.3 kW
2.0 ± 10.2 kW
2.5 ± 5.9 kW
IAC valveResistance (+B ± RSO or RSC) at cold
at hot17.0 ± 25.0 W
21.5 ± 29.5 W
VSV for EGRResistance at 20°C (68°F)27 ± 33 W
VSV for EVAPResistance at 20°C (68°F)27 ± 33 W
VSV for ACISResistance at 20°C (68°F)33 ± 39 W
VSV for Vapor
Pressure SensorResistance at 20°C (68°F)33 ± 39 W
Vapor
Pressure
SensorPower source voltage4.5 ± 5.5 V
ECT sensorResistance at ±20°C (±4°F)
at 0°C (32°F)
at 20°C (68°F)
at 40°C (104°F)
at 60°C (140°F)
at 80°C (176°F)10 ± 20 kW
4 ± 7 kW
2 ± 3 kW
0.9 ± 1.3 kW
0.4 ± 0.7 kW
0.2 ± 0.4 kW
EGR gas
temperature
sensorResistance at 50°C (122°F)
at 100°C (212°F)
at 150°C (302°F)64 ± 97 kW
11 ± 16 kW
2 ± 4 kW
A/F sensorHeater coil resistance at 20°C (68°F)
at 800°C (1472°F)0.8 ± 1.4 W
1.8 ± 3.2 W
Heated
oxygen sensorHeater coil resistance at 20°C (68°F)
at 800°C (1472°F)11 ± 16 W
23 ± 32 W
Fuel cut rpmFuel return rpm1,200 rpm